2018 FIAT 500 clock

IN AN EMERGENCY
138
SIDE LIGHTS / DAYTIME
RUNNING LIGHTS
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ turn the bulb holder B fig. 116
anticlockwise and remove it;
❒ remove the snap-fitted bulb and
replace it;
❒ refit the bulb holder B by turning it
clockwise and locking it correctly;
❒ reinstall the rubber cap.
DIRECTION INDICATORS
Front (POP versions)
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ turn the bulb holder A fig. 117
anticlockwise and pull it out;
❒ remove the snap-fitted bulb and
replace it;
❒ refit the bulb holder A by turning it
clockwise and locking it correctly;
❒ reinstall the rubber cap.
117DVDF0S0116c
Front (Excluding POP versions)
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ turn the bulb holder anticlockwise
and remove it;
❒ replace the bulb
bulb holder assembly;
❒ refit the bulb holder in its housing
A fig. 118 by turning it clockwise
and locking it correctly;
❒ refit the protection cap in its housing
and turn anticlockwise.
118DVDF0S0198c

139
Side
IMPORTANT The intervention must be
carried out taking all precautions
necessary to avoid damaging the
bodywork (use a sufficiently rigid and
appropriately thick plastic card).
To replace the bulb, proceed as
follows:
❒ lever the lens off, by initially applying
force from the front towards the
back (1-fig. 119);
❒ lever in the opposite direction, by
applying force from the back
part (2-fig. 119) and remove the
unit;
119DVDF0S0117c
❒ turn the bulb holder anticlockwise,
extract the press-fitted bulb and
replace it;
❒ reinstall the bulb holder into the
lens, then put back the assembly
making sure that the fixing clip has
clicked.
FRONT FOG LIGHTS
(for versions/markets, where provided)
For bulb replacement, contact a Fiat
Dealership.
REAR LIGHT CLUSTERS
To replace the bulb proceed as follows:
❒ open the tailgate;
❒ unscrew the two fastening screws
A fig. 120 and extract the light
cluster axially without rotating it;
❒ remove the bulb holder from its
housing releasing it from the locking
tabs B;
❒ extract the bulbs by pushing them
slightly and turning them counter-
clockwise.The bulbs are arranged as follows in
fig. 121:
C: tail / brake light;
D: direction indicators.
120DVDF0S0199c
121DVDF0S0200c

IN AN EMERGENCY
140
REVERSING LIGHT/REAR
FOG LIGHT
To replace the bulb, proceed as
follows:
❒ From inside the bumper, operate
the tabs A fig. 122 and remove the
press-fit flap;
❒ disconnect the electric connector
A-fig. 123;
❒ turn the bulb holder B fig. 123
anticlockwise and remove the unit;
❒ extract the bulb and replace it;
❒ refit the bulb/bulb holder unit B by
turning it clockwise
122DVDF0S0207c
❒ reconnect the electric connector A;
❒ refit the flap and check that it is
correctly locked.
THIRD BRAKE LIGHTS
To replace the bulb proceed as follows:
❒ remove the two guard caps and
unscrew the two fastening
screws A fig. 124;
❒ remove the assembly;
❒ disconnect the electric connector
B fig. 125;
❒ press the retaining device C and
open the bulb holder;
123DVDF0S0208c
❒ remove the press-fitted bulb to be
replaced and replace it;
❒ close the bulb holder making sure
the retaining device is correctly
locked;
❒ screw in the two fastening screws
and reinstall the guard caps.
124DVDF0S0124c
125DVDF0S0125c

IN AN EMERGENCY
142
FuseAmpereDescription
F13 5 •
Left dipped headlight and headlight alignment control unit power supply
F36 15 Diagnosis socket, radio, climate control, EOBD
F37 5 Brake light switch, instrument panel node
F38 15 Central door locking
F43 15 Windscreen/rear window washer pump
F47 20 Driver’s side power window
F48 20 Passenger’s side power window
F49 5 Parking sensor, control backlighting, electric mirrors
F51 7.5 Climate control, brake lights, clutch, sunroof, electric mirrors
F53 5 Instrument panel node
•
For versions/markets, where provided
ENGINE COMPARTMENT
JUNCTION BOX
The fuse box is located on the right
side of the engine compartment.
To access the fuses, proceed as
follows:
❒ Fully press the screw A fig. 130;
❒ at the same time slowly rotate the
screw anticlockwise, until resistance
is encountered (do not overtighten);
❒ slowly release the screw;
❒ opening is indicated by the entire
screw head coming out of its
housing;
❒ remove cover B, sliding it upwards
on the side guides, as indicated in
the figure.
❒ after replacing the fuse, refit the
cover, making sure that it is closed
properly.
130DVDF0S0201c

207
• Although the LPG system has numerous safety features, it is
advisable to proceed as follows every time the vehicle is not in
use for a long period or moved in an emergency as a result of a
breakdown or accident:
unscrew the fastening devices, then remove the cover B. Close
the LPG valve rotating the ring nut C clockwise; refit the cover and
tighten the fixing devices.
• It is strictly forbidden to use any additive in the LPG.
• Periodically (at least once every six months) it is advisable to
let the LPG in the tank run out and, at the first refuelling, check
that it does not exceed the maximum capacity of 30.5 litres
(including reserve). If the level is above 30.5 litres (reserve
included) contact a Fiat Dealership immediately.
In special usage conditions:
• starting up and operation at low ambient temperature
• LPG supply with low propane content: the system may
switch temporarily to petrol operation, without any indication.
In the case of:
• low LPG levels in the tank
• request for high performance (e.g. overtaking, car fully laden,
steep hills): the system can automatically switch to petrol
operation to guarantee the required engine performance; in this
event, the performed switching is shown by the orange (petrol)
LED lit and the green (LPG) LED off on the switch. When the
above conditions stop, the system automatically restores the
LPG operation; the orange (petrol) LED turns off and the green
(LPG) LED is lit on the switch.
(CONTINUED)
VEHICLE SAFETY
• To achieve the automatic switching described above, make sure
that there is always enough fuel in the petrol tank.
• There must therefore always be enough petrol in the tank to
protect the petrol pump and to guarantee temporary switching
from LPG to petrol operation.
30) CHANGING A WHEEL
When turning the jack handle make sure that it can turn freely
without scraping your hand against the ground. The moving
components of the jack (“worm screw” and joints) can also cause
injuries: avoid touching them. If you come into contact with
lubricating grease, clean yourself thoroughly.
31) FIX&GO QUICK TYRE REPAIR KIT
• The sealant fluid is effective with external temperatures between
-40°C and +55°C. The sealant has an expiry date. It is possible to
repair tyres which have been damaged on tread up to a diameter
of 6 mm. Show the cartridge and the label to the personnel
charged with handling the tyre treated with the tyre repair kit.