2018 FIAT 500 Ignition switch

KNOWING YOUR CAR
16
Start&Stop SYSTEM DEACTIVATION (for versions/markets, where provided)
The deactivation of the Start&Stop system, is indicated by the lighting of the warning light or the symbol on the display
along with a dedicated message on the display on some versions.
TT
START&STOP SYSTEM ACTIVE (for versions/markets, where provided)
This warning light switches on with fixed light, along with a dedicated message on the display on some versions , in the
case of Start&Stop system failure.
UU
INJECTION / EOBD SYSTEM FAULT
Under normal conditions, the warning light comes on when the ignition key is turned to MAR, but should go off as soon as
the engine is started.
The warning light remains on or switches on whilst driving, on some versions together with a dedicated message on the
display, if the injection system is not working properly. In particular, if the warning light switches on continuously, it indicates
a malfunction in the supply/ignition system that could cause excessive exhaust emissions, a possible loss of performance,
poor driveability and high fuel consumption.
Under these conditions, the vehicle can continue travelling at moderate speed without demanding excessive effort from the
engine.
Prolonged use of the car with the warning light on may cause damage.
Contact a Fiat Dealership as soon as possible.
Petrol engines only
If the warning light is flashing, this indicates that the catalytic converter may be damaged.
If the warning light flashes, it is necessary to release the accelerator pedal to lower the speed of the engine until the warning
light stops flashing; continue the journey at moderate speed, trying to avoid driving conditions that may cause further
flashing and contact a Fiat Dealership as soon as possible. START&STOP SYSTEM FAULT (versions with colour display) (for versions/markets, where provided)
The symbol appears, along with a dedicated message on the display on some versions, in the case of Start&Stop system
fault. Go to Fiat Dealership as soon as possible.
jj
UU

17
FUEL RESERVE - LIMITED RANGE
The warning light switches on when the ignition key is turned to MAR, but it should switch off after a few seconds.
The warning light or the symbol switches on in the display when about 5 litres of fuel are left in the tank. The triangle on the
right side of the symbol indicates the side of the car with the fuel filler.
IMPORTANT If the warning light flashes or the symbol is constantly on, depending on the versions, there is a fault in the
system. If this is the case, go to a Fiat Dealership to have the system checked.
GLOW PLUG/GLOW PLUG PREHEATING FAULT (diesel versions)
Glow plugs
This warning light switches on when the key is turned to MAR (for versions/markets, where provided). It will switch off as
soon as the glow plugs have reached a preset temperature. The engine can be started as soon as the warning light
switches off.
IMPORTANT At moderate or high ambient temperatures the warning light may stay on for an extremely short time.
Glow plug preheating failure
The warning light will flash, on some versions along with a dedicated message on the display, to indicate a fault in the plug
preheating system.
In these cases, contact a Fiat Dealership as soon as possible to have the fault fixed.
mm
DPF CLEANING (PARTICULATE TRAP) IN PROGRESS (diesel versions with DPF)
The warning light switches on when the ignition key is turned to MAR, but it should switch off after a few seconds.
The warning light or symbol appears on the display fixed, on some versions along with a dedicated message on the display,
to notify the driver that the DPF system needs to eliminate captured pollutants (particulate) through the regeneration
process.
The warning light remains off during the regeneration process; it switches on only if the driving conditions require the driver
to be alerted.
To switch the warning light off definitively, the vehicle must be kept moving until the regeneration process is completed.
On average, the process lasts 15 minutes.
Optimal conditions for completing the process are achieved by travelling at 60 km/h with engine speed above 2000 rpm.
When this warning light switches on, it does not indicate a vehicle failure and thus it should not be taken to a workshop. On
some versions, together with the warning light switching on, the display shows a dedicated message.
tt

19
ESC SYSTEM (for versions/markets, where required)
The warning light switches on when the ignition key is turned to MAR, but it should switch off after a few seconds.
ESC system activation
Flashing of the warning light while driving indicates the intervention of the ESC system.
ESC system failure
If the warning light does not go off or stays on together with the LED on the ASR OFF button while driving.
The display will show a dedicated message.
Contact a Fiat Dealership.
Hill Holder failure
This warning light switches on, on some versions together with a dedicated message on the display, in the event of a Hill
Holder system fault.
In this case, contact a Fiat Dealership as soon as possible. Parking sensor fault
The warning light turns on and the dedicated message is shown on the display when a parking sensor fault is detected.
Start&Stop system fault (versions with multifunction display)
A fault of the system is indicated by the warning light switching on. A dedicated message will appears on the instrument
panel.
Airbag warning light fault (for versions/markets, where provided)
The warning light will blink when a fault of the
¬warning light is detected.
ESCESC
BRAKE PAD WEAR
The warning light switches on, together with a dedicated message on the display, if the front or rear brake pads (on
version/markets, where provided) are worn.
In this case have them replaced as soon as possible.
dd
POSSIBLE ICE ON ROAD
The symbol is shown on the display (on some versions together with a dedicated message) when the outside temperature
is equal to or below 3°C.
èè
(versions with
multifunction
display)
(versions with
multifunction
display)

27
HEADLIGHT
ALIGNMENT
With the ignition key at MAR and
dipped beam headlights on, press the
+ button to adjust the headlights
upwards and the – button to adjust the
headlights downwards.
TYRE RESET (ITPMS
RESET)
(for versions/markets, where provided)
With this function it is possible to reset
the iTPMS (see paragraph “iTPMS”). To
carry out the Reset procedure proceed
as follows:
❒ briefly press the MENU
N; the
display will show “Reset”;
❒ press button + or – to select (“Yes”
or “No”); a dedicated reset
confirmation message will appear;
❒ briefly press the MENU
N; the
display will show “Confirm”;
THE KEYS1)
1) 1)
CODE CARD
(for versions/markets, where provided)
The car is delivered with two copies of
the ignition key and with the CODE
card fig. 7 which bears the following:
A: the electronic code;
B: the mechanical key code to be given
to the Fiat Dealership when ordering
duplicate keys.
You should have the electronic code
with you at all times.
IMPORTANT All the keys and the
CODE card must be handed over to
the new owner when selling the car.
MECHANICAL KEY
The metal insert A-fig. 8 operates:
❒ the ignition switch;
❒ the door locks and the tailgate (for
versions/markets, where provided);
❒ the locking/unlocking of the fuel
cap.
KEY WITH REMOTE
CONTROL
(for versions/markets, where provided)
The metal insert A-fig. 9 operates:
❒ the ignition switch;
❒ the door locks;
❒ the locking/unlocking of the fuel
cap.
7DVDF0S0103c
8DVDF0S0104c

KNOWING YOUR CAR
28
FIAT CODE
SYSTEM
The Fiat Code system is an electrical
engine immobiliser system which
increases protection against attempted
car theft. It is automatically activated
when the ignition key is removed.
Each time the vehicle is started by
turning the ignition key to MAR, the Fiat
CODE system control unit sends a
recognition code to the engine control
module to deactivate the immobiliser.
If, during ignition, the code is not
correctly recognized, a warning light
is lit on the instrument panel .
In this case, turn the key to STOP and
then to MAR-ON; if it is still locked, try
again with the other keys that come
with the car.
Contact a Fiat Dealership if you still
cannot start the engine.
NOTE Each key has its own code
which must be stored by the control
unit of the system.
Contact a Fiat Dealership to have new
keys (up to 8) stored with a code.
IGNITION
DEVICE
The key can be turned to three
different positions fig. 10:
❒ STOP: engine stopped, key can be
removed, steering column locked.
Some electrical devices (e.g. audio
system, central door locking
system, etc.) can operate;
❒ MAR: driving position.
All electrical devices are enabled;
❒ AVV: engine starting.
The ignition device is fitted with a
safety system that requires the ignition
key to be turned back to STOP if the
engine does not start, before the
starting operation can be repeated.
10DVDF0S011c
Pressing button B opens/closes the
metal insert.
Briefly press button
Ë: for unlocking of
doors and tailgate, timed switching-on
of interior lights and double flashing of
direction indicators (for
versions/markets, where provided).
Briefly press button
Á: for remote
locking of doors and tailgate,
switching-off of the internal ceiling
lights and single flashing of direction
indicators (for versions/markets, where
provided).
Press the Rbutton: remote opening
of the luggage compartment and
double flashing of the direction
indicators.
9DVDF0S0105c

KNOWING YOUR CAR
36
It is possible to enable this function
within 2 minutes after turning off the
engine. This function allows turning on
lights and low beams. It is possible to
set the headlights turning on time by
pulling the left lever towards the
steering wheel (unstable position) one
or more times. In this case it is
possible to choose between 0, 30, 60,
90 up to a maximum of 210 seconds.
Each time the stalk is operated, the
warning light
3on the instrument
panel switches on. The display shows
a message and the time set for the
function.
The
3warning light comes on when
the stalk is first moved and stays on
until the function is automatically
deactivated.
Deactivation
This function is deactivated turning on
again the headlights, sidelights or
pulling the left lever towards the
steering wheel (unstable position) for
more than 2 seconds, or switching the
starter to MAR.
AUTO FUNCTION
(Dusk sensor)
(for versions/markets, where provided)
This is an infrared LED sensor that works
in conjunction with the rain sensor. It is
located on the windscreen (fig. 25) and is
able to detect variations in outside
lighting based on the light sensitivity set
in the display Menu or the Uconnect™
5" or 7" HD system (where provided).
The higher the sensitivity, the lower the
amount of external light needed to
automatically switch the external lights
on.
25DVDF0S0215c
Function activation
Turn the left stalk ring A fig. 26 to the
AUTOposition.
IMPORTANT The function can only be
activated with the ignition device in the
MAR position.
Function deactivation
To deactivate the function, turn the left
stalk ring A to position 2.
26DVDF0S0216c

KNOWING YOUR CAR
38
With the windscreen wiper on and
reverse gear engaged, rear window
wiping will be continuous in the same
way.
“Smart washing” function
❒ Push the lever towards the
dashboard and hold it in position to
activate the rear window washer jet.
RAIN SENSOR
(for versions/markets, where provided)
4)
The sensor will be activated when the
ignition device is turned to MAR, and
will be deactivated in the STOP
position.
29DVDF0S0217c
This is a device located behind the
interior rear view mirror fig. 30, in
contact with the windscreen. It can
measure the amount of rain and,
consequently, control the automatic
windscreen wiping mode depending
on the amount of water on the
windscreen.
IMPORTANT Keep the window clean in
the sensor area.
AUTOMATIC WIPING
(for versions/markets, where provided)
Activation
The user can choose automatic wiping
by moving the right steering wheel
stalk fig. 28 to the AUTO (B) position.
The activation of the automatic wiping
will be notified to the driver by a single
stroke.
30DVDF0S0215c
Sensitivity Adjustment
The rain sensor sensitivity can be
adjusted through the display menu or
on the UconnectTM 5" or 7” system.
Inhibition
If the starter switch is moved to the
STOP position, leaving the right
steering wheel stalk in the AUTO (B)
position, when the vehicle is next
started (starter switch in the MAR
position), no wiping cycle to prevent
damage to the system if the
windscreen is being washed manually
or if there is ice on it.
To re-enable the automatic wiping
mode:
❒ Put the right steering wheel stalk in
a position other than AUTO and
then back to the AUTO position;
❒ exceed the speed of 5 km/h when
the sensor detects rain.
Deactivation
The user can disable automatic wiping
by moving the right steering wheel
stalk to a position other than AUTO.

45
BOOT 13)
ELECTRIC HANDLE
(SOFT TOUCH)
❒ Operate the electric handle A-fig. 41
to open the tailgate.
❒ To release the lock manually, use
the metal insert of the ignition key.
❒ To release the lock with the remote
control, press button R.
❒ To close, use the handle located
inside the tailgate.
❒ If the tailgate is not shut properly the
dedicated instrument panel or
colour display warning light (where
provided) will switch on.
41DVDF0S025c
Opening the tailgate with soft top
all open
❒ Pressing the tailgate opening
one-touch button A-fig. 41 to
automatically close the soft top to
spoiler position. The tailgate can be
opened in spoiler position.
Hatchback emergency opening
To open the tailgate from the
passenger compartment if the car
battery is run down or the electric
tailgate lock is faulty, proceed as
follows:
❒ remove the rear head restraints;
❒ fold the seat backrests over;
❒ press lever A-fig. 42 inside the
luggage compartment.
42DVDF0S026c
ROOF RACK/SKI
RACK 14) 7)
FASTENERS
The fasteners are located in the areas
shown in fig. 43.
To use the front fasteners, remove the
cap A fig. 43, accessible with the door
open.
The rear fixing areas B can be found
according to measurements shown in
fig. 44.
Lineaccessori Mopar
®at provides a
specific roof rack/ski rack for the
tailgate.
43DVDF0S178c