2018 CITROEN DS3 Handbook (in English)

111
ISOFIX mountings
The seats, illustrated below, are fitted with
regulation ISOFIX mountings:There are three rings for each seat:
Remove and stow the head restraint
before installing a child seat with
a backrest on a passenger seat. Refit the
head restraint once the child seat has
been removed.
(a)
Universal child seat: child seat which
can be installed in all vehicles using
the seat belt.
(b) Group 0: birth to 10

kg. Carrycots and
car beds cannot be installed in the
front passenger seat.
(c) Refer to the current legislation in your
country before putting your child in this
seat.
(d) To install a

child seat at the rear,
rear ward or for ward facing, move the
front seat for ward, then adjust the
backrest to an upright position to allow
enough room for the child seat and the
child's legs.
(e) When a

rear ward facing child seat
is installed on the front passenger
seat, it is essential to deactivate the
passenger's airbag. Otherwise, the
child would risk being seriously injured
or killed if the airbag were deployed.
When a

for ward facing child seat is
installed on the front passenger seat,
the passenger's airbag must remain
activated.
(f ) A child seat with a

support leg must
never be installed on the centre rear
passenger seat. U:
Seat suitable for the installation of
a child seat secured using a seat belt
and universally approved, rearward
facing and/or forward facing.
U(R): Same as U , with the passenger seat
adjusted to the highest position and in
the longitudinal intermediate position.
-
t
wo rings A
, located between the vehicle
backrest and cushion, indicated by a label,
-
a r
ing B, located behind the seat, referred
to as the TOP TETHER , for fixing the upper
strap.
The TOP TETHER secures the upper strap
of child seats that have one. In case of frontal
impact, this device limits the tilting of the child
seat forward.
05
Safety

11 2
This ISOFIX mounting system provides fast,
reliable and safe fitting of the child seat in your
vehicle.
The ISOFIX child seats are fitted with two
latches which are secured on the two rings A.
Some seats also have an upper strap , which is
attached to ring B .
To secure the child seat to the Top Tether:
-

r
emove and stow the head restraint before
installing the child seat on the seat (refit it
once the child seat has been removed),
-

p
ass the strap of the child seat behind
the top of the backrest, centring the holes
between the head restraint rods,
-

f
ix the hook of the upper strap to ring B ,
-

t
ighten the upper strap.
When installing an ISOFIX child seat on the
right-hand rear seat, before securing the seat,
first move the centre rear seat belt towards the
middle of the vehicle, so as to not inter fere with
the operation of the seat belt.
For information on installing ISOFIX child seats
in your vehicle, refer to the summary table.Recommended ISOFIX child
seats
Also consult the installation notes of the
child seat's manufacturer to find out how
to install and remove the seat. "
RÖMER Duo Plus ISOFIX "
(size category: B1 )
Group 1: from 9 to 18 kg
Is installed only in the forward facing position. Is attached to the rings A and the
ring B , referred to as the TOP TETHER,
using an upper strap.
Three seat body angles: sitting, reclining, lying down.
This child seat can also be used on seats not equipped with ISOFIX mountings. In
this case, it must be secured to the vehicle's seat by the three-point seat belt. Adjust the
position of the vehicle's front seat so that the child's feet are not touching the backrest.
05
Safety

11 3
Summary table of locations for ISOFIX child seats
In line with European regulations, this table indicates the options for installing ISOFIX child seats on the vehicle seats fitted with ISOFIX mountings.
In the case of universal and semi-universal ISOFIX child seats, the ISOFIX size category, determined by a letter from A to G, is indicated on the child
seat next to the ISOFIX logo.
Weight of the child and indicative age
Less than 10
kg
(group 0)
Up to about 6
monthsLess than 10
kg (group 0)
Less than 13
kg
(group 0+)
Up to 1
year approxFrom 9
to 18 kg (group 1)
From about 1
to 3 years old
Type of ISOFIX child seat Carr ycotRearward facing Rearward facing Forward facing
ISOFIX size categor y F G C D E C D A B B1
ISOFIX child seats universal and semi-
universal which can be installed on the rear outer seats X
XIL- SU* XIL- SU* IUF
IL- SU
IL- SU: seat suitable for the installation of
an Isofix S emi-Universal seat which
can be:
-

"
rear ward facing" fitted with an
upper strap or a
support leg,
-

"
for ward facing" fitted with
a
support leg,
-

a c
arrycot fitted with an upper
strap or a
support leg.
For advice on securing the upper strap refer to
the "ISOFIX mountings" section. X:
seat not suitable for the installation of
a
child seat or an ISOFIX carrycot for the
weight group indicated.
Remove and stow the head restraint
before installing a
child seat with
a
backrest on a passenger seat. Refit the
head restraint once the child seat has
been removed.
*

T
o install a child seat at the rear, rear ward
facing, move the front seat for ward, then
straighten the backrest to allow enough
room for the child seat and the child's legs.
I UF: seating position suitable for the
installation of an I sofix Universal seat,
F or ward facing secured using the
"TOP TETHER" upper strap.
05
Safety

11 4
Advice
The incorrect installation of a child seat in
a vehicle compromises the child's protection
in the event of an accident.
Ensure that there is no seat belt or seat belt
buckle under the child seat, as this could
destabilise it.
Remember to fasten the seat belts or the
child seat harnesses keeping the slack
relative to the child's body to a
minimum,
even for short journeys.
When installing a


child seat using the seat
belt, ensure that the seat belt is tightened
correctly on the child seat and that it secures
the child seat firmly on the seat of your
vehicle. If your passenger seat is adjustable,
move it for wards if necessary.
At rear seating positions, always leave
sufficient space between the front seat and:
-

a r
ear ward facing child seat,
-

t
he child's feet for a child seat fitted
forward facing.
To do this, move the front seat for wards
and, if necessary, move its backrest into the
upright position.
For optimal installation of the "forward facing"
child seat, verify that its backrest is as close
as possible to the backrest of the vehicle
seat, if possible in contact with it. The head restraint must be removed
before installing a
child seat with
a
backrest on a passenger seat.
Ensure that the head restraint is stored or
attached securely to prevent it from being
thrown around the vehicle in the event of
sharp braking. Refit the head restraint when
the child seat is removed.
Children at the front
The legislation on carrying children on the
front passenger seat is specific to each
country. Refer to the legislation in force in
your country.
Deactivate the passenger's front airbag when
a
rear ward facing child seat is installed on the
front passenger seat.
Otherwise, the child risks being seriously
injured or killed if the airbag is deployed.
Installing a


booster seat
The chest part of the seat belt must be
positioned on the child's shoulder without
touching the neck.
Ensure that the lap part of the seat belt
passes correctly over the child's thighs. We recommend using a
booster seat with
a backrest equipped with a belt guide at
shoulder level.
As a
safety precaution, do not leave:
-

a c
hild or children alone and unattended in
a


vehicle,
-

a c
hild or an animal in a vehicle under the
sun, with the windows closed,
-

t
he keys within the reach of children inside
the vehicle.
To prevent accidental opening of the doors
and rear windows, use the child lock.
Take care not to open the rear windows by
more than one third.
To protect young children from the rays of the
sun, fit side blinds on the rear windows.
05
Safety

DRIVING
06

11 6
Driving recommendations
Observe the driving regulations and remain
vigilant whatever the traffic conditions.
Pay close attention to the traffic and keep your
hands on the wheel so that you are ready to
react at any time to any eventuality.
As a safety measure, the driver should only
carry out any operations that require close
attention when the vehicle is stationary.
On a
long journey, a break every two hours is
strongly recommended.
In bad weather, drive smoothly, anticipate the
need to brake and increase the distance from
other vehicles.
Never leave the engine running in
an enclosed area without adequate
ventilation: internal combustion engines
emit toxic exhaust gases, such as carbon
monoxide. There is a
risk of poisoning and
death!
In very severe wintry conditions
(temperatures below -23°C), to guarantee
correct operation and the longevity of
the mechanical elements of your vehicle,
engine and gearbox, the engine must be
left running for 4
minutes before driving.
Important!
Never drive with the parking brake
applied – Risk of overheating and damage
to the braking system!
As the exhaust system of your vehicle
is very hot, even several minutes after
switching off the engine, never park or run
the engine on inflammable sur faces (dry
grass, dead leaves, etc.) – Risk of fire!
Never leave a vehicle unsuper vised with
the engine running. If you have to leave
your vehicle with the engine running, apply
the parking brake and put the gearbox into
neutral or position N or P , depending on
the type of gearbox.
Driving on flooded roads
We strongly advise against driving on flooded
roads, as this could cause serious damage
to the engine or gearbox, as well as to the
electrical systems of your vehicle. If you are obliged to drive through water:
-

c
heck that the depth of water does not
exceed 15 cm, taking account of waves that
might be generated by other users,
-
d
eactivate the Stop & Start function,
-
d
rive as slowly as possible without stalling.
In all cases, do not exceed a speed of
6 mph (10 km/h),
-
d
o not stop and do not turn off the engine.
On leaving the flooded road, and as soon as it
is safe to do so, brake lightly several times to
dry the brake discs and pads.
If in doubt about the state of your vehicle,
contact the dealer network or a qualified
workshop.
06
Driving

11 7
In case of towing
Driving with a trailer places greater
d emands on the towing vehicle and
requires extra care from the driver.
Distribution of loads
F Distribute the load in the trailer so that the heaviest items are as close as possible to
the axle and the nose weight approaches
the maximum permitted without exceeding
it.
Air density decreases with altitude, thus
reducing engine performance. The maximum
towed load must be reduced by 10% for every
1,000
metres of altitude.
Please respect the maximum towable
weights.
Side wind
F Take into account the increased sensitivity to wind.
Cooling
Towing a trailer on a slope increases the
t emperature of the coolant.
As the fan is electrically controlled, its cooling
capacity is not dependent on the engine speed.
F

T
o lower the engine speed, reduce your
speed.
The maximum towable load on an incline
depends on the gradient and the exterior
temperature.
In all cases, keep a
check on the coolant
temperature.
F

I
f this warning lamp and the
STOP warning lamp come on,
stop the vehicle and switch off
the engine as soon as possible.
New vehicle
Do not pull a trailer before having driven at least
approximately 600


miles (1,000

kilometres).
Braking
Towing a trailer increases the braking distance.
T o avoid overheating of the brakes, the use of
engine braking is recommended.
Ty r e s
F Check the tyre pressures of the towing vehicle and of the trailer, observing the
recommended pressures.
Lighting
F Check the electrical lighting and signalling on the trailer and the headlamp beam height
of your vehicle.
For more information on Headlamp
beam height adjustment , refer to the
corresponding section.
The rear parking sensors will be
deactivated automatically to avoid
the audible signal if a
genuine
DS
AUTOMOBILES towbar is used.
If the exterior temperature is high, it is
recommended that the engine be allowed
to idle for 1
to 2 minutes after the vehicle
comes to a
stop, to facilitate its cooling.
06
Driving

11 8
Starting-switching off the
engine
Anti-theft protection
Electronic immobiliser
The key contains an electronic chip which has
a secret code. When the ignition is switched
on, this code must be recognised to enable
engine start.
This electronic engine immobiliser locks the
engine management system a


moment after
the ignition is switched off, and prevents
unauthorised engine starting.
In the event of a
fault, you are
informed by the illumination of this
warning lamp, an audible signal and
a
message in the screen.
In this case, your vehicle will not start; contact
the dealer network as soon as possible.
Keep safely, away from your vehicle, the
label attached to the keys given to you
when you purchased your vehicle.
Ignition switch
Ignition on position
It allows the use of the vehicle's electric
equipment or portable devices to be charged.
Once the state of charge of the battery drops
to the reser ve level, the system switches to
energy economy mode: the power supply is
cut off automatically to preser ve the remaining
battery charge.
Avoid attaching heavy objects to the key
or the remote control, which would weigh
down on its blade in the ignition switch
and could cause a


malfunction.
Starting the engine
It has 3 positions:
- P osition 1: Stop
-

P
osition 2: Ignition on
-

P
osition 3: Starting F

A
pply the parking brake.
F
W
ith a manual gearbox, place the gear
lever in neutral then fully depress the clutch
pedal.
F
W
ith an electronic gearbox, place the lever
at position N then firmly press the brake
pedal.
F
W
ith an automatic gearbox, place the lever
at position P then firmly press the brake
pedal.
F

I
nsert the key into the ignition switch; the
system recognises the code.
F

U
nlock the steering column by
simultaneously turning the steering wheel
and the key.
In certain cases, you may have to apply
significant force to move the steering
wheel (wheels on full lock, for example).
F

W
ith a petrol engine, operate the starter
motor by turning the key to position
3
without pressing the accelerator pedal,
until the engine starts. Once the engine is
running, release the key.
F

W
ith a Diesel engine, turn the key to
position 2 , ignition on, to operate the engine
pre-heating system.
06
Driving