2018 CITROEN DS3 fold seats

57
If the vehicle is to be parked outside for
a long period, it is advisable to protect the
roof using a


tarpaulin.
It is advisable to close the roof when you
park the vehicle.
Even if the roof is closed, it is safer not to
leave any valuables inside the vehicle.
Remove the ignition key when you leave
the vehicle to prevent any involuntary roof
movement.
If your vehicle has a
voice command
system, it may be affected if you drive with
the roof open.
Protection of electric motors that control
roof opening and closure: during repeated
opening and closing movements of the
roof, it is possible that heating up of the
electric motors no longer allows the roof to
be opened or closed. Allow the motors to
cool by not trying to move the roof for ten
minutes.Boot
Opening
Closing
- when the engine is running ,
this warning lamp comes on,
accompanied by a
message in
the multifunction screen for a
few
seconds,
-

w
hen the vehicle is moving
(speed higher than 6
mph
(10
km/h)), this warning lamp
comes on, accompanied by an
audible signal and a
message in
the multifunction screen for a
few
seconds.
Back-up control
Unlocking
F Fold back the rear seats to gain access to the lock from inside the boot.
F

I
nsert a small screwdriver into hole A of the
lock to unlock the boot.
F

A

fter unlocking the vehicle, press the
opening control and then open the boot.
F

L

ower the tailgate using the interior grab
handle.
If the tailgate is not fully closed: Measures for mechanically unlocking the boot
in the event of a battery or central locking fault.
02
Access

59
If the roof per forms an opening
manoeuvre in zone B, an action on the
boot opening command causes the roof to
close. The boot will be opened when the
roof has reached position 2 . You can then
raise the tailgate.
If the roof per forms an closing manoeuvre
in zone B , an action on the boot opening
command has no effect on the roof
manoeuvre, but triggering the opening of
the tailgate will only be effective when the
roof has reached position 2 . You can then
raise the tailgate.
If the roof per forms an opening or closing
manoeuvre in zone B following an
"anti-panic" function, the boot opening
command is inhibited. It will operate again
when the roof has reached position 2
or
position 3 .
If the roof is in position 3 , an action on
the boot opening control causes the roof
to close to position 2 . When the roof has
reached this position, the tailgate opening
will be triggered. You can then raise the
tailgate.Back-up control
Measures for mechanically unlocking the boot
in the event of a battery or central locking fault.
Unlocking
F Fold the rear seats to gain access to the two locks from inside the boot. F

I
nsert a small screwdriver into hole A of
each side lock to unlock the boot.
Before opening the boot, check that the
roof is not in zone B .
02
Access

63
Do not use the function when the seat is
not occupied.
Reduce the intensity of the heating as
soon as possible.
When the seat and passenger
compartment have reached an adequate
temperature, you can stop the function;
reducing the consumption of electrical
current reduces fuel consumption.Prolonged use at the highest setting is
not recommended for those with sensitive
skin.
There is a
risk of burns for people whose
perception of heat is impaired (illness,
taking medication, etc.).
There is a
risk of overheating the system if
material with insulating properties is used,
such as cushions or seat covers.
Do not use the system:
-

i
f wearing damp clothing,
-

i
f child seats are fitted.
To avoid breaking the heating element in
the seat:
-

d
o not place heavy objects on the seat,
-

d
o not kneel or stand on the seat,
-

d
o not place sharp objects on the seat,
-

d
o not spill liquids onto the seat.
To avoid the risk of short-circuit:
-

d
o not use liquid products for cleaning
the seat,
-
n

ever use the heating function when
the seat is damp.Access to the rear seats
Ensure that only the appropriate control is
used, located at the top of the backrest.
F

T
o return the seat to its initial position, push
the backrest back again.
In case of difficulty, push back
simultaneously on the seat backrest angle
adjustment control (at the bottom of the
backrest) and the backrest.
F

P
ull the control up to fold down the backrest
and move the seat for ward.
03
Ease of use and comfort

65
Adjusting the seat backrest angle
F Push the handle towards the rear and move the seat backrest for wards or backwards.
Before moving the seat backwards,
ensure that there is nothing that might
prevent the full travel of the seat.
There is a
risk of trapping or pinching
passengers if present in the rear seats
or jamming the seat if large objects are
placed on the floor behind the seat.
Additional adjustments
Access to the rear seats
F Pull the control for ward to fold the backrest and move the seat for ward.
When returning it, the seat resumes its
initial position.
No person or object should block the
seat sliding back into its initial position;
returning to this position is necessary for
longitudinal locking.
Make sure that the seat belt has reeled in
correctly so as not to prevent passenger
access to the rear seats.
Grab handle
This ergonomic grip, located at the top of the
side trim, allows:
-
r
ear side passengers to have a support
when the vehicle is moving,
-

p
rovision of a support point improving
access to seats in the rear,
-

e
asier exit from the rear seats.
03
Ease of use and comfort

66
Rear seats
Bench seat with fixed one-piece cushion and
folding backrest (1/3 -2/3) to adapt the loading
space in the boot.
Folding the backrestReturning the backrest to the
normal position
F Straighten the seat backrest 2 and secure it.
F C heck that the red indicator, located next to
the control 1 , is no longer visible.
When repositioning the seat backrest,
take care not to trap the seat belts.
Rear head restraints
Never drive with the head restraints
removed; they must be fitted and correctly
adjusted.
F

M

ove the corresponding front seat for wards
if necessary.
F
P
osition the seat belt against the backrest.
F
P
lace the head restraints in the low position. F

P

ull control 1

for wards to release the seat
backrest 2 .
F

F

old the seat backrest 2

on to the cushion.
These have one position for use (up) and
a

stowed position (down).
They can also be removed.
To remove a head restraint:
F

r

elease the backrest using the control 1
,
F

t

ilt the backrest 2 slightly forwards,
F

p
ull the head restraint upwards to the stop,
F

t

hen, press the lug A
.
03
Ease of use and comfort

100
Advice
The driver must ensure that the passengers
use the seat belts correctly and that they are
all fastened before driving.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for short
journeys.
Do not interchange the seat belt buckles as
they will not completely fulfil their role.
The seat belts are equipped with an inertia
reel which allows the strap length to adjust
automatically to your shape. The seat belt is
stowed automatically when not in use.
Before and after use, ensure that the seat belt
is reeled in correctly.
The lower part of the strap must be positioned
as low as possible on the pelvis.
The upper part must be positioned in the
hollow of the shoulder.
The inertia reels have an automatic blocking
device at the time of a collision, during
sudden braking or if the vehicle turns over.
You can release the device by pulling the
strap firmly and then releasing it so that it
reels in slightly. In order to be effective, a seat belt must:
-
b e tightened as close to the body as
possible,
-

b
e pulled in front of you with a smooth
movement, checking that it does not twist,
-

b
e used to restrain only one person,
-

n
ot show any signs of cuts or fraying,
-

n
ot be converted or modified to avoid
affecting its performance. Recommendations for children
Use a
suitable child seat if the passenger is
less than 12
years old or shorter than one and
a
half metres.
Never use the same seat belt to secure more
than one person.
Never allow a
child to travel on your lap.
For more information on Child seats , refer to
the corresponding section.
In accordance with current safety regulations,
for all repairs on your vehicle's seat belts, go
to a
qualified workshop with the skills and
equipment needed, which the dealer network
is able to provide.
Have your seat belts checked regularly in
the dealer network or a
qualified workshop,
particularly if the straps show signs of
damage.
Clean the seat belt straps with soapy water or
a
textile cleaning product, sold in the dealer
network.
After folding or moving a
seat or a rear bench
seat, ensure that the seat belt is positioned
and reeled in correctly. In the event of an impact
Depending on the nature and seriousness
of the impact
, the pyrotechnic device may
be deployed before and independent of the
airbags. Deployment of the pre-tensioners
is accompanied by a
slight discharge of
harmless smoke and a
noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system.
In all cases, the airbag warning lamp comes
on.
Following an impact, have the seat belt
system checked, and if necessary replaced,
in the dealer network or by a
qualified
workshop.
05
Safety