2017 MAZDA MODEL CX-5 instrument cluster

If the BSM warning indicator lights are difficult to see due to glare from surrounding
brightness when travelling on snow-covered roads or under foggy conditions, press the
dimmer cancellation button to cancel the dimmer and increase th e brightness of BSM
warning indicator light s when they turn on.
Refer to Instrument Panel Illumination on page 4-26.
Display indicato r (Vehicles with multi-i nformation display and active driving display)
The detected approaching vehicle and warning are displayed in t he multi-information
display and active driving display when the vehicle is moving f orward (BSM operational).
Multi-information DisplayActive Driving Display
Detection and warning indicator Detection and warning indicator
The detected direction is displayed with a detection indicator (white) when an approaching
vehicle is detected. In addition, if the direction indicator le ver is operated to signal a lane
change while the vehicle is detected, the display changes the c olour (amber) of the warning
indicator.
BSM warning beep
The BSM warning beep is activated simultaneously with the flash ing of a BSM warning
indicator light.
▼ Cancelling Operation of Blind Spot
Monitoring (BSM)
The BSM system can be set to inoperable.
Refer to Personalisation Features on page
9-12.
When the BSM is set to inoperable, the
BSM and Rear Cross Traffic Alert
(RCTA) systems are turned off and the
BSM OFF indicator light in the instrument
cluster turns on.
NOTE
When the ignition is
switched OFF, the
system status before it was turned off is
maintained. For exampl e, if the ignition is
switched OFF while the BSM and Rear
Cross Traffic Alert (RCTA) systems are
operational, the BSM and Rear Cross
Traffic Alert (RCTA) systems remain
operational the next time the ignition is
switched ON.
When Driving
i-ACTIVSENSE
4-119
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•There are various road markings or lane markings of various shapes near an
intersection.
▼System Operation
Make sure that the LAS&LDWS OFF
indicator light in the
instrument cluster is
turned off. When the LAS&LDWS OFF
indicator light is turned on, press the
switch and make sure that the indicator
light turns off.
The LAS&LDWS indic ation (white) is
displayed in the multi-information display,
and the system goes on stand-by.
(White)
Drive the vehicle in the centre of the
vehicle lane while the system is on
standby. When all of the following
conditions are met, the LAS&LDWS
indication (green) is displayed in the
multi-information display, and the system
becomes operational.
(Green)
•The engine is running.
•The vehicle speed is about 60 km/h (37
mph) or faster.
•The system detects w hite (yellow) lane
lines on both the right and left sides.
•The driver is operating the steering
wheel.
•The driving lane is neither narrow nor
wide.

NOTE
The LAS&LDWS indication is white when
the system detects only a white (yellow)
line on either the left or right, and the
indication changes to green when the
system detects white (yellow) lines on both
the left and right sides.
Detection only on either left or right Detects on both
left and right sides
(White) (Green)
The LAS&LDWS goes on stand-by status
in the following cases:
•The system cannot detect white (yellow)
lane lines.
•The vehicle speed is less than about 60
km/h (37 mph).
•The ABS/TCS is operating.
•The TCS is turned off.
(If the TCS is turned off while the
system is operational, a warning beep is
heard and the system goes on standby.)
•The vehicle is making a sharp curve.
•The brake pedal is depressed.
•The steering wheel is operated abruptly.
When Driving
i-ACTIVSENSE
4-166
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•The driver takes his/her hands off the
steering wheel.
(The LAS&LDWS is designed to assist
the driver's steering operation and it
will resume operation automatically
when the driver holds the steering
wheel.)
•The TCS OFF switch is pressed to
cancel the TCS.
Steering operation assist OFF
(non-operational)
The steering operation assist for the
LAS&LDWS can be changed to
non-operational (OFF).
Refer to Setting Cha nge (Personalisation
Features) on page 9-12.
When the steering operation assist has
been changed to non-operational (OFF),
the operation conditions and the display of
the LAS&LDWS differ. Operate the
system as follows:
System operation
Make sure that the LAS&LDWS OFF
indicator light in the instrument cluster is
turned off. When t he LAS&LDWS OFF
indicator light turns on, press the switch
and make sure that the indicator light turns
off.
Drive the vehicle in the centre of the
driving lane while the LAS&LDWS OFF
indicator light in the instrument cluster is
turned off.
The system becomes operational when all
of the following conditions are met.
•The system detects white (yellow) lane
lines on both the right and left sides or
on either side.
•The vehicle speed is about 60 km/h (37
mph) or faster.
•The vehicle is driven on a straight road
or road with gentle curves.
•The engine is running.
The LAS&LDWS goes on stand-by status
in the following cases:
•The system cannot detect white (yellow)
lane lines.
•The vehicle speed is less than about 60
km/h (37 mph).
•The vehicle is making a sharp curve.
•The vehicle is making a curve at an
inappropriate speed.
NOTE
•The LAS&LDWS remains on stand-by
until it detects white (yellow) lines on
both the left and right sides, or on either
side.
•When the system detects a white
(yellow) lane line on one side only, the
system will not activ ate warnings for the
lane line on the side that is not being
detected.
When Driving
i-ACTIVSENSE
4-169
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

The system consists of the ASL display and the speed limiter switch on the steering wheel.

Cruise control system
MODE switch
RES/+ switch
SET- switch
OFF/CAN switch CANCEL switch RES switch
OFF switch
MODE
switch
SET- switch SET+ switch
Active Driving Display
(Windscreen Type)
(Auto Flip-up Type)
Instrument Cluster Type A
(With Multi-information Display)
(Without Multi-information Display) Instrument Cluster Type B
Mazda Radar Cruise Control (MRCC) or
Mazda Radar Cruise Control with Stop & Go
function (MRCC with Stop & Go function)
When Driving
i-ACTIVSENSE
4-175
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Adjustable Speed Limiter (ASL) Display
The setting status of the ASL is
displayed in the active driving display (vehicles with active
driving display) or the displa y in the instrument cluster.
Stand-by display
Displays when the spee d limiter switch is operated and the system is turned on.
Turns off when the system is turned off.

Active Driving Display With Multi- information DisplayWithout Multi-
information Display
Setting display
With cruise control
Displays when the SET
switch is operated
and the speed is set.
With Mazda Radar Cruise Control (MRCC) or Mazda Radar Cruise Co ntrol with
Stop & Go function (MRCC with Stop & Go function)
Displays when the SET
or SET switch is operated an d the speed is set.

Active Driving Display With Multi-
information DisplayWithout Multi-
information Display
Cancel display
Displays when any of the follo
wing operations is done and the s ystem is temporarily
cancelled.
•OFF/CAN switch is operated
•Accelerator pedal is strongly depressed

Active Driving Display With Multi- information DisplayWithout Multi-
information Display
When Driving
i-ACTIVSENSE
4-176
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Adjustable Speed Limiter (ASL) M
ain Indication (White)/Adjustable Speed
Limiter (ASL) Set Indication (Green)
The indication has two colours.
ASL main indication (white)
The indication is display in white when the MODE switch is pres sed and the ASL is
activated.
ASL set indication (green)
The indication is display in green when a speed has been set.
▼ Speed Limiter Warning Beep
Instrument cluster type A
If the vehicle speed exceeds the set speed by about 5 km/h (3 mph) or faster, the background
of the ASL set speed indication turns amber and flashes three t
imes. In addition, a warning
sound is activated at the same time. The indication stops flash ing and remains on if the
vehicle speed continues to exceed the set speed by about 5 km/h (3 mph) or faster, and the
indication and warning sound remain on until the vehicle is dri ven at the set speed or slower.
Instrument cluster type B
If the vehicle speed exceeds the set speed by about 5 km/h (3 mph) or more, a warning
sound operates continuously and the ASL display flashes at the same time. The warning
sound operates and the display flashes until the vehicle speed decreases to the set speed or
less.
Verify the safety of the surrounding area and adjust the vehicl e speed by applying the
brakes. Additionally, keep a safer distance from the vehicles b ehind you.

Active Driving Display With Multi-
information DisplayWithout Multi-
information Display
When Driving
i-ACTIVSENSE
4-177
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

4. To decrease the set speed, press the SET switch continuously. The set speed can be
adjusted in 10 km/h (5 mph) decrements. The set speed can also be adjusted in about 1
km/h (1 mph) increments by pressing the SET
switch momentary. For example, the set
speed decreases about 4 km/h (4 mph) by pressing the SET
switch 4 times.
NOTE
•(With cruise control)
When the vehicle set speed is displayed in the instrument cluster, press the RES/
switch
to set the displayed vehicle speed.
(With Mazda Radar Cruise Control (MRCC) or Mazda Radar Cruise Control with Stop
& Go function (MRCC with Stop & Go function))
When the vehicle set speed is displayed in the instrument cluster, press the RES switch to
set the displayed vehicle speed.
•The system is temporarily cancelled when the vehicle is accelerated by depressing the
accelerator pedal strongly, however, it resumes when the vehicle speed decreases to the
set speed or less.
•The vehicle speed may exceed the set speed on a down slope.
▼ Temporarily Cancelling the System
The system is temporarily cancelled (stand-by status) when any
of the following operations
is done while the ASL is displayed.
•OFF/CAN switch is pressed
•Accelerator pedal is strongly depressed
With cruise control
Press the RES/
switch to resume the operation at the previous set speed. The ASL display
remains displayed.
With Mazda Radar Cruise Control (MRCC) or Mazda Radar Cruise Co ntrol with
Stop & Go function (MRCC with Stop & Go function)
Press the RES switch to resume the operation at the previous se t speed. The ASL display
remains displayed.
NOTE
•(With cruise control)
The set speed can be set by pressing the SET
switch while the system is in stand-by
status.
(With Mazda Radar Cruise Control (MRCC) or Mazda Radar Cruise Control with Stop
& Go function (MRCC with Stop & Go function))
The set speed can be set by pressing the SET
or SET switch while the system is in
stand-by status.
•The ASL is not cancelled by depressing the brake pedal.
When Driving
i-ACTIVSENSE
4-180
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Radar Sensor (Front)*
Your vehicle is equipped with a radar sensor (front).
The following systems also use the radar sensor (front).
•Mazda Radar Cruise Control (MRCC)
•Mazda Radar Cruise Control with Stop & Go function (MRCC with S top & Go function)
•Distance Recognition Support System (DRSS)
•Smart Brake Support (SBS)
The radar sensor (front) functions by detecting the radio waves reflected off a vehicle ahead
or an obstruction sent from the radar sensor.
The radar sensor (front) is mo unted behind the front emblem.
Radar sensor (front)
If “Front radar blocked” is displayed in the multi-information display of the instrument
cluster, clean the area around the radar sensor (front).
CAUTION
Heed the following precautions to a ssure correct operation of each system.
 Do not adhere stickers (including transparent st ickers) to the surface of the radiator grille
and front emblem in and around the radar sens or (front), and do not replace the radiator
grille and front emblem with any product that is not a genuine product designed for use
with the radar sensor (front).
 The radar sensor (front) includes a function fo r detecting soiling of the radar sensor's front
surface and informing the driver, however, depending on the conditions, it may require
time to detect or it may not detect plastic sh opping bags, ice or snow. If this occurs, the
system may not operate correctly, therefore al ways keep the radar sensor (front) clean.
 Do not install a grille guard.
 If the front part of the vehicle has been dama ged in a vehicle accident, the position of the
radar sensor (front) may have moved. Stop the system immediately and always have the
vehicle inspected at an Authorised Mazda Repairer.
When Driving
i-ACTIVSENSE
*Some models.4-201
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2