2017 MAZDA MODEL CX-5 height adjustment

Front Seat
▼Seat Operation
Power operation
Seat Slide
(Manual Seat)
To move a seat forward or backward, raise the lever and slide t he seat to the desired position
and release the lever.
Make sure the lever returns to i ts original position and the seat is locked in place by
attempting to push it forward and backward.
(Power Seat)
To slide the seat, move the slide lifter switch on the outside of the seat to the front or back
and hold it. Release the sw itch at the desired position.
Height Adjustment*
(Manual Seat)
To adjust the seat height, move the lever up or down.
(Power Seat)
To adjust the seat height, move the switch up or down.
Height Adjustment for Front Edg e of Seat Bottom (Driver's Power Seat)
To adjust the front height of the seat bottom, raise or lower t he front of the slide lifter
switch.
Essential Safety Equipment
Seats
*Some models.2-5
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Do not use the seat warmer even when
taking a short nap in the vehicle:
The seat may be heated excessively and
cause a low-temperature burn.
Do not place heavy objects with sharp
projections on the seat, or insert needles or
pins into it:
This could cause the seat to become
excessively heated and result in injury from
a minor burn.
CAUTION
Do not use organic solvents to clean the
seat. It may damage the seat surface and
the heater.
NOTE
•If the ignition is switched off while the
seat warmer is operating (High, Mid or
Low) and then switched ON again, the
seat warmer will automatically operate
at the temperature set before switching
off the ignition.
•Use the seat warmer when the engine is
running. Leaving the seat warmer on for
long periods with the engine not running
could cause the battery power to be
depleted.
•The temperature of the seat warmer
cannot be adjusted beyond High, Mid
and Low because the seat warmer is
controlled by a thermostat.
▼Driving Position Memory*
The desired driving position can be called
up after programming the position.
The following driving positions can be
programmed.
•Driver’s seat position (seat slide, height
adjustment, front edge of seat bottom,
seat recline)
Refer to Seat Operation on page 2-5.
•Active driving display (display position,
brightness level, display information)
Refer to Active Driving Display on page
4-39.
CAUTION
Do not place
fingers or hands around the
bottom of the seat while the seat memory
function is operating. The seat moves
automatically while the seat memory
function is operating and fingers or hands
could get pinched and injured.
SET button
1
2
The driving position can be programmed
or operated using the buttons on the side
of the seat or the key.
NOTE
•Lumbar support adjustment cannot be
programmed.
•Individual seat positions can be
programmed to the two available
programming buttons on the side of the
driver's seat, plus one seat position for
each registered key.
Essential Safety Equipment
Seats
*Some models.2-7
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•When the engine is stopped while the
seat warmers are operating and then the
ignition is switched ON, the seat
warmers will not turn back on
automatically. In addition, the seat
warmer operation stops automatically
after the seat warmers have operated for
about 90 minutes.
To turn the seat warmer back on, press
the switch.
•The temperature of the seat warmer
cannot be adjusted beyond High, Mid
and Low because the seat warmer is
controlled by a thermostat.
▼Armrest*
The rear armrest in the centre of the rear
seatback can be used (no occupant in the
centre seat) or placed upright.

WA R N I N G
Never put your hands and fingers around
the moving parts of the seat and armrest:
Putting your hands and fingers around the
moving parts of the seat and armrest is
dangerous as they could get injured.
Head Restraints
Your vehicle is equipped with head
restraints on all outboard seats and the rear
centre seat. The head restraints are
intended to help protect you and the
passengers from neck injury.
WA R N I N G
Always drive with the head restraints
installed when seats are being used and
make sure they are properly adjusted. In
addition, always raise the head restraints
on the rear outboard seats when they are
being used:
Driving with the head restraints adjusted
too low or removed is dangerous. With no
support behind your head, your neck could
be seriously injured in a collision.
▼Height Adjustment
Adjust the head restra
int so that the centre
is even with the top of the passenger's
ears.

To raise a head restraint, pull it up to the
desired position.
To lower the head restraint, press the
stop-catch release, then push the head
restraint down.
Essential Safety Equipment
Seats
*Some models.2-15
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Front-facing type
WARNING
Never install a front-facing child seat in the
wrong seat position:
Installing a front-facing child seat without
System Suitability for Various Seat
Positions” is dangerous. A front-facing
child seat installed in the wrong seat
position cannot be properly secured. In a
coll ision, the child could hit something or
someone in the vehicle and be seriously
injured or even killed.
Do n ot install a front-facing child-re straint
system on the front pa ssenger seat unless it
is unavoid able:
In a collision, the force of a deploying air
bag could cause serious injury or death to
the child. If installing a front-facing
child-restraint system on the front
passenger seat is unavoidable, move the
front passenger seat as far back as possible
and adjust the seat bottom (height
adjustable seat bottom) to the highest
position at which the seat belt fastening
the child-restraint system is securely
tightened.
Junior Seat Installation Position
A junior sea t is used in the front-facing
pos ition only.
If a junior seat with a removable backr est
is used, usin g the j unior s eat with the
b ack rest ins talled is recommended.

Refer to the table, “Child-Restraint System
Suitabil ity for Various S eat Positions” for
junior seat inst allation pos ition (page 2-
34).
WARNING
Always inst all a junior se at in the co rrect
seat position:
Installing a junior seat without
consulting the table “Child-Restraint
System Suitability for Various Seat
Positions” is dangerous. A junior seat
installed on the wrong seat position cannot
be properly secured. In a collision, the child
could hit something or someone in the
vehicle and be seriously injured or even
killed.
Essential Safety Equipment
Child Restraint
2-32
2017-6-7 7:51:19Form No. CX-5 8FY4-EE-17E+L_Edition2
We recommend the use of the junior seat
with backrest to allow simple adjustment
of the shoulder belt position and to give
your child the best protection.

•Cruise Control Operation Conditions
Refer to Cruise Control on page 4-207.
•Navigation Guidance (vehicles with navigation system)
•Speed limit indicator (vehicles with navigation system)
•Vehicle Speed
Each setting/adjustment for the active driving display can be p erformed on the centre
display.
1. Select the
icon on the home screen and display the Settings screen.
2. Select the AD-Disp tab.
3. Select the desired item and perform the setting/adjustment.
•Method for adjusting screen brightness (automatically/manually)
•Screen brightness initial settings (automatic adjustment is sel ected)
•Screen brightness adjustment (manual adjustment is selected)
•Display position of active driving display (display height)
•Active driving display angle adjustment (display angle correcti on) (With windscreen
type)
•Active driving display ON/OFF (indication)
•Navigation guidance ON/OFF
•Reset settings (reset)
NOTE
•The desired driving position (display position, brightness level, display information) can
be called up after programming the position.
Refer to Driving Position Memory on page 2-7.
When Driving
Instrument Cluster and Display
4-41
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

ItemFeatureFactory Set-
ting Available Set-
tings Settings
Change
Method
Active Driving Display (page 4-39)
Display Setting can be changed so that the Active Driv-
ing Display is not displayed.
On On/Off C ―
The display height (up/down position) can be
changed.
013 steps up/
down from ini-
tial setting (total: 27 steps) C―
The method for adjusting the display bright-
ness (automatically/manually) can be changed.
AUTOAUTO/
MANUAL C―
The standard brightness with the automatic
brightness adjustment can be changed. 02 steps up/down
from initial set- ting (total: 5
steps) C―
The standard brightness with the manual
brightness adjustment can be changed.
020 steps up/
down from ini-
tial setting (total: 41 steps) C―
The display angle can be changed.
03steps up/down
from initial set- ting (total:7steps) C―
Navigation guid-
ance
Display/non-display
On On/Off C ―
*1 Though these systems can be turned Off, doing so will defeat the purpose of the system and Mazda
recommends that these systems remain On.
*2 Only the volume of the warning beep during Blind Spot Monitori ng (BSM) operation can be changed. The
volume of the warning beep durin g Rear Cross Traffic Alert (RCTA) operation cannot be changed.
*3 This system functions only when t he navigation system is functioning.*4 If the auto-wiper control is set to Off, the wiper lever position is set to in termittent operation.*5 The operation may stop in 15 mi nutes due to the effect of the outside temperature even if the operation time of
the rear window defogger has been changed to Continuous.
*6 Available only in display from the centre display.
Specifications
Personalisation Features
9-18
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2