2017 MAZDA MODEL CX-5 instrument cluster

The vehicle speed preset using the cruise
control is displayed in the instrument
cluster.
Type A Instrument Cluster
Type B Instrument ClusterEuropean model
Except European model Multi-information Display
Active Driving Display
▼To Increase Cruising Speed
Follow either of these procedures.
To increase speed using cruise control
switch
Press the RES/ switch and hold it. Your
vehicle will accelerate. Release the switch
at the desired speed.

Press the RES/
switch and release it
immediately to adjust the preset speed.
Multiple operations will increase the
preset speed according to the number of
times it is operated.
Increasing speed with a single RES/
switch operation
Instrument cluster d isplay for vehicle
speed indicated in km /h: 1 km/h (0.6 mph)
Instrument cluster d isplay for vehicle
speed indicated in mph: 1 mph (1.6 km/h)
To increase speed using accelerator
pedal
Depress the accelerator pedal to accelerate
to the desired speed. Press the SET
switch and release it immediately.
NOTE
Accelerate if you want to speed up
temporarily when the cruise control is on.
Greater speed will not interfere with or
change the set speed. Take your foot off
the accelerator to retu rn to the set speed.
▼To Decrease Cruising Speed
Press the SET switch and hold it. The
vehicle will gradually slow.
Release the switch at the desired speed.

Press the SET
switch and release it
immediately to adjust the preset speed.
Multiple operations will decrease the
preset speed according to the number of
times it is operated.
Decreasing speed with a single SET
switch operation
Instrument cluster d isplay for vehicle
speed indicated in km /h: 1 km/h (0.6 mph)
Instrument cluster d isplay for vehicle
speed indicated in mph: 1 mph (1.6 km/h)
When Driving
Cruise Control
4-210
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Tyre Pressure Monitoring System*
The Tyre Pressure Monitoring System (TPMS) monitors the pressure for each tyre.
If tyre pressure is too low in one or more tyres, the system wi ll inform the driver via the
warning light in the instrument cluster and by the warning beep sound.
Refer to Warning Indication/Warning Lights on page 4-42.
Refer to Tyre Inflation Pressu re Warning Beep on page 7-66.

The tyre pressure sensors installed on each wheel send tyre pressure data by radio signal to
the receiver unit in the vehicle.
Tyre pressure sensors
NOTE
When the ambient temperature is low due to seasonal changes, tyre temperatures are also
lower. When the tyre temperature decreases, the air pressure decreases as well. The TPMS
warning light may illumina te more frequently. Visually inspect the tyres daily before driving,
and check tyre pressures monthly with a tyre pressure gauge. When checking tyre pressures,
use of a digital tyre pressure gauge is recommended.

TPMS does not alleviate your need to check the pressure and con dition of all four tyres
regularly.
CAUTION
 Each tyre, including the spare (if provided), should be checked monthly when cold and
inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle
placard or tyre inflation pressure label. (If your vehicle has tyres of a different size than the
size indicated on the vehicle placard or tyre inflation pressure label, you should determine
the proper tyre inflation pressure for those tyres.)
When Driving
Tyre Pressure Monitoring System
4-212*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and anticlockwise for
cold.
•When the DUAL switch is off:
Turn the driver temperature control dial
to control the temperature throughout
the entire cabin.
•When the DUAL switch is on:
Turn the driver or front passenger
temperature control dial to
independently control the temperature
on each side of the cabin.
NOTE
•The air-conditioning system changes to
the individual operation mode (DUAL
switch indicator light illuminated) by
turning the front passenger temperature
control dial even when the DUAL switch
is off, which allows individual control of
the set temperature for the driver and
front passenger.
•The temperature units for the
temperature setting display can be
changed in conjunction with the
temperature units for the outside
temperature display.
(Type A instrument cluster)
Refer to Outside Temperature Display
on page 4-35.
(Type B instrument cluster)
Refer to Outside Temperature Display
(Without Multi-information display) on
page 4-27.
Fan control switch
The fan has seven speeds. The selected
speed will be displayed.
Mode selector switch
The desired airflow mode can be selected
(page 5-6).
NOTE
•With the airflow mode set to the
position and the temperature control
dial set at a medium temperature,
heated air is directed to the feet and air
at a comparably lower temperature will
flow through the central, left and right
vents.
•To set the air vent to , press the
windscreen defroster switch.
•In the position, the outside air
position is automatically selected.
A/C switch
Pressing the A/C swit ch while the AUTO
switch is turned on w ill turn off the air
conditioner (cooling/dehumidifying
functions).
The on/off of the air conditioner switches
each time the A/C switch is pressed.
Changes as follows each time the A/C
switch is pressed.
A/C→A/C ECO→Stop
NOTE
•The air conditioner operates when the
A/C switch is pressed while the air
conditioner is turned off.
•The A/C ECO function is designed to
economize use of the air-conditioning
system. “A/C ECO” is displayed to
indicate that the ai r-conditioning system
is operating at optimum control.
•The air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).
Interior Features
Air-Conditioning System
5-12
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

*3 Flexible setting is factory preset for some countries in Europ e. Consult an Authorised Mazda Repairer for
details. Flexible setting can be s et if the vehicle is operated mainly where none of the following conditions
apply.
a) Purpose of vehicle use is poli ce car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
Once the flexible maintenance is selected, the vehicle calculat es the remaining oil life based on engine
operating conditions and lets you know when an oil change is du e by illuminating the wrench indicator light in
the instrument cluster.
Reset the engine oil data wheneve r replacing the engine oil regardless of the message/wrench indicator light
display.
*4 If the vehicle is operated primarily under any of the followin g conditions, replace the engine oil and oil filter at
every 10,000 km (6,250 miles) or shorter.
a) Purpose of vehicle use is poli ce car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
d) Driving for long period in cold temperatures or driving regul arly at short distance only
e) Driving in extremely hot conditions
f) Driving in mountainous conditions continually
*5 If the vehicle is operated primarily under any of the followin g conditions, replace the engine oil and oil filter at
every 5,000 km (3,125 miles) or 6 months.
a) Purpose of vehicle use is poli ce car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
d) Driving for long period in cold temperatures or driving regul arly at short distance only
e) Driving in extremely hot conditions
f) Driving in mountainous conditions continually
*6 For SKYACTIV-D 2.2, r eset the engine oil data whenever replaci ng the engine oil regardless of the message/
wrench indicator light display.
*7 Implement the fuel injection amount correction.*8 Drain water in the fuel system if the indicator lights is ON.*9 Also inspect the air conditioner drive belts, if installed.
If the vehicle is operated primarily under any of the following conditions, inspect the drive belts at every
20,000 km (12,500 miles) or 12 months .
a) Driving in dusty conditions
b) Extended periods of idling or low speed operation
c) Driving for long period in col d temperatures or driving regularly at short distance only
d) Driving in extremely hot conditions
e) Driving in mountainous conditions continually
*10 Use of FL-22 is recommended wh en replacing engine coolant. Using engine coolant other than FL-22 may
cause serious damage to the engine and cooling system.
*11 Inspect the battery electrolyte level, specific gravity and o uter appearance. The sealed battery only requires an
outer appearance inspection.
*12 If the brakes are used extensi vely (for example, continuous hard driving or mountain driving) or if the vehicle
is operated in extreme ly humid climates, replace the brake flui d annually.
*13 If this component has been submerged in water, the oil should be replaced.*14 Tyre rotation is recommended every 10,000 km (6,250 miles).*15 Check the tyre repair fluid expiration date every year when performing the periodic maintenance. Replace the
tyre repair fluid bottle with new one before the expiration date.
Maintenance and Care
Scheduled Maintenance
6-5
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Maintenance IntervalNumber of months or kilometres, whichever comes first.
Months 12 24 36 48 60 72 84 96 108 120 132 144
×1000 km 15 30 45 60 75 90 105 120 135 150 165 180
Cabin air filter (if installed) RRRRRR
Tyres (including spare tyre) (with inflation pres-
sure adjustment)
*11IIIIIIIIIIII
Emergency flat tyre re pair kit (if installed)
*12Inspect annually.
Chart symbols:
I: Inspect: Inspect and clean, re pair, adjust, fill up, or replac e if necessary.
R: Replace
C: Clean
T: Tighten
L: Lubricate
Remarks:
*1 Also inspect the air conditi oner drive belts, if installed.
If the vehicle is operated primarily under any of the following conditions, inspect the drive belts at every 7,500
km or 6 months.
a) Driving in dusty conditions
b) Extended periods of idling or low speed operation
c) Driving for long period in col d temperatures or driving regularly at short distance only
d) Driving in extremely hot conditions
e) Driving in mountainous conditions continually
*2 Flexible setting can be set if the vehicle is operated mainly where none of the following conditions apply.
a) Purpose of vehicle use is poli ce car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
The vehicle calculates the rem aining oil life based on engine o perating conditions and lets you know when an
oil change is due by illuminating the wrench indicator light in the instrument cluster.
Replace the engine oil and filter when message/wrench indicator light is ON. And they must be changed at
least once a year or within 15,000 km since last engine oil and filter change.
The system must be reset whenever replacing the engine oil regardless of the message/wrench indicator light
display.
*3 If the vehicle is operated primarily under any of the followin g conditions, replace the engine oil and oil filter at
every 7,500 km or 6 months.
a) Purpose of vehicle use is poli ce car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
d) Driving for long period in cold temperatures or driving regul arly at short distance only
e) Driving in extremely hot conditions
f) Driving in mountainous conditions continually
Maintenance and Care
Scheduled Maintenance
6-9
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

*2 Flexible setting can be set if the vehicle is operated mainly where none of the following conditions apply.
a) Purpose of vehicle use is police car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idli ng or low speed operation
The vehicle calculates the remaining oil life based on engine o perating conditions and lets you know when an
oil change is due by illuminating the wrench indicator light in the instrument cluster.
Replace the engine oil and filter when message/wrench indicator light is ON. And they must be changed at
least once a year or within 10,00 0 km since last engine oil and filter change.
The system must be reset whenever replacing the engine oil rega rdless of the message/wrench indicator light
display.
*3 If the vehicle is operated prim arily under any of the following conditions, replace the engine oil and oil filter at
every 5,000 km or 6 months.
a) Purpose of vehicle use is police car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idli ng or low speed operation
d) Driving for long period in cold temperatures or driving regul arly at short distance only
e) Driving in extremely hot conditions
f) Driving in mountainous conditions continually
*4 For SKYACTIV-D 2.2, reset the e ngine oil data whenever replacing the engine oil regardless of the message/
wrench indicator light display.
*5 Implement the fuel injection amount correction.*6 If the vehicle is operated in v ery dusty or sandy areas, clean the air filter at every 5,000 km or 6 months.*7 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may
cause serious damage to the engine and cooling system.
*8 Inspect the battery electrolyte level, specific gravity and outer appearance. The sealed battery only requires an
outer appearance inspection.
*9 If the brakes are used extensively (for example, continuous ha rd driving or mountain driving) or if the vehicle
is operated in extremely humid c limates, replace the brake fluid annually.
*10 If this component has been submerged in water, the oil should be replaced.*11 Tyre rotation is recommended every 10,000 km.*12 Check the tyre repair fluid e xpiration date every year when performing the periodic maintenance. Replace the
tyre repair fluid bottle with new one before the expiration date.

Maintenance and Care
Scheduled Maintenance
6-12
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Maintenance Monitor
▼Maintenance Monitor (Type A audio)
“Oil Change” with flexible setting*1 is available. Consult an Au
thorised Mazda Repairer for
details
*2. When the engine oil flexible maintenance setting is selected, the wrench indicator
light in the instrument cluster w ill be illuminated when remaining oil life becomes less than
1,000 km (600 mile), or remaining days are less than 15 (Whiche ver comes first).
Reset method
Press and hold the instrument panel illumination knob with the ignition switched off, then
switch it on. Keep pressing the instrument panel illumination k nob for more than 5 seconds.
The master warning light will flash for a few seconds when the reset is completed.
Instrument panel illumination knob
*1 The engine oil flexible maintenance setting is available (only some models). Based on
the engine operating conditions, the onboard computer in your v ehicle calculates the
remaining oil life.
*2 When the engine oil flexible maintenance setting is selected, the system must be reset
whenever replacing the engine oil regardless of the wrench indi cator light display.
Maintenance and Care
Scheduled Maintenance
6-17
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Maintenance Monitor (Type B audio)
1. Select the icon on the home screen to display the “Applications” screen.
2. Select “Vehicle Status Monitor”.
3. Select “Maintenance” to display the maintenance list screen.
4. Switch the tab and select the setting item you want to change .
You can customize settings in the setup display as follows:
Ta b I t e m E x p l a n a t i o n
Scheduled Setting
Notification can be switched on/off.
Time (months) Displays the time or distance until maintenance is due.
Select this item to set the maintenance period.
The wrench indication/indicator light in the instrument cluster
will be illuminated when the remaining distance is less than 1, 000
km or 600 mile, or the remaining number of days is less than 15
(whichever comes first).
Distance (km or mile)
Reset
Resets the time and distance to the initial values.
Once the system turns on, it needs to be reset whenever carrying
out maintenance.
Tyre Rotation Setting
Notification can be switched on/off.
Distance (km or mile) Displays the distance until tyre rotation is due.
Select this item to set the tyre rotation distance.
The wrench indication/indicator
light in the instrument cluster
will be illuminated when the remaining distance is less than 1, 000
km or 600 mile.
Reset Resets the remaining distance to the initial value.
Once the system turns on, it need
s to be reset whenever rotating
the tyres.
Oil Change Setting
*1Notification can be switched on/off.
Distance (km or mile) Displays the distance until
the oil replacement is due.
Select this item to set the oil replacement distance.
The wrench indication/indicator light in the instrument cluster
will be illuminated when the remaining distance is less than 1, 000
km or 600 mile.
Reset
*2Resets the remaining distance to the initial value.
Once the system turns on, it need s to be reset whenever replacing
the engine oil.
*1 The engine oil flexible mainten ance setting is available (only some models). Consult an Authorised Mazda
Repairer for details.
When the engine oil flexible mai ntenance setting is selected, you will see the following items in the display.
The vehicle calculates the remaining oil life based on the engi ne operating conditions and lets you know when
an oil change is due by illuminating the wrench indicator light in the instrument cluster.
*2 Whenever the engine oil is replaced, the vehicle engine control unit reset is necessary for SKYACTIV-D 2.2.
Your Authorised Mazda Repairer will be able to reset the engine control unit or refer to the vehicle engine
control unit reset procedure on page 6-27.
Maintenance and Care
Scheduled Maintenance
6-18
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2