2017 AUDI Q3 light

Instruments and indicator lights
If the message does not turn off, have an author ­
ized Audi dealer or authorized Audi Service Facili­
ty repa ir the malfunction .
t Safety belt
The. indicator light stays on unti l the driver's
and front passenger's safety be lts are fastened.
Above a certain speed, there will also be a warn­
ing tone .
(D Tips
For addit ional information on safety be lts,
see
¢ page 109.
@ -Steering lock
• Steering fau lt! Do not dri ve vehicle!
There is a malfunction in the electronic steering
lock . You cannot turn the ignition on.
Do
not tow your vehicle because it cannot be
steered. See an authorized Audi dealer or author­
ized Audi Service Fac ility for assistance.
ell Steering lock: System fault! Ple ase contact
dealer.
There is a malfunc tion in the electronic steering
lock .
D rive to an a uth o rized Aud i dea le r or a uth orized
Aud i Serv ice Fa cility immediately to have t he
malfunct io n corre cted .
A WARNING
Do not tow your veh icle when the re is a mal ­
function in the electronic stee ring lock - this
increases the risk of an accident.
;;.! [J Electronic Stabilization Control (ESC)
If the bl indicator light blinks wh ile driving, the
ESC or ASR (Anti-Slip Regu lation) is actively regu­
lating.
If the
bl indicato r light turns on, the system has
sw itched the ESC off. In this case, you can switch
the ignition off and then on to switch the ESC on
again . The indicator light turns off when the sys­
tem is functioning fully.
14
If the II ind icator light turns on, ESC was
switched off using the
I ~ OF FI button
¢ page 92.
Stabilization con trol (ESC / ABS ): Fault! See
owne r's manual
If the GJ ind icator light and the ABS indicato r
li gh t
[El (U SA mode ls) I [iJ (Canada models)
turn on an d this message appears, there is a mal­
f unction in the ABS system or electronic differen ­
tia l lock. This also causes the ESC to malfunction.
The brakes still function with their normal power,
but ABS is not active.
Drive to an au thorized A udi dealer or authori zed
Audi Se rvice Facility immediate ly to have the
malfunction corrected .
A WARNING
If the 1111 (USA models) • (Canada mod­
e ls) brake system indicator light turns on to­
gether with the ABS and ESC ind icator lights,
the ABS and ESC regulating function may have malfunctioned . Funct ions that stab ilize
the vehicle are no longer availab le. This co uld
cause the vehicle to swerve, which in cr eases
the r is k that the vehicle will slide . Dr ive care­
fu lly to the nearest authorized Audi dealer or
authorized Audi Service Facility and have the malfunction corrected.
(D Tips
For addi tional in format ion on ESC and ABS,
refer to¢
page 92.
!J..' Safety systems
The E,i indicator lig ht monitors the safety sys­
tems.
If the
E,i ind icator light turns on or blinks, there
i s a ma lfunction in a safety system.
D rive to an author ized A udi dealer or authori zed
Audi Se rvice Fac ility immed iate ly to have the
malfunction corrected.

00
00
......
"' ,....
"' ...... 0 0 :::,
00
A WARNING , ~ -
Have the malfunction in the safety systems
inspected immediately. Otherwise, there is a
r isk that the systems may not activate during
a collision, which increases the risk of serious
injury or death.
(0) Brake pads
Ei] Brake pad s!
The brake pads are worn .
Drive to an authorized Aud i dea ler or authorized
Audi Service Facility immediately to have the brake pads checked.
App lies to: USA models
The Ei] indicator light turns on together with the
1111 indicator light
EPC Engine control (gasoline engine)
Applies to: vehicl es with gasoline engines
If the 13:a indicator light turns on while driving,
there is an eng ine control malfunction.
Immediately drive slowly to an authorized Audi
dealer or authori zed Audi Service Facility to have
the malfunction corrected.
0 Malfunction indicator lamp (MIL)
The malfunction indicator lamp (MIL) is part of
the On Board Diagnostic system (OBD II). The
¢4 symbol turns on when the ign ition is switched
on and turns off again once the e ngine is started
and running at a steady id le speed . This indicates
that the MIL is functioning correctly.
The indicato r light turns on if there is a malfunc­
tion in the engine electronics. See an autho rized
Audi dealer or authorized Audi Service Facility to
have the ma lfunction corrected. For additiona l
information, see
~ page 17.
The indicator light can also turn on if the f uel fill­
e r cap is not closed correct ly
i::!> page 157.
Instruments and indicator lights
!"-" , Engine speed lim itation
Applies to: vehicles with engine speed limitation
(I! Maximum engine speed XXXX RPM
The engine speed is automatically limited to the
speed displayed in the driver information system.
This protects the engine from overheat ing .
The engine speed limitation deactivates once the engine is no longer in the critical temperature
range and you have released the accelerator ped­
al once .
If the engine speed limitation was activated by
an engine control malfunction, the
13:a in dicator
light also turns on. Make sure that the speed
does not go above the speed displayed . Dr ive to
an authorized Aud i dea le r or authorized Audi
Service Facility immed iately to have the malfunc­
tion corrected.
~;. Engine oil
Ill Check oil level.
Refill engine oil as soon as possible i::!>page 162.
~ .,. Engine oil sensor
• Oil level sensor: System fault!
The sensor to check the eng ine o il level has
failed. Drive to an authorized Audi dealer or au­
thorized Aud i Serv ice Facility immediately to have
the malfunction cor rected.
i) Tank system
H Please refuel
If the indicator l ight turns on for the first time
and the message appears, there are about
1.8 -2.2 gallons ( 7.0 -8. S liters) of fuel left in the
tank .
H Fuel tank system malfunction! Contact deal­
er
Drive to an authorized Audi dealer or authorized
Audi Service Facility immed iately to have the
malfunction corrected. ..,.
15

Instruments and indicator lights
(D Tips
More informat ion on ref ueling is ava ila ble on
page
c::> page 156.
c:> Washer fluid level
A pp lies to: ve hicles w ith was her flu id level indicato r
Ill Please refill washer fluid
Fill the washer fluid with the ignition switched
off
c::> page 169.
~ Engine start system
i ·I 1-'.ngine start system: Malfunction! Please
contact dealer.
Do not switch the ignition off because you may
not be able to switc h it on aga in.
D rive to an a uth o riz e d Aud i de aler or a uth o riz ed
Aud i Serv ice Facility immedia tely to have the
malfunctio n corrected .
Engine start sy stem: Malfun ction . Plea se con ­
tact dealer .
There is a malfunc tion in the eng ine start ing sys­
tem.
Drive to an a uthorized Aud i dea ler or authorized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
i§i Defective light bulb warning
If th e 1:J indica to r li ght turns on, a b ulb has
fa iled. The mess age in dicat es th e loca tion of the
bu lb .
Re plac e t he bulb immedia tely.
Vehicle lights: system fault!
There is a malfunction in the head lights or the
light switch.
D rive to an a uth o rized Aud i de aler or a uthorized
Aud i Serv ice Facility immediately to have t he
malfunct io n corrected .
16
A WARNING
-
-Light bulbs a re under p ressure and can ex­
plod e when b ulbs are replaced, wh ic h in ­
creases the risk of i nju ry .
- With HID headlights (xenon headlights) , the
high-vo ltage component must be handled
correctly . O th erwise, there is a r is k of fa tal
ln JUr y.
i.ID Headlight range control
II Headlight range control sy stem: system
fault!
There is a ma lf u nction in the headlight range
contro l system, which may cause gla re for other
drive rs.
Drive to an author ized A udi dealer or authorized
Audi Se rvice Facil ity immed iate ly to have the
malfunction correc ted.
go Audi adaptive light
App lies to: vehicles wi th Audi ada ptive light
r!iJ Audi adaptive light : system fault!
-
There is a ma lfunction in the adap tive lights. The
headlig hts st ill funct ion.
D rive to an authorized A udi dealer or authorized
Audi Se rvice Facility immediate ly to have the
malfunction corrected .
@.D Light/rain sensor
App lies to: vehicles wit h lig ht/ra in sensor
£1 Automatic headlights /wipers: System fault!
The light/rain sensor is malfunctioning.
The low beams remain sw itched on at all times
fo r safety reasons when the light switch is in the
AUTO position. Yo u can cont in u e to turn the
li ghts on and off us ing the lig ht switch. You can
sti ll contro l all fu nctions that are i ndependent of
the rain senso r thr ough the winds hield wiper lev­
e r.
D rive to an authorized A udi dealer or authorized
Audi Service Facility immediate ly to have the
malfunction correc ted.

a:,
a:,
...... N r--. N .... 0 0 ::, a:,
; Adaptive dampers
App lies to: vehicles with Audi drive select and suspension con­
tro l
B Suspen sion: system fault !
There is an adaptive damper malf unction .
Drive to an aut hori zed Aud i dea le r o r a uthori zed
Audi Service Facility immediately to have the
malfunct ion corrected.
¢¢ Turn signals
If the II or i!I indicator light b links, the turn
signals are activated. If both indicator lights are
blinking, the emergency flashers are act ivated.
If an indicato r light blinks twice as fast as usua l,
a t urn signa l bulb has failed . Caref ully drive to an
author iz ed Audi dealer or author iz ed Audi Service
Facility immediately to have the malfunction cor­
rected.
¢1.~ Trailer turn signal assembly
The indica to r li ght II blinks when the turn sig­
n a l is used , if a traile r h as been p roperly connec t­
e d to the veh icle .
If one of the turn s ignal bulbs on the trailer is
bu rned out or defect ive, the indicator l igh t will
n o t bl ink when yo u use the tu rn s ign als.
(D Tips
For ve hicles with a trail er hitch that was in­
s talle d later accord ing to fa ctory spec ifica­
ti ons, the trailer tur n signal as sembly is actu ­
at ed.
/fJl~/c:5 Door , hood or luggage
compartment lid is open
IJ-If the ind icator light tu rns on, then one of
the doors is not closed.
&-\-If the ind icator light t urns on, then the hood
is not closed .
§-j-If the ind icator light tu rns o n, then the lug­
g age compartment lid is not closed .
Instruments and indicator lights
On Board Diagnostic
System (OBD)
Malfunction indicator lamp (MIL)
The ma lf u nction ind icator lamp (MI L) Ill in t he
inst rument cluste r is pa rt of the On Board D iag­
nostic System (OBD II).
T he w arning/i ndic ator lig ht tu rn s o n when the ig ­
nition is switche d on and tu rns off once the en­
gine is starte d and is running in idle at a stab le
speed. This indicates t hat the MIL is f unctioning
correctly.
If the light does not turn off after starting the
engine
or t urns on while driving, this may ind i­
cate there is a malfunction in the eng ine. If the
i ndicator tu rns on, the catalytic conve rter may be
damaged .
Drive
with reduced engine performance (avo id
high speeds for extended periods of t ime and/o r
fast acceleration) and have the malfu nction cor­
rected . See an author ized Audi dealer or author ­
ized Audi Service Facility .
The indicator may turn on if the e lectronic speed
limiter is faulty . For addit ional information, see
¢ page 18, Electronic speed limiter .
The MIL may also turn on if the fuel filler cap is
not closed correctly ¢
page 157.
On-Board Diagnostics
Fig. 5 Locat ion o f Data Link Connecto r (OLC)
On -Board Diagnostics mo nitors the components
of your emission control system . Each monitore d
I>-
17

Instruments and indicator lights
component in your engine system has been as ­
signed a code. In case of a ma lfunction, the com­
ponent w ill be identif ied and the fau lt stored as a
code in the control module memory.
The MI L light may a lso ill uminate if there is a
leak in the on-board f uel vapor recovery system.
If the light ill uminates after a refueling, stop the
veh icle and make sure the fuel filler cap is prop­
erly closed (on ly vehicles with gasoline engine)
¢ page 157 .
In order to make an accurate d iagnosis, the stor­
ed data can on ly be displayed using special diag­
nostic equipment (generic scan too l for 0BD) .
In order to connect the specia l diagnostic equip ­
ment, p ush the plug into the Data Link Connector
(DLC). The DLC is located to the right of the hood
release ¢
fig. 5.
Your authorized Audi dealer or qualified work­
shop can interpret the code and perform the nec­
essary repair.
A WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a colli­
sion!
Electronic speed limiter
Your veh icle may be facto ry equipped with ti res
that are r ated for a maxim um speed of 130 mph
(210 km/h) . This is less than the maxim um speed
of yo ur vehicle. To reduce the risk of sudden tire
fa ilur e and loss of control if the veh icle is operat­
ed at excessive speeds, your vehicle a lso has an
electronic speed limiter. The electronic speed lim iter prevents your vehicle from going faster
than the t ire speed rating . For more information
¢ page 171 .
If the engine contro l unit receives faulty vehicle
ro ad speed s ignals, the Malfunction Indicator
Lamp (MIL)
¢4 will illum inate . If this occurs,
contact the nearest authorized Audi dealer for
assistance .
18
A WARNING
--
Always observe the posted speed limits and
adjust your speed to suit preva iling road, traf­
fic and weather conditions. Never drive your
vehi cle faster than the maximum speed rating
of the ti res insta lled.

a:,
a:,
...... N r--. N
'"' 0 0 ::, a:,
Driver information
system
Overview
Applies to: ve hicles with driver information system
Fig. 6 Display on vehicles w it h driver information system
and mu ltifunction steering w heel*
~ N
0
::) CX) al
Driving information and vehicle settings are
shown in the instrument cluster display. The type
of display and the contents depend on the vehicle
eq uipment.
Depending on the vehicle equipment, the driver
information system is controlled with either the
buttons on the windshield wiper lever*
i::> page 19or with the buttons on the mult i­
function steering wheel*
c:> page 19.
On vehicles w ith a multifunction steering wheel*,
the information @ is shown in tabs @. The tabs
are visible as soon as yo u press a button on the
multifunction steering wheel*.
The instrument cluster display provides informa­
tion about :
® Time and date c:> page 9
Digita l speedometer
On -board computer
i::> page 20
Efficiency program ¢page 21
Reduced display *
Indicator lights and messages
¢page 10
Service interval display c:> page 170
Cruise control system*
Parking aid*
Aud io*
Telephone* Navigation*
Driver in forma tion system
© Odometer and trip odometer (only in the
first tab*)
<::>p age 10
@ Outside temperature ¢ page 9, selector
l ever posit ion
(D Tips
- Yo u can set the units used for temperature,
speed and other measurements in the Info ­
tainment system.
- For information on the audio and naviga­
tion* functions, refer to the separate Info­
tainment system owner's manual.
Operation
Operating using the windshield wiper lever
Appl ies to: vehicles with driver information system without
multifu nction steer ing wheel
-------- ®
Fig. 7 Windshield wiper lever: operating the driver infor ­
ma tion system
Operating
• Switch the ignition on . The last select function
is displayed.
• To switch betwee n the on-board computer
0,
fJ , the efficiency program ii or, for example,
the cruise contro l system*, press the
I RESET I
button @.
• To access additiona l information below or
above, press the button @ down or up .
Recalling indicator lights and messages
• Press the !RESET I button @.
Resetting values to zero
• Select a value in the desired trip computer or in
the efficiency program. ..,.
19

Driver information system
• Press and hold the I RESET I button @for at
least one second . All values in the selected on­
board computer or in the efficiency program
are reset to zero.
Operating using the multifunction steering
wheel
A pp lies to: ve hicles w ith driver information system and multi­
fun ction s teeri ng w hee l
Fig. 8 Mult ifunction steering wheel: operat ing the drive r
i nfo rmation system
The tab@¢ page 19, fig. 6 appears once you
press a button on the mult ifunction steering
wheel.
Operating
,-.. ~ N
0
Cl • Switch the ignition on. The last select function
is d isp layed.
• To switch between the tabs, press the button
(D to the left or right~ fig. 8.
• To access additional information below or
above, turn the thumbwheel @down or up.
• To confirm a selection, press the t humbwheel
@ .
Opening Car functions
• Se lect the first tab with the button (D .
• Press the button @. Th e Car functions menu is
displayed .
• To se lect a menu item, turn and press the
thu mbwheel @.
• To se lect a function programmed to a steering
wheel button, press the button
@ .
Resetting values to zero
• In the Car functions me nu, select On-board
computer or Efficiency program.
20 •
Select a value in the desired trip computer or in
the efficiency program.
• To reset the va lues in a memory, press and hold
the thumbwheel @for one second.
Assigning a function to a programmable
steering wheel button
• Select the ICAR I button> (Car) Systems* con­
trol button >
Vehicle settings > Steering wheel
button .
Recalling indicator lights and messages
• Select the D tab.
The
D tab is on ly visible when there is at least
one indicator light or message displayed. Ot her
folders are only v is ib le if the applicable system is
switched on .
On-board computer
Applies to: vehicles wi th on -boa rd comp uter
Fig. 9 Display: on -boa rd computer memory level 1
Operating with the windshield wiper lever*
• Press the I RESET I button @ ¢ page 19, fig. 7
repeatedly until the on-board computer ap­
pears in the disp lay.
• To access add itiona l content, press the button
®·
Operating with the multifunction steering
wheel*
• Open Car functions and select the On-board
computer
menu item ~ page 20.
• To access additiona l content, turn the thu mb-
wheel @~
page 20, fig. 8. ""

Opening and closing
Central locking
Description
You can lock and unlock the veh icle centrally . You
have the following options:
- Remote control key
c> page 25,
-Sensors in the door handles* c> page 26,
-Inner central locking switch c> page 2 7, or
- Lock cylinder on the driver's door
c> page 28.
Turn signals
The turn s ignals flash tw ice when you un lock the
veh icle and flash once when you lock the vehicle.
If the vehicle is unlocked and the flashing contin­
ues, then
- one of the doors or the luggage compa rtment
lid is open,
- the ignition is still switched on, or
- the P selector lever position (vehicles with au -
tomat ic transmission*) is not engaged.
Auto Lock
The Auto Lock function locks all doors and the
luggage compartment lid once the speed has ex­
ceeded approximately 9 mph (15 km/h) .
T he vehicle can be unlocked if the opening func­
tion in the central locking system switch is used,
one of the door handles is pulled or the ignition key is removed.
In the event of a crash with airbag deployment,
the doors will also automatically unlock to allow
access to the vehicle.
Selective door unlocking
The doors and luggage compartment lid will lock
when they close. You can set in the Infotainment
system if
only the driver's door or the entire vehi ­
cle shou ld unlock when unlocking
c> page 27 ,
Setting the central locking system.
Unintentionally locking yourself out
~ The following conditions prevent you from lock-.....,
~ ing your remote control key in the vehicle: N ...... 0 0
:::,
00
Opening and closing
- If the driver's door is open, the vehicle cannot
be locked by pressing the
fi'.J button on the re­
mote contro l key or touching the locking sen­
sor* on a door.
- When locking using the
ffi button in the central
locking switch, the vehicle will not lock if a door
is open
c> page 27.
- If the most recently used convenience key* is in
the luggage compartment, the luggage com­
partment lid automatically unlocks again after
closing it
c> page 28. The emergency flashers
blink four times.
Do not lock your vehicle with the remote control
key or convenience key* until all doors and the
luggage compartment lid are closed . This helps
to prevent you from locking yourself out acc iden­
tally .
A WARNING
- When you leave the vehicle, always remove
the ignition key and take it with you. This
will prevent passengers (children, for exam­
ple) from accidenta lly being locked in the
vehicle should they accidentally press the
power locking switch in the front doors.
- Do not leave children inside the vehicle un­
supervised. In an emergency it would be im­
possible to open the doors from the outside
without the key.
(D Tips
- Do not leave valuables unattended in the ve­
hicle. A locked vehicle is not a safe!
- The LED in the driver's door rail blinks when
you lock the vehicle . If the LED lights up for
approximately 30 seconds after locking,
there is a malfunction in the central locking
system . Have the problem corrected by an
authorized Audi dealer or authorized Audi
Service Facility.
23