2016 NISSAN NOTE lock

TM-5
CEF
G H
I
J
K L
M A
B
TM
N
O P
P0999 SHIFT SOLENOID F .............................195
DTC Logic ........................................................... ..195
Diagnosis Procedure .............................................195
Component Inspection (Low Brake Solenoid
Valve) ....................................................................
195
P099B SHIFT SOLENOID G ............................197
DTC Logic ........................................................... ..197
Diagnosis Procedure .............................................197
Component Inspection (High Clutch & Reverse
Brake Solenoid Valve) ...........................................
197
P099C SHIFT SOLENOID G ............................199
DTC Logic ........................................................... ..199
Diagnosis Procedure .............................................199
Component Inspection (High Clutch & Reverse
Brake Solenoid Valve) ...........................................
199
P1586 G SENSOR ............................................201
DTC Logic .............................................................201
Diagnosis Procedure .............................................201
P1588 G SENSOR ............................................204
DTC Logic .............................................................204
Diagnosis Procedure .............................................204
P2765 CLUTCH B SPEED SENSOR ...............206
DTC Logic ........................................................... ..206
Diagnosis Procedure .............................................206
P2857 CLUTCH A PRESSURE .......................209
DTC Logic ........................................................... ..209
Diagnosis Procedure .............................................209
P2858 CLUTCH B PRESSURE .......................210
DTC Logic ........................................................... ..210
Diagnosis Procedure .............................................210
P2859 CLUTCH A PRESSURE .......................211
DTC Logic ........................................................... ..211
Diagnosis Procedure .............................................212
P285A CLUTCH B PRESSURE .......................213
DTC Logic ........................................................... ..213
Diagnosis Procedure .............................................214
MAIN POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................
215
Diagnosis Procedure ........................................... ..215
OVERDRIVE CONTROL SWITCH ...................217
Component Function Check ................................ ..217
Diagnosis Procedure .............................................217
Component Inspection (Overdrive Control Switch)
..
218
OD OFF INDICATOR LAMP ............................219
Component Function Check ..................................219
Diagnosis Procedure .............................................219
SHIFT POSITION INDICATOR CIRCUIT .........220
Component Parts Function Inspection ................ ..220
Diagnosis Procedure ........................................... ..220
SHIFT LOCK SYSTEM ...................................221
Component Function Check ..................................221
Diagnosis Procedure .............................................221
SYMPTOM DIAGNOSIS ............................223
CVT CONTROL SYSTEM ...............................223
Symptom Table ................................................... ..223
PERIODIC MAINTENANCE ......................228
CVT FLUID ......................................................228
Inspection ............................................................ ..228
Replacement .........................................................228
Adjustment .............................................................229
REMOVAL AND INSTALLATION .............231
CVT SHIFT SELECTOR ..................................231
Exploded View ..................................................... ..231
Removal and Installation .......................................231
Disassembly and Assembly ...................................232
Inspection ..............................................................232
CONTROL CABLE ..........................................234
Exploded View .......................................................234
Removal and Installation .......................................234
Inspection and Adjustment ....................................236
KEY INTERLOCK CABLE ..............................237
Exploded View .......................................................237
Removal and Installation .......................................237
Inspection ..............................................................238
TCM .................................................................239
Exploded View .......................................................239
Removal and Installation .......................................239
Adjustment .............................................................239
AIR BREATHER HOSE ..................................240
Removal and Installation .......................................240
G SENSOR ......................................................241
Exploded View .......................................................241
Removal and Installation .......................................241
Adjustment .............................................................241
OIL PAN, CONTROL VALVE .........................242
Exploded View .......................................................242
Removal and Installation .......................................242
Inspection and Adjustment ....................................245
PRIMARY SPEED SENSOR ...........................246
Exploded View .......................................................246
Removal and Installation .......................................246
Inspection and Adjustment ....................................246
SECONDARY SPEED SENSOR ....................247
Exploded View .......................................................247
Removal and Installation .......................................247
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-20
< REMOVAL AND INSTALLATION >[5MT: RS5F91R]
CONTROL LINKAGE
CONTROL LINKAGE
Exploded ViewINFOID:0000000012430954
Removal and InstallationINFOID:0000000012430955
REMOVAL
1. Move the shift selector to the neutral position.
2. Remove the battery tray. Refer to
PG-71, "
Removal and Installation (Battery Tray)".
3. Pull out and disconnect cables from shifter lever A and selector lever, using a suitable tool.
4. While pressing the lock of the selector cable in the direction of the arrows shown, remove the selector cable from the cable
mounting bracket.
5. While pressing the lock of the shifter cable in the direction of the arrows shown, remove the shifter cable from the cable mounting
bracket.
6. Remove cable mounting bracket from clutch housing.
7. Pull the shift selector handle upward to remove.
8. Remove center console assembly. Refer to IP-18, "
Removal and
Installation".
9. Pull out and disconnect each cable from the shift selector assembly, using a suitable tool.
1. Shifter lever A 2. Selector lever 3. Selector cable
4. Shifter cable 5. Cable mounting bracket6. Tapping bolt
7. Bracket 8. Grommet9. Shift selector assembly
10. Shift selector 11. Shift selector handle
JPDIC0789GB
JPDIC0793ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

CONTROL LINKAGETM-21
< REMOVAL AND INSTALLATION > [5MT: RS5F91R]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
a. While pressing the lock of the selector cable in the direction of the arrows shown, remove the selector cable from the shift
selector assembly.
b. While pressing the lock of the shifter cable in the direction of the arrows shown, remove the shifter cable from the shift selector
assembly.
10. Remove the shift selector assembly.
11. Remove center muffler, exhaust front tube, and heat plate. Refer to EX-5, "
Exploded View".
12. Remove the bracket from the vehicle.
13. Remove the grommet and then remove the shifter cable and selector cable from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Install each cable without causing in terference with other parts. Do not allow cable to bend less than
120 mm (4.72 in), or exceed 180 degree twist.
• Install boot of each cable without causing interference with other parts. Do not exceed 90 degree twist.
• Fit boot to center console assembly an d the groove on shift selector handle.
• To install the shift selector handle, press it onto the shift selector. CAUTION:
• Do not reuse shift selector handle.
• Be careful with orientation of shift selector handle.
• Bolt hole is not threaded on new clutch housing. Self-tapping bolt is used to attach lock plate to clutch hous-
ing.
CAUTION:
Do not reuse self-tapping bolt.
• Insert each cable until it reaches the cable mounting bracket and shift selector assembly.
• Insert each cable until it reaches the shifter lever A and the selector lever.
• Move the shift selector to the neutral position.
InspectionINFOID:0000000012430956
INSPECTION AFTER INSTALLATION
Shift Selector Handle
Check that the shift selector handle is installed in the right position.
Shifter Cable and Selector Cable
• Pull each cable in the removal direction to check that it does not disconnect from the cable mounting
bracket.
• Pull each cable in the removal direction to check that it does not disconnect from the shift selector assembly.
• Pull grommet in the removal direction to che ck that it does not disconnect from the vehicle.
Shift Selector Assembly and Shift Selector
• Check that there is no unusual noise, binding, bending, looseness, and interference when the shift selector
is moved to each position. If there is a malfuncti on, then repair or replace the malfunctioning part.
• Check that the shift selector smoothl y returns to the neutral position after moving the shift selector from 1st
to 2nd gear and releasing it. If there is a malfunction, then repair or replace the malfunctioning part.
• Check that the shift selector smoothly returns to the neutral position after moving the shift selector from 5th to the reverse gear position and releasing it. If there is a malfunction, then repair or replace the malfunction-
ing part.
JPDIC0793ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-24
< UNIT REMOVAL AND INSTALLATION >[5MT: RS5F91R]
TRANSAXLE ASSEMBLY
UNIT REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded ViewINFOID:0000000012430961
Removal and InstallationINFOID:0000000012430962
WARNING:
Do not remove the radiator cap when the engine is
hot. Serious burns could occur from high pressure
coolant escaping from the radiator. Wrap a thick clot h around the cap. Slowly turn it a quarter turn to
allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
Do not reuse CSC (Concentric Slave Cylinder). The CSC slides back to the orig inal position every time
the transaxle assembly is removed. This action may allow dust or contaminants to gather on the slid-
ing parts and damage a seal of CSC causing clutch fluid leakage.
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the engine and transaxle assembly. Refer to EM-87, "Removal and Installation".
2. Disconnect the reverse lamp switch harness connector.
3. Remove the bolts that fasten the transaxle assembly and engine assembly.
4. Remove transaxle assembly from the engine assembly.
5. Remove engine mounting bracket (LH). Refer to EM-86, "
Exploded View".
6. Remove CSC (Concentric Slave Cylinder). Refer to CL-17, "
Removal and Installation".
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Secure transaxle assembly to a suitable jack.
• The transaxle assembly must not interfere with the wire harnesses and clutch tube.
• When installing transaxle assembly, do not bring input shaft into contact with clutch cover.
• Bolt hole is not threaded on new clutch housing. Self-tapping bolt is used to attach lock plate to
clutch housing.
1. Transaxle assembly
: Refer to "INSTALLATION" in TM-24, "
Removal and Installation" for the locations and tightening torque.
JPDIC0478ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

TRANSAXLE ASSEMBLYTM-27
< UNIT DISASSEMBLY AND ASSEMBLY > [5MT: RS5F91R]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
MAINSHAFT AND GEAR
1. Input shaft front bearing 2. Input shaft 3. Snap ring
4. Input shaft rear bearing 5. Adapter plate 6. Bushing
7. 5th input gear 8. 5th-reverse baulk ring 9. Synchronizer lever
10. 5th-reverse synchronizer hub 11. 5th-reverse coupling sleeve 12. Lock washer
13. Retaining pin 14. Reverse gear
: Apply gear oil.
: Replace the parts as a set.
JPDIC0820GB
Revision: August 2015 2016 Versa Note

cardiagn.com

TRANSAXLE ASSEMBLYTM-29
< UNIT DISASSEMBLY AND ASSEMBLY > [5MT: RS5F91R]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
FINAL DRIVE
1. Retaining pin 2. 1st-2nd shift fork3. Bushing
4. 1st-2nd fork rod 5. Lock pin 6. 5th-reverse fork rod
7. 5th-reverse shift fork 8. Check ball 9. 3rd-4th shift fork
10. 3rd-4th fork rod 11.Control shaft 12. O-ring
13. Selector 14. Check ball plug 15. Bushing
16. Spring 17. Gear catch
: Apply gear oil.
: Apply Genuine Silicone RTV or equivalent. Refer to GI-22, "
Recommended Chemical Products and Sealants".
: Replace the parts as a set.
AWBIA1480ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-30
< UNIT DISASSEMBLY AND ASSEMBLY >[5MT: RS5F91R]
TRANSAXLE ASSEMBLY
Disassembly
INFOID:0000000012430965
1. Remove drain plug and gasket from clutch housing using suitable tool, and drain gear oil.
2. Remove filler plug and gasket from transaxle case.
3. Remove rear housing and O-ring. CAUTION:
Remove in direction of input shaft ( ) as shown. Rear
housing oil channel is inserte d to input shaft center hole.
4. Move the shifter lever A (1) to the 3rd gear position. NOTE:
• If it is not moved to the 3rd gear position, transaxle case can-
not be removed from clutch housing.
• The 3rd gear position means that shifter lever A is fully rotated
clockwise and it is returned approximately 10 degrees.
1. Differential side bearing outer race 2. Differential side bearing 3. Final drive
: Replace the parts as a set.
JPDIC0481ZZ
SCIA1709J
PCIB1524E
Revision: August 2015 2016 Versa Note

cardiagn.com

TRANSAXLE ASSEMBLYTM-31
< UNIT DISASSEMBLY AND ASSEMBLY > [5MT: RS5F91R]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
5. Remove 5th-reverse shift fork (1) and 5th-reverse coupling sleeve.
a. Remove retaining pin from 5th-reverse shift fork, using a suit- able tool (A).
b. Press 5th-reverse shift fork, shift to 5th, and then engage it with 3rd gear.
c. Remove bolt (B).
d. Remove nut (C) and lock washer. CAUTION:
• Do not reuse nut.
• Do not use an impact wrench for removal. Gears may bedamaged.
e. Remove 5th-reverse shift fork and 5th-reverse coupling sleeve from 5th-reverse synchronizer hub.
6. Remove 5th-reverse synchronizer hub from input shaft, using a suitable tool.
CAUTION:
Set claw of suitable tool to the wider side of the hub when
setting the suitable tool in 5th-reverse synchronizer hub.
7. Remove synchronizer levers, 5th-reverse baulk ring, 5th input
gear, bushing, and adapter plate from input shaft.
8. Remove 5th main gear from mainshaft, using Tools.
9. Remove position switch from transaxle case.
JPDIC0532ZZ
PCIB1526E
Tool number (A): KV32300QAC ( — ) (B): KV32300QAD ( — )
PCIB1527E
PCIB1627E
Revision: August 2015 2016 Versa Note

cardiagn.com