2016 NISSAN NOTE turn signal

TM-98
< SYSTEM DESCRIPTION >[CVT: RE0F11A]
DIAGNOSIS SYSTEM (TCM)
WORK SUPPORT
*: “Clutch point learning” can
be selected, but do not use it.
Engine brake adjustment
Check the degradation level of the CVT fluid.
G SEN SLOPE (%) Displays the gradient angle calculated from the G sensor
signal voltage.
ENGBRKLVL (On/Off) Displays the setting of “ENGINE BRAKE ADJ” in “Work
Support”.
PVIGN VOLT (V) ×Displays the backup voltage of TCM.
TRGT AUX GR RATIO Displays the target gear ratio of the auxiliary gearbox cal-
culated from processing of gear shift control.
G SEN CALIBRATION (YET/DONE) Displays the status of “G
SENSOR CALIBRATION” in
“Work Support”.
N IDLE STATUS (On/Off) Displays idle neutral status.
CVT-B • Displays CVT fluid temperature count.
• This monitor item does not use.
CVT-A • Displays CVT fluid temperature count.
• This monitor item does not use.
Monitored item
(Unit)Monitor item selection
Remarks
MAIN SIG-
NALS ECU IN-
PUT SIG-
NALS
Item name Description
ENGINE BRAKE ADJ. Although there is no malfunction on the transaxle and the CVT system, if a customer
make a complaint like “I do not feel comfortable with automatic operation of the engine
brake on downhill”, the engine brake may be cancelled with “engine brake adjust-
ment”.
CONFORM CVTF DETERIORTN Check the degradation level of the CVT fluid under severe conditions.
G SENSOR CALIBRATION Compensate the G sensor.
ERASE CALIBRATION DATA Erase the calibration data memorized by TCM.
ERASE LEARNING VALUE Erase the learning value me morized by TCM.
ERASE MEMORY DATA Perform “erasing of the calibration data” and “erasing of the learned value” at the same
time.
CLUTCH POINT LEARNING* Allow learning of the clutch engagement point of the auxiliary gearbox for TCM.
ENGINE BRAKE LEVEL
ON : Turn ON the engine brake control.
OFF : Turn OFF the engine brake control.
CVTF degradation level data
210,000 or more : Replacement of the CVT fluid is required.
Less than 210,000 : Replacement of the CVT fluid is not required.
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-136
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
U0100 LOST COMMUNICATION (ECM A)
U0100 LOST COMMUNICATION (ECM A)
DescriptionINFOID:0000000012431056
CAN (Controller Area Network) is a serial communication
line for real-time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehi cle, and each control unit shares information and links
with other control units during operation (not independently). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H line, CAN-L li ne) allowing a high rate of information transmission
with less wiring. Each control unit transmits/recei ves data but selectively reads required data only.
DTC LogicINFOID:0000000012431057
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and wait for at least 5 seconds.
2. Check the DTC.
Is
“U0100” detected?
YES >> Go to TM-136, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431058
For the diagnosis procedure, refer to LAN-16, "Trouble Diagnosis Flow Chart".
DTC Trouble diagnosis name DTC detection conditionPossible causes
U0100 Lost Communication With
ECM/PCM A When the ignition switch is ON, TCM is un-
able to receive the CAN communications
signal from ECM continuously for 2 sec-
onds or more. •ECM
• Harness or connector
(CAN communication line is open or
shorted)
Revision: August 2015 2016 Versa Note

cardiagn.com

U0140 LOST COMMUNICATION (BCM)TM-137
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
U0140 LOST COMMUNICATION (BCM)
DescriptionINFOID:0000000012431059
CAN (Controller Area Network) is a serial communication line for real-time application. It is an on-vehicle mul-
tiplex communication line with high data communica tion speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicle, and each control unit shares information and links
with other control units during operation (not independently ). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H line, CAN-L li ne) allowing a high rate of information transmission
with less wiring. Each control unit transmits/receives data but selectively reads required data only.
DTC LogicINFOID:0000000012431060
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Start the engine and wait for at least 5 seconds.
2. Check the DTC.
Is
“U0140” detected?
YES >> Go to TM-137, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431061
For the diagnosis procedure, refer to LAN-16, "Trouble Diagnosis Flow Chart".
DTC Trouble diagnosis name DTC detection conditionPossible causes
U0140 Lost Communication With
Body Control Module When the ignition switch is ON, TCM is unable
to receive the CAN communications signal
from BCM continuously for 2 seconds or more. •BCM
• Harness or connector
(CAN communication line is open or
shorted)
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-138
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
U0141 LOST COMMUNICATION (BCM A)
U0141 LOST COMMUNICATION (BCM A)
DescriptionINFOID:0000000012431062
CAN (Controller Area Network) is a serial communication
line for real-time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehi cle, and each control unit shares information and links
with other control units during operation (not independently). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H line, CAN-L li ne) allowing a high rate of information transmission
with less wiring. Each control unit transmits/recei ves data but selectively reads required data only.
DTC LogicINFOID:0000000012431063
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Start the engine and wait for at least 5 seconds.
2. Check the DTC.
Is
“U0141” detected?
YES >> Go to TM-138, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431064
For the diagnosis procedure, refer to LAN-16, "Trouble Diagnosis Flow Chart".
DTC Trouble diagnosis name DTC detection conditionPossible causes
U0141 Lost Communication With
Body Control Module A When the ignition switch is turned ON, TCM
continues no reception of the CAN communi-
cation signal from IPDM E/R for 2 seconds or
more. • IPDM E/R
• Harness or connector
(CAN communication line is open or
shorted)
Revision: August 2015 2016 Versa Note

cardiagn.com

U0155 LOST COMMUNICATION (IPC)TM-139
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
U0155 LOST COMMUNICATION (IPC)
DescriptionINFOID:0000000012431065
CAN (Controller Area Network) is a serial communication line for real-time application. It is an on-vehicle mul-
tiplex communication line with high data communica tion speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicle, and each control unit shares information and links
with other control units during operation (not independently ). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H line, CAN-L li ne) allowing a high rate of information transmission
with less wiring. Each control unit transmits/receives data but selectively reads required data only.
DTC LogicINFOID:0000000012431066
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Start the engine and wait for at least 5 seconds.
2. Check the DTC.
Is
“U0155” detected?
YES >> Go to TM-139, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431067
For the diagnosis procedure, refer to LAN-16, "Trouble Diagnosis Flow Chart".
DTC Trouble diagnosis name DTC detection conditionPossible causes
U0155 Lost Communication With In-
strument Panel Cluster (IPC)
Control Module When the ignition switch is ON, TCM is unable
to receive the CAN communications signal
from the combination meter continuously for 2
seconds or more. • Combination meter
• Harness or connector
(CAN communication line is open or
shorted)
Revision: August 2015 2016 Versa Note

cardiagn.com

U1000 CAN COMM CIRCUITTM-141
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000012431071
CAN (Controller Area Network) is a serial communication line for real-time application. It is an on-vehicle mul-
tiplex communication line with high data communica tion speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicle, and each control unit shares information and links
with other control units during operation (not independently ). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H line, CAN-L li ne) allowing a high rate of information transmission
with less wiring. Each control unit transmits/receives data but selectively reads required data only.
DTC LogicINFOID:0000000012431072
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Start the engine and wait for at least 5 seconds.
2. Check the DTC.
Is
“U1000” detected?
YES >> Go to TM-141, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431073
For the diagnosis procedure, refer to LAN-16, "Trouble Diagnosis Flow Chart".
DTC Trouble diagnosis name DTC detection conditionPossible causes
U1000 CAN Communication Line When the ignition switch is ON, TCM cannot
send the CAN communication signal continu-
ously for 2 seconds or more. Harness or connector
(CAN communication line is open or
shorted)
Revision: August 2015
2016 Versa Note

cardiagn.com

TM-142
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
U1117 LOST COMMUNICATION (ABS)
U1117 LOST COMMUNICATION (ABS)
DescriptionINFOID:0000000012431074
CAN (Controller Area Network) is a serial communication
line for real-time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehi cle, and each control unit shares information and links
with other control units during operation (not independently). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H line, CAN-L li ne) allowing a high rate of information transmission
with less wiring. Each control unit transmits/recei ves data but selectively reads required data only.
DTC LogicINFOID:0000000012431075
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Start the engine and wait for 5 seconds or more.
2. Check the DTC.
Is
“U1117” detected?
YES >> Go to TM-142, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431076
For the diagnosis procedure, refer to LAN-16, "Trouble Diagnosis Flow Chart".
DTC Trouble diagnosis name DTC detection conditionPossible causes
U 111 7 Lost Communication With
ABS When the ignition switch is ON, TCM is unable
to receive the CAN communications signal
from ABS actuator and electric unit (control
unit) continuously for 2 seconds or more. • ABS actuator and electric unit (control
unit)
• Harness or connector (CAN communication line is open or
shorted)
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-144
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
P0705 TRANSMISSION RANGE SENSOR A
P0705 TRANSMISSION RANGE SENSOR A
DTC LogicINFOID:0000000012431080
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
1. Start the engine.
2. Maintain the following conditions.
3. Shift the selector lever through entire positions from “P ” to “L”. (Hold the selector lever at each position for
10 seconds or more.)
4. Check the first trip DTC.
Is
“P0705” detected?
YES >> Go to TM-144, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431081
1.CHECK TCM INPUT SIGNALS
With CONSULT
1. Turn ignition switch ON.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, “P POSITION SW” and “L POSITION
SW”.
4. Shift the selector lever through entire positions fr om “P” to “L” and check ON/OFF of each monitor item.
DTC Trouble diagnosis name DTC detection conditionPossible causes
P0705 Transmission Range Sensor
A Circuit (PRNDL Input) Two or more range signals simultaneously
stay ON continuously for 5 seconds under the
following diagnosis condition 1 and 2:
• Diagnosis condition 1 (continued for 5 sec-
onds or more)
- TCM power supply voltage: More than 11 V
• Diagnosis condition 2 (continued for 2 sec- onds or more)
- Vehicle speed: Less than 3 km/h (2 MPH)
- Accelerator pedal position: 0.6/8 or less
- Idle switch: ON
- Stop lamp switch: ON • Harness or connector
(Short circuit between transmission
range switch and TCM)
• Transmission range switch
Accelerator pedal position : 0.0/8
Brake pedal : Depressed
Vehicle speed : 0 km/h (0 MPH)
Monitor item Test condition Condition
D POSITION SW Selector lever: “D” position On
Other than the above
Off
Revision: August 2015 2016 Versa Note

cardiagn.com