2016 NISSAN NOTE trans

SECONDARY SPEED SENSORTM-247
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SECONDARY SPEED SENSOR
Exploded ViewINFOID:0000000012431198
Removal and InstallationINFOID:0000000012431199
REMOVAL
1. Remove battery tray. Refer to PG-71, "Removal and Installation (Battery Tray)".
2. Remove IPDM/ER. Refer to PCS-30, "
Removal and Installation".
3. Disconnect the harness connector from secondary speed sensor.
4. Remove the secondary speed sensor.
5. Remove the O-ring from the secondary speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-ring.
Inspection and AdjustmentINFOID:0000000012431200
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to TM-228, "Inspection".
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to TM-229, "Adjustment".
1. Transaxle assembly 2. O-ring3. Secondary speed sensor
Front : Genuine NISSAN CVT Fluid NS-3
JSDIA1881GB
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-248
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
OUTPUT SPEED SENSOR
OUTPUT SPEED SENSOR
Exploded ViewINFOID:0000000012431201
Removal and InstallationINFOID:0000000012431202
REMOVAL
1. Disconnect the harness connector from output speed sensor.
NOTE:
Lift up the vehicle and perform the work from rear of the transaxle assembly.
2. Remove the output speed sensor.
3. Remove the O-ring from the output speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-ring.
Inspection and AdjustmentINFOID:0000000012431203
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to TM-228, "Inspection".
ADJUSTMENT AFTER INSTALLATION
Check the CVT fluid level. Refer to TM-229, "Adjustment".
1. Transaxle assembly 2. Output speed sensor 3. O-ring
Front Genuine NISSAN CVT Fluid NS-3
JSDIA1882GB
Revision: August 2015 2016 Versa Note

cardiagn.com

DIFFERENTIAL SIDE OIL SEALTM-249
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
DIFFERENTIAL SIDE OIL SEAL
Exploded ViewINFOID:0000000012431204
Removal and InstallationINFOID:0000000012431205
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the front drive shaft from the transaxle assembly. Refer to FAX-19, "Removal and Installation"
2. Remove the differential side oil seal using suitable tool.
CAUTION:
When removing the differential side oil seal, be careful not to scratch the oil seal mating surfaces
of the transaxle case and converter housing.
INSTALLATION
CAUTION:
When inserting the drive shaf t, be sure to use Tool.
1. Measure height (A) of seal lip. Calculate protrusion (C) of seal
lip according to measured height (A) of seal lip and reference
value (B) of side oil seal insertion.
CAUTION:
• Do not reuse differential side oil seal.
• Put a mark on the measurement area and measure height of seal lip at four points diagonally
using suitable tool.
NOTICE:
1. Transaxle assembly 2. Differential side oil seal (left side) 3. Differential side oil seal (right side)
Front Genuine NISSAN CVT Fluid NS-3
JSDIA1888ZZ
Tool number : KV38107900 ( — )
(1) : Differential side oil seal
(2) : Converter housing or transaxle case
Lip protrusion (C): C=A–B
Differential side oil seal insertion
reference value (B) : 1.8 mm (0.071 in)
JSDIA4816ZZ
Revision: August 2015
2016 Versa Note

cardiagn.com

TM-252
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
WATER HOSE
6. Remove the bracket.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse hose clamps.
• Do not reuse clips.
• When installing bracket A to the transaxle assembly.
- Face arrow (A) of bracket A toward the front of the vehicle.
- Set baffle (B) of bracket
A to rib (C) of transaxle.
• When installing the bracket B to the transaxle assembly.
- Face arrow (A) of bracket A towards the top of vehicle.
- Insert baffle (B) into the boss hole (C) of transaxle.
• Refer to the following when installing water hoses.
• Refer to the following when installing hose clamp. CAUTION:
Hose clamp should not interfere with the bulge of fluid cooler tube.
: Front
JSDIA4112ZZ
: Front
JSDIA4113ZZ
Water hose (1)Installation side
tube (2) Direction of paint
mark Hose insertion depth
(L)
Water hose A Water outlet Upward
(A): 27 mm (1.06 in)
(End reaches the 2-
stage bulge.)
CVT oil warmer Frontward
Water hose B CVT oil warmer Frontward
Water bypass pipe
Rightward (Align
with the mark of
the water by-
pass pipe side)
Water hose C Water bypass pipe —
Water outlet Upward
JSDIA2459ZZ
Revision: August 2015
2016 Versa Note

cardiagn.com

TM-256
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
CVT OIL WARMER
CVT OIL WARMER
Exploded ViewINFOID:0000000012431217
Removal and InstallationINFOID:0000000012431218
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns coul
d occur from high pressure
engine coolant escaping from the radiator. Wrap a thick cloth ar ound the cap. Slowly turn it a quarter
turn to allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
Perform these steps after the coolant temperature has cooled sufficiently.
1. Pull out water hose from CVT oil warmer. Refer to TM-251, "
Removal and Installation".
2. Pull out fluid cooler hose from CVT oil warmer. Refer to TM-254, "
Removal and Installation".
3. Remove CVT oil warmer.
4. Remove O-ring from CVT oil warmer.
INSTALLATION
Note the followings and install in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
InspectionINFOID:0000000012431219
INSPECTION AFTER INSTALLATION
Start the engine and check visually that ther e is no leakage of CVT fluid and engine coolant.
ADJUSTMENT AFTER INSTALLATION
Adjust CVT fluid level. Refer to TM-229, "Adjustment".
1. Transaxle assembly 2. CVT oil warmer 3. O-ring
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA5447GB
Revision: August 2015 2016 Versa Note

cardiagn.com

CVT FLUID FILTERTM-257
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
CVT FLUID FILTER
Exploded ViewINFOID:0000000012431220
Removal and InstallationINFOID:0000000012431221
REMOVAL
1. Remove fender protector (LH). Refer to EXT-38, "Removal and Installation".
2. Remove fluid filter cover bolt (A).
1. Transaxle assembly 2. CVT fluid filter3. Fluid filter cover
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA5448GB
JSDIA5047ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-258
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
CVT FLUID FILTER
3. Turn fluid filter cover (1) counterclockwise and remove it from
transaxle.
CAUTION:
Do not reuse fluid filter cover.
4. Remove CVT fluid filter (1) from transaxle. CAUTION:
Do not reuse CVT fluid filter.
INSTALLATION
Note the following and install in the reverse order of removal.
NOTE:
Inspect the CVT fluid level. Refer to TM-228, "
Inspection".
CAUTION:
• Never reuse CVT fluid filter and fluid filter cover.
• Apply CVT fluid to O-ring of fluid filter cover.
InspectionINFOID:0000000012431222
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Adjust CVT fluid level. Refer to TM-229, "Adjustment".
JSDIA5048ZZ
JSDIA5049ZZ
JSDIA5450ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

TRANSMISSION ASSEMBLYTM-259
< UNIT REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
UNIT REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
Exploded ViewINFOID:0000000012431223
Removal and InstallationINFOID:0000000012431224
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high-pressure
engine coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly push down and
turn it a quarter turn to allow built-up pressure to escape. Carefully remove the cap by pushing it down
and turning it all the way.
CAUTION:
• Perform these steps after the coolant temperature has cooled sufficiently.
• When replacing the transaxle, perform "ADDI TIONAL SERVICE WHEN REPLACING TRANSAXLE
ASSEMBLY". Refer to TM-127, "
Description".
NOTE:
When removing components such as hoses, tubes/line, etc. , cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the engine and transaxle assembly. Refer to EM-87, "Removal and Installation".
2. Disconnect the harness connectors and harnesses. • For CVT unit harness connector.
• Transmission position switch harness connector
1. Transaxle assembly
A : For the tightening torque, refer to TM-259, "
Removal and Installation".
JSDIA1890ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com