2016 NISSAN NOTE Display

MWI-94
< DTC/CIRCUIT DIAGNOSIS >[TYPE B]
U1010 CONTROL UNIT (CAN)
U1010 CONTROL UNIT (CAN)
DescriptionINFOID:0000000012432621
Initial diagnosis of combination meter.
DTC LogicINFOID:0000000012432622
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000012432623
1.REPLACE COMBINATION METER
When DTC U1010 is detected, replace combination meter. Refer to MWI-115, "
Removal and Installation".
>> Inspection End.
DTC Display Item Malfunction detected condition Possible malfunction
U1010 CONTROL UNIT (CAN)
[U1010] When detecting error during the initial diagnosis of
the CAN controller of combination meter.
Combination meter
Revision: August 2015
2016 Versa Note

cardiagn.com

MWI
B2205 VEHICLE SPEEDMWI-95
< DTC/CIRCUIT DIAGNOSIS > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
B2205 VEHICLE SPEED
DescriptionINFOID:0000000012432624
The ABS actuator and electric unit (control unit) provi des a vehicle speed signal to the combination meter via
CAN communication lines.
DTC LogicINFOID:0000000012432625
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000012432626
1.CHECK COMBINATION METER INPUT SIGNAL
1. Start engine and select METER/M&A on CONSULT.
2. Using SPEED METER on DATA MONITOR, compar e the value of DATA MONITOR with speedometer
pointer of combination meter. Speedometer and DATA MONITOR indications should be close.
Is the inspection result normal?
YES >> Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to BRC-31, "CONSULT
Function (ABS)".
NO >> Replace combination meter. Refer to MWI-115, "
Removal and Installation".
DTC Display Item Malfunction detected condition Possible malfunction
B2205 VEHICLE SPEED CIRC
[B2205] Malfunction is detected when an erroneous
speed signal is received for 2 seconds or
more. • Combination meter
• ABS actuator and electric unit (control unit)
Revision: August 2015
2016 Versa Note

cardiagn.com

MWI-96
< DTC/CIRCUIT DIAGNOSIS >[TYPE B]
B2267 ENGINE SPEED
B2267 ENGINE SPEED
DescriptionINFOID:0000000012432627
The engine speed signal is transmitted from ECM to
the combination meter via CAN communication.
DTC LogicINFOID:0000000012432628
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000012432629
1.PERFORM SELF-DIAGNOSIS OF ECM
Perform Self Diagnostic Result of ECM, and repair or replace malfunctioning parts.
>> Refer to EC-60, "
CONSULT Function".
DTC Display Item Malfunction detected condition Possible malfunction
B2267 TACHO METER
[B2267] ECM continuously transmits abnormal engine
speed signals for 2 seconds or more • Crankshaft position sensor (POS)
•ECM
Revision: August 2015
2016 Versa Note

cardiagn.com

MWI
B2268 WATER TEMPMWI-97
< DTC/CIRCUIT DIAGNOSIS > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
B2268 WATER TEMP
DescriptionINFOID:0000000012432630
The engine coolant temperature signal is transmitted fr om ECM to the combination meter via CAN communi-
cation.
DTC LogicINFOID:0000000012432631
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000012432632
1.PERFORM SELF-DIAGNOSIS OF ECM
Perform Self Diagnostic Result of ECM, and repair or replace malfunctioning parts.
>> Refer to EC-60, "
CONSULT Function".
DTC Display Item Malfunction detected condition Possible malfunction
B2268 WATER TEMP METER
[B2268] ECM continuously transmits abnormal engine coolant
temperature signals for 60 seconds or more • Engine coolant temperature sensor
•ECM
Revision: August 2015
2016 Versa Note

cardiagn.com

MWI
STEERING SWITCHMWI-103
< DTC/CIRCUIT DIAGNOSIS > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
STEERING SWITCH
Diagnosis ProcedureINFOID:0000000012432640
Regarding Wiring Diagram information, refer to MWI-79, "Wiring Diagram".
1.CHECK STEERING SWITCH
1. Turn ignition switch OFF.
2. Disconnect combination switch (spiral cable) connector M88.
3. Check for continuity between the termi nals of combination switch connector M88.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace steering switches. Refer to AV-58, "
Removal and Installation".
2.CHECK COMBINATION SWITCH (SPIRAL CABLE)
Check continuity between combination swit ch (spiral cable) connectors M88 and M30.
Is the inspection result normal?
YES >> • Display audio system: Refer to AV-104, "Diagnosis Procedure".
• Navigation system: Refer to AV-224, "
Diagnosis Procedure".
NO >> Replace combination switch (spiral cable). Refer to SR-16, "
Removal and Installation".
Combination switch (spiral cable) connector M88
Condition Continuity
Terminal Terminal
16 17When steering switch is pressed.
Yes
Other than above. No
Combination switch (spiral cable)
Continuity
Connector TerminalConnector Terminal
M88 16
M30 32
Ye s
17 33
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI-110
< SYMPTOM DIAGNOSIS >[TYPE B]
THE DOOR OPEN WARNING CONTINU
ES DISPLAYING, OR DOES NOT DIS-
PLAY
THE DOOR OPEN WARNING CONTIN UES DISPLAYING, OR DOES NOT
DISPLAY
DescriptionINFOID:0000000012432653
• The door ajar warning is displayed even though all of the doors are closed.
• The door ajar warning is not displayed even though a door is ajar.
Diagnosis ProcedureINFOID:0000000012432654
1.CHECK BCM INPUT SIGNAL
Check the BCM input signal. Refer to DLK-98, "
ComponentFunctionCheck" (with Intelligent Key system) or
DLK-232, "
ComponentFunctionCheck" (without Intelligent Key system).
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK COMBINATION METER INPUT SIGNAL
Select the METER/M&A Data Moni tor and check the DOOR W/L monitor value while opening and closing
doors.
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-115, "Removal and Installation".
NO >> Replace BCM. Refer to BCS-74, "
Removal and Installation" (with Intelligent Key system) or BCS-
137, "Removal and Installation" (without Intelligent Key system).
3.CHECK DOOR SWITCH SIGNAL CIRCUIT
Check the door switch signal circuit. Refer to DLK-98, "
Diagnosis Procedure" (with Intelligent Key system) or
DLK-232, "
Diagnosis Procedure" (without Intelligent Key system).
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness or connector.
4.CHECK DOOR SWITCH
Check the door switch. Refer to DLK-99, "
Component Inspection" (with Intelligent Key system) or DLK-234,
"Component Inspection" (without Intelligent Key system).
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-115, "Removal and Installation".
NO >> Replace applicable door switch. Refer to DLK-181, "
Removal and Installation" (with Intelligent Key
system) or DLK-308, "
Removal and Installation" (without Intelligent Key system).
Monitor item Condition Status
DOOR W/L Door open
ON
Door closed OFF
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI
THE PARKING BRAKE RELEASE WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY
MWI-111
< SYMPTOM DIAGNOSIS > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
THE PARKING BRAKE RELEASE WA RNING CONTINUES DISPLAYING,
OR DOES NOT DISPLAY
DescriptionINFOID:0000000012432655
• The parking brake warning is displayed while driving the vehicle even though the parking brake is released.
• The parking brake warning is not displayed while driving the vehicle even though the parking brake is
applied.
Diagnosis ProcedureINFOID:0000000012432656
1.CHECK PARKING BRAKE WARNING LAMP OPERATION
1. Start engine.
2. Check the operation of the brake warni ng lamp while operating the parking brake.
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-115, "Removal and Installation".
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH
Check the parking brake switch. Refer to WCS-44, "
TYPE B : Component Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace parking brake switch. Refer to PB-6, "
Exploded View".
3.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Check the parking brake switch signal circuit. Refer to WCS-43, "
TYPE B : Diagnosis Procedure".
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-115, "Removal and Installation".
NO >> Repair or replace harness or connector.
Condition Warning lamp status
Parking brake applied ON
Parking brake released OFF
Revision: August 2015 2016 Versa Note

cardiagn.com

MWI
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECTMWI-113
< SYMPTOM DIAGNOSIS > [TYPE B]
C
D
E
F
G H
I
J
K L
M B A
O P
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
DescriptionINFOID:0000000012432659
• The displayed outside air temperature is higher than the actual temperature.
• The displayed outside air temperature is lower than the actual temperature.
• Outside air temperature is not indicated.
Diagnosis ProcedureINFOID:0000000012432660
1.CHECK AMBIENT SENSOR SIGNAL CIRCUIT
Check the ambient sensor signal circuit. Refer to MWI-104, "
DiagnosisProcedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness or connector.
2.CHECK AMBIENT SENSOR
Check the ambient sensor. Refer to MWI-105, "
Component Inspection".
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-115, "Removal and Installation".
NO >> Replace ambient sensor. Refer to MWI-116, "
Removal and Installation".
Revision: August 2015 2016 Versa Note

cardiagn.com