2016 NISSAN NOTE ECU

DOOR MIRROR GLASSMIR-17
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
K
M A
B
MIR
N
O P
DOOR MIRROR GLASS
Removal and InstallationINFOID:0000000012432094
REMOVAL
1. Place a piece of protective tape on the mirror housing.
2. Tilt the door mirror glass upward (1).
3. Remove the door mirror glass lower side, using a suitable tool (A) in the recess between door mirror glass (1) and actuator (2)
and push up on pawls and rotate (twist).
4. Disconnect harness connector from door mirror glass (if equipped with heated mirrors).
5. Remove the glass using a suitable tool in the (LH/RH) recesses between door mirror glass and actuator and push up on pawls
and rotate (twist).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
After installation, visually check that pawls are securely engaged.
ALLIA1036ZZ
ALLIA1037ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

PCS
PCS-1
ELECTRICAL & POWER CONTROL
C
DE
F
G H
I
J
K L
B
SECTION PCS
A
O P
N
CONTENTS
POWER CONTROL SYSTEM
IPDM E/R
PRECAUTION ....... ........................................
3
PRECAUTIONS .............................................. .....3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
3
SYSTEM DESCRIPTION ..............................4
COMPONENT PARTS ................................... .....4
Component Parts Location .................................. ......4
SYSTEM ..............................................................5
RELAY CONTROL SYSTEM ................................ ......5
RELAY CONTROL SYSTEM : System Descrip-
tion ...................................................................... ......
5
RELAY CONTROL SYSTEM : Fail-safe ...................6
POWER CONSUMPTION CONTROL SYSTEM ... ......7
POWER CONSUMPTION CONTROL SYSTEM :
System Description ...................................................
8
DIAGNOSIS SYSTEM (IPDM E/R) ......................9
Diagnosis Description ......................................... ......9
CONSULT Function (IPDM E/R) .............................10
ECU DIAGNOSIS INFORMATION ..............13
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) ............. ....
13
Reference Value ................................................. ....13
Fail-safe ..................................................................19
DTC Index ..............................................................20
WIRING DIAGRAM ......................................21
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) ............. ....
21
Wiring Diagram ................................................... ....21
DTC/CIRCUIT DIAGNOSIS .........................26
U1000 CAN COMM CIRCUIT ...........................26
Description ........................................................... ....26
DTC Logic ................................................................26
Diagnosis Procedure ...............................................26
B2098 IGNITION RELAY ON STUCK ..............27
DTC Logic ................................................................27
Diagnosis Procedure ...............................................27
B2099 IGNITION RELAY OFF STUCK ............28
DTC Logic ................................................................28
Diagnosis Procedure ...............................................28
POWER SUPPLY AND GROUND CIRCUIT ....29
Diagnosis Procedure ...............................................29
REMOVAL AND INSTALLATION ...............30
IPDM E/R ...........................................................30
Exploded View ..................................................... ....30
Removal and Installation .........................................30
POWER DISTRIBUTION SYSTEM
PRECAUTION ...... ........................................
32
PRECAUTIONS .................................................32
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ....
32
SYSTEM DESCRIPTION .............................33
COMPONENT PARTS ......................................33
Component Parts Location .................................. ....33
SYSTEM ............................................................34
POWER DISTRIBUTION SYSTEM ........................ ....34
POWER DISTRIBUTION SYSTEM : System De-
scription ............................................................... ....
34
Fail-safe ...................................................................35
Revision: August 2015 2016 Versa Note

cardiagn.com

PCS-2
DIAGNOSIS SYSTEM (BCM) ............................37
COMMON ITEM ..................................................... ...37
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) ....................................................
37
INTELLIGENT KEY ................................................ ...38
INTELLIGENT KEY : CONSULT Function (BCM -
INTELLIGENT KEY) ...............................................
38
ECU DIAGNOSIS INFORMATION ........... ...41
BCM, IPDM E/R .............................................. ...41
List of ECU Reference ......................................... ...41
WIRING DIAGRAM .....................................42
POWER DISTRIBUTION SYSTEM ................ ...42
Wiring Diagram .................................................... ...42
BASIC INSPECTION ...................................50
DIAGNOSIS AND REPAIR WORK FLOW ..... ...50
Work Flow ............................................................ ...50
PROCEDURE FOR TEMPORARILY DIS-
ABLING THE IGNITION BATTERY SAVER
SYSTEM .......................................................... ...
53
Description ........................................................... ...53
Work Procedure ......................................................53
DTC/CIRCUIT DIAGNOSIS ...................... ...54
U1000 CAN COMM CIRCUIT ......................... ...54
Description ........................................................... ...54
DTC Logic ...............................................................54
Diagnosis Procedure ..............................................54
U1010 CONTROL UNIT (CAN) .........................55
DTC Logic ............................................................ ...55
Diagnosis Procedure ..............................................55
B2614 ACC RELAY CIRCUIT ...........................56
DTC Logic ............................................................ ...56
Diagnosis Procedure ..............................................56
B2615 BLOWER RELAY CIRCUIT ...................58
DTC Logic ............................................................ ...58
Diagnosis Procedure ..............................................58
B2616 IGNITION RELAY CIRCUIT ...................60
DTC Logic ............................................................ ...60
Diagnosis Procedure ............................................ ...60
B2618 BCM .......................................................62
DTC Logic ............................................................ ...62
Diagnosis Procedure ...............................................62
B261A PUSH-BUTTON IGNITION SWITCH .....63
DTC Logic ............................................................ ...63
Diagnosis Procedure ...............................................63
B26F1 IGNITION RELAY ..................................65
DTC Logic ...............................................................65
Diagnosis Procedure ...............................................65
B26F2 IGNITION RELAY ..................................66
DTC Logic ...............................................................66
Diagnosis Procedure ...............................................66
B26F6 BCM .......................................................68
DTC Logic ............................................................ ...68
Diagnosis Procedure ...............................................68
PUSH-BUTTON IGNITION SWITCH .................70
Component Function Check ............................... ...70
Diagnosis Procedure ...............................................70
Component Inspection ............................................71
POWER SUPPLY AND GROUND CIRCUIT .....73
BCM ........................................................................ ...73
BCM : Diagnosis Procedure ....................................73
IPDM E/R (INTELLIGENT POWER DISTRIBU-
TION MODULE ENGINE ROOM) ........................... ...
73
IPDM E/R (INTELLIGENT POWER DISTRIBU-
TION MODULE ENGINE ROOM) : Diagnosis Pro-
cedure .....................................................................
73
SYMPTOM DIAGNOSIS ............................75
PUSH-BUTTON IGNITION SWITCH DOES
NOT OPERATE .............................................. ...
75
Description ........................................................... ...75
Diagnosis Procedure ...............................................75
REMOVAL AND INSTALLATION ..............76
BCM (BODY CONTROL MODULE) ............... ...76
Removal and Installation .........................................76
PUSH-BUTTON IGNITION SWITCH .............. ...77
Removal and Installation .........................................77
Revision: August 2015 2016 Versa Note

cardiagn.com

PCS-10
< SYSTEM DESCRIPTION >[IPDM E/R]
DIAGNOSIS SYSTEM (IPDM E/R)
Concept of Auto Active Test
• IPDM E/R starts the auto active test with the door
switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis Chart in Auto Active Test
CONSULT Function (IPDM E/R)INFOID:0000000012433272
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
AWMIA1737GB
Symptom Inspection contentsPossible cause
Any of the following components do not operate:
•Parking lamp
• Side marker lamp
• License plate lamp
•Tail lamp
• Front fog lamp
• Headlamp (HI, LO)
• Front wiper (HI, LO) Perform auto active test.
Does the applicable system op-
erate?YES BCM signal input circuit
NO • Lamp or motor
• Lamp or motor ground circuit
• Harness or connector between
IPDM E/R and applicable system
• IPDM E/R
A/C compressor does not operate Perform auto active test.
Does the magnet clutch oper-
ate?YES
• BCM signal input circuit
• CAN communication signal be-
tween BCM and ECM
• CAN communication signal be-
tween ECM and IPDM E/R
NO • Magnet clutch
• Harness or connector between
IPDM E/R and magnet clutch
• IPDM E/R
Cooling fan does not operate Perform auto active test.
Does the cooling fan operate?YES
• ECM signal input circuit
• CAN communication signal be-
tween ECM and IPDM E/R
NO • Cooling fan motor
• Harness or connector between
IPDM E/R and cooling fan motor
• IPDM E/R
Direct Diagnostic Mode Description
ECU Identification The IPDM E/R part number is displayed.
Self Diagnostic Result The IPDM E/R self diagnostic results are displayed.
Revision: August 2015 2016 Versa Note

cardiagn.com

PCS
DIAGNOSIS SYSTEM (IPDM E/R)PCS-11
< SYSTEM DESCRIPTION > [IPDM E/R]
C
D
E
F
G H
I
J
K L
B A
O P
N
ECU IDENTIFICATION
The IPDM E/R part number is displayed.
SELF DIAGNOSTIC RESULT
Refer to
PCS-20, "DTCIndex".
DATA MONITOR
ACTIVE TEST
Data Monitor The IPDM E/R input/output data is displayed in real time.
Active Test The IPDM E/R activates outputs to test components.
CAN Diag Support Mntr The result of transmit/receive diagnosis of CAN communication is displayed.
Direct Diagnostic Mode
Description
Monitor Item [Unit]Main
Signals Description
MOTOR FAN REQ [1/2/3/4] ×Indicates cooling fan speed signal received from ECM on CAN communication
line
AC COMP REQ [On/Off] ×Indicates A/C compressor request signal received from ECM on CAN commu-
nication line
TAIL&CLR REQ [On/Off] ×Indicates position light request signal
received from BCM on CAN communica-
tion line
HL LO REQ [On/Off] ×Indicates low beam request signal received from BCM on CAN communication
line
HL HI REQ [On/Off] ×Indicates high beam request signal received from BCM on CAN communication
line
FR FOG REQ [On/Off] ×Indicates front fog light request signal received from BCM on CAN communica-
tion line
FR WIP REQ [Stop/1LOW/Low/Hi] ×Indicates front wiper request signal received from BCM on CAN communication
line
WIP AUTO STOP [STOP P/ACT P] ×Indicates condition of front wiper auto stop signal
WIP PROT [Off/BLOCK] ×Indicates condition of front wiper fail-safe operation
IGN RLY1 -REQ [On/Off] Indicates ignition switch ON signal received from BCM on CAN communication
line
IGN RLY [On/Off] ×Indicates condition of ignition relay
PUSH SW [On/Off] Indicates condition of push-button ignition switch
INTER/NP SW [On/Off] Indicates condition of CVT shift position
ST RLY CONT [On/Off] Indicates starter relay status signal received from BCM on CAN communication
line
IHBT RLY -REQ [On/Off] Indicates starter control relay signal received from BCM on CAN communication
line
ST/INHI RLY [Off/ ST /INHI] Indicates condition of starter relay and starter control relay
DETENT SW [On/Off] Indicates condition of CVT shift selector (park position switch)
DTRL REQ [Off] Indicates daytime running light request signal received from BCM on CAN com-
munication line
THFT HRN REQ [On/Off] Indicates theft warning horn request signal received from BCM on CAN commu-
nication line
HORN CHIRP [On/Off] Indicates horn reminder signal received from BCM on CAN communication line
Test item Description
HORN This test is able to check horn operation [On].
FRONT WIPER This test is able to check wiper motor operation [Hi/Lo/Off].
Revision: August 2015 2016 Versa Note

cardiagn.com

PCS
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PCS-13
< ECU DIAGNOSIS INFORMATION > [IPDM E/R]
C
D
E
F
G H
I
J
K L
B A
O P
N
ECU DIAGNOSIS INFORMATION
IPDM E/R (INTELLIGENT POWER
DISTRIBUTION MODULE ENGINE
ROOM)
Reference ValueINFOID:0000000012433273
VALUES ON THE DIAGNOSIS TOOL
Monitor Item ConditionValue/Status
MOTOR FAN REQ Engine idle speed Changes depending on engine cool-
ant temperature, air conditioner op-
eration status, vehicle speed, etc.
1/2/3/4
AC COMP REQ Engine running A/C switch OFF
Off
A/C switch ON
(Compressor is operating) On
TAIL&CLR REQ Lighting switch OFF
Off
Lighting switch 1ST or 2ND On
HL LO REQ Lighting switch OFF
Off
Lighting switch 2ND On
HL HI REQ Lighting switch 2ND Lighting switch other than HI and
PA S S
Off
Lighting switch HI or PASS On
FR FOG REQ Lighting switch 2ND Front fog lamp switch OFF
Off
Front fog lamp switch ON On
FR WIP REQ Ignition switch ON Front wiper switch OFF
Stop
Front wiper switch INT 1LOW
Front wiper switch LO Low
Front wiper switch HI Hi
WIP AUTO STOP Ignition switch ON Front wiper stop position
STOP P
Any position other than front wiper
stop position ACT P
WIP PROT Ignition switch ON Front wiper operates normally.
Off
Front wiper stops at fail-safe opera-
tion. BLOCK
IGN RLY1 -REQ Ignition switch OFF or ACC
Off
Ignition switch ON On
IGN RLY Ignition switch OFF or ACC
Off
Ignition switch ON On
PUSH SW Release the push-button ignition switch
Off
Press the push-button ignition switch On
INTER/NP SW Ignition switch ON Selector lever in any position other
than P or N (CVT models)
Off
Release clutch pedal (M/T models)
Selector lever in P or N position
(CVT models) On
Depress clutch pedal (M/T models)
ST RLY CONT Ignition switch ON
Off
At engine cranking On
Revision: August 2015 2016 Versa Note

cardiagn.com

PCS-14
< ECU DIAGNOSIS INFORMATION >[IPDM E/R]
IPDM E/R (INTELLIGENT POWER DI
STRIBUTION MODULE ENGINE ROOM)
IHBT RLY -REQIgnition switch ON
Off
At engine cranking On
ST/INHI RLY Ignition switch ON
Off
At engine cranking INHI ON → ST ON
The status of starter relay or starter control relay cannot be recognized by
the battery voltage malfunction, etc. when the starter relay is ON and the
starter control relay is OFF. UNKWN
DETENT SW Ignition switch ON • Press the selector button with se-
lector lever in P position.
• Selector lever in any position oth-
er than P. Off
Release the selector button with selector lever in P position. On
DTRL REQ Daytime running lamps OFF
Off
Daytime running lamps ON On
THFT HRN REQ Not operation
Off
• Panic alarm is activated
• Theft warning alarm is activated On
HORN CHIRP Not operated
Off
Door locking with key fob (horn chirp mode) On
Monitor Item
ConditionValue/Status
Revision: August 2015 2016 Versa Note

cardiagn.com

PCS
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PCS-15
< ECU DIAGNOSIS INFORMATION > [IPDM E/R]
C
D
E
F
G H
I
J
K L
B A
O P
N
TERMINAL LAYOUT
PHYSICAL VALUES
ALMIA0600ZZ
Te r m i n a l
Wire
color Circuit
Input/
Output Ignition
switch Condition
Value
1 R Battery power supply Input OFF —Battery voltage
2 Y Battery power supply Input OFF —Battery voltage
3 SB
1
W2Ignition switch power
supply (START) InputOFF
ACC
ON —0
V
START — Battery voltage
5Y Cooling fan power sup-
ply (HIGH) Output
ON
or
START Cooling fan OFF
0V
Cooling fan LO 4 – 8 V
Cooling fan MID or HI Battery voltage
6R Starter motor power
supply
OutputOFF
ACC ON —0
V
START — Battery voltage
Revision: August 2015 2016 Versa Note

cardiagn.com