2016 NISSAN NOTE ignition

B2628 OUTSIDE ANTENNADLK-75
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2628 OUTSIDE ANTENNA
DTC LogicINFOID:0000000012430007
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check “Self Diagnostic Result” of “BCM” using CONSULT.
Is outside key antenna DTC detected?
YES >> Refer to DLK-75, "Diagnosis Procedure".
NO >> Outside key antenna (rear bumper) is OK.
Diagnosis ProcedureINFOID:0000000012430008
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch ON.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> GO TO 2.
2.CHECK OUTSIDE KEY ANTENNA CIRCUIT
1. Turn ignition switch OFF.
DTC CONSULT display
description DTC detecting condition
Possible cause
B2628 OUTSIDE ANTENNA
3 An excessive high or low voltage from outside key
antenna (rear bumper) is sent to BCM. • Outside key antenna (rear
bumper)
• Between BCM – Outside key an- tenna (rear bumper)
(+)
(–) Condition Signal
(Reference value)
BCM
Connector Terminal
M98 82
83
Ground When the back
door request
switch is operat-
ed with ignition
switch OFF. When Intelligent
Key is in the an-
tenna detection
area. (The dis-
tance between
Intelligent Key
and antenna: 80
cm or less.)
When Intelligent
Key is not in the
antenna detec-
tion area. (The
distance be-
tween Intelli-
gent Key and
antenna: Ap-
prox. 2 m.)
JMKIA5955GB
JMKIA5954GB
Revision: August 2015
2016 Versa Note

cardiagn.com

DLK-76
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2628 OUTSIDE ANTENNA
2. Disconnect BCM connector and outside key antenna (rear bumper) connector.
3. Check continuity between BCM harness connector and outside key antenna (rear bumper) harness con-
nector.
4. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 2
1. Replace outside key antenna (rear bumper). (New antenna or other antenna)
2. Connect BCM and outside key antenna (rear bumper) connector.
3. Turn ignition switch ON.
4. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace outside key antenna (rear bumper). Refer to DLK-184, "REAR BUMPER : Removal and
Installation".
NO >> Replace BCM. Refer to BCS-74, "
Removal and Installation".
BCM Outside key antenna (rear bumper)
Continuity
Connector TerminalConnector Terminal
M98 82
B49 1
Ye s
83 2
BCM GroundContinuity
Connector Terminal
M98 82
No
83
(+)
(–) Condition Signal
(Reference value)
BCM
Connector Terminal
M98 82
83Ground When the back
door request
switch is operat-
ed with ignition
switch OFF. When Intelligent
Key is in the an-
tenna detection
area. (The dis-
tance between
Intelligent Key
and antenna: 80
cm or less.)
When Intelligent
Key is not in the
antenna detec-
tion area. (The
distance be-
tween Intelli-
gent Key and
antenna: Ap-
prox. 2 m.)
JMKIA5955GB
JMKIA5954GB
Revision: August 2015
2016 Versa Note

cardiagn.com

DOOR LOCK ACTUATORDLK-79
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
DOOR LOCK ACTUATOR
DRIVER SIDE
DRIVER SIDE : Comp onent Function CheckINFOID:0000000012430012
1.CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR LOCK” in “Active Test”.
3. Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES >> Door lock actuator is OK.
NO >> Refer to DLK-79, "
DRIVER SIDE : Diagnosis Procedure".
DRIVER SIDE : Diag nosis ProcedureINFOID:0000000012430013
Regarding Wiring Diagram information, refer to DLK-36, "Wiring Diagram".
1.CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock actuator LH connector.
3. Check voltage between front door lock actuator LH harness connector and ground.
Is the inspection result normal?
YES >> Replace front door lock actuator LH .
NO >> GO TO 2.
2.CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector and all door lock actuator connectors.
2. Check continuity between BCM harness connector and front door lock actuator LH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK BCM OUTPUT SIGNAL
(+)
(–) Condition Voltag e
(Approx.)
Front door lock actuator
LH
Connector Terminal
D14 1
Ground Door lock and unlock switch Lock
Battery voltage
2 Unlock
BCMFront door lock actuator LH
Continuity
Connector TerminalConnector Terminal
M99 65
D14 1
Ye s
66 2
BCM GroundContinuity
Connector Terminal
M99 65
No
66
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-80
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
1. Connect BCM connector.
2. Check voltage between front door lock
actuator LH harness connector and ground.
Is the inspection result normal?
YES >> Check for internal short of each door lock actuator.
NO >> Replace BCM. Refer to BCS-74, "
Removal and Installation".
PASSENGER SIDE
PASSENGER SIDE : Component Function CheckINFOID:0000000012430014
1.CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR LOCK” in “Active Test”.
3. Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES >> Door lock actuator is OK.
NO >> Refer to DLK-80, "
PASSENGER SIDE : Diagnosis Procedure".
PASSENGER SIDE : Diagnosis ProcedureINFOID:0000000012430015
Regarding Wiring Diagram information, refer to DLK-36, "Wiring Diagram".
1.CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock actuator RH connector.
3. Check voltage between front door lock actuator RH harness connector and ground.
Is the inspection result normal?
YES >> Replace front door lock actuator RH.
NO >> GO TO 2.
2.CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector and all door lock actuators.
2. Check continuity between BCM harness connector and front door lock actuator RH harness connector.
3. Check continuity between BCM harness connector and ground.
(+) (–) Condition Vo l ta g e
(Approx.)
BCM
Connector Terminal
M99 65
Ground Door lock and unlock switch Lock
Battery voltage
66 Unlock
(+)
(–) Condition Voltag e
(Approx.)
Front door lock actuator
RH
Connector Terminal
D114 2
Ground Door lock and unlock switch Lock
Battery voltage
1U nlo ck
BCM Front door lock actuator RH
Continuity
Connector TerminalConnector Terminal
M99 65
D114 2
Ye s
59 1
Revision: August 2015 2016 Versa Note

cardiagn.com

DOOR LOCK ACTUATORDLK-81
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between front door lock actuator RH harness connector and ground.
Is the inspection result normal?
YES >> Check for internal short of each door lock actuator.
NO >> Replace BCM. Refer to BCS-74, "
Removal and Installation".
REAR LH
REAR LH : Component Function CheckINFOID:0000000012430016
1.CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR LOCK” in “Active Test”.
3. Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES >> Door lock actuator is OK.
NO >> Refer to DLK-81, "
REAR LH : Diagnosis Procedure".
REAR LH : Diagnosis ProcedureINFOID:0000000012430017
Regarding Wiring Diagram information, refer to DLK-36, "Wiring Diagram".
1.CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear door lock actuator LH connector.
3. Check voltage between rear door lock actuator LH harness connector and ground.
Is the inspection result normal?
YES >> Replace rear door lock actuator LH. Refer to DLK-172, "Exploded View".
NO >> GO TO 2.
BCM
GroundContinuity
Connector Terminal
M99 65
No
59
(+)
(–) Condition Vo l ta g e
(Approx.)
BCM
Connector Terminal
M99 65
Ground Door lock and unlock switch Lock
Battery voltage
59 Unlock
(+)
(–) Condition Vo l ta g e
(Approx.)
Rear door lock actuator LH
Connector Terminal
D205 1
Ground Door lock and unlock switch Lock
Battery voltage
2 Unlock
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-82
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
2.CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector and all door lock actuator connectors.
2. Check continuity between BCM harness connector and rear door lock actuator LH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between rear door lock actuator LH harness connector and ground.
Is the inspection result normal?
YES >> Check for internal short of each door lock actuator.
NO >> Replace BCM. Refer to BCS-74, "
Removal and Installation".
REAR RH
REAR RH : Component Function CheckINFOID:0000000012430018
1.CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR LOCK” in “Active Test”.
3. Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES >> Door lock actuator is OK.
NO >> Refer to DLK-82, "
REAR RH : Diagnosis Procedure".
REAR RH : Diagnosis ProcedureINFOID:0000000012430019
Regarding Wiring Diagram information, refer to DLK-36, "Wiring Diagram".
1.CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear door lock actuator RH connector.
3. Check voltage between rear door lock actuator RH harness connector and ground.
BCM Rear door lock actuator LH
Continuity
Connector TerminalConnector Terminal
M99 65
D205 1
Ye s
55 2
BCM GroundContinuity
Connector Terminal
M99 65
No
55
(+)
(–) Condition Vo l ta g e
(Approx.)
BCM
Connector Terminal
M99 65
Ground Door lock and unlock switch Lock
Battery voltage
55 Unlock
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-84
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
YES >> Back door lock actuator is OK.
NO >> Refer to
DLK-84, "
BACK DOOR : Diagnosis Procedure".
BACK DOOR : Diagnosis ProcedureINFOID:0000000012430022
Regarding Wiring Diagram information, refer to DLK-36, "Wiring Diagram".
1.CHECK BACK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect back door lock actuator connector.
3. Check voltage between back door lock actuator harness connector and ground.
Is the inspection result normal?
YES >> Replace back door lock actuator. Refer to DLK-176, "BACK DOOR LOCK : Removal and Installa-
tion".
NO-1 >> GO TO 2 (lock signal).
NO-2 >> GO TO 3 (unlock signal).
2.CHECK BACK DOOR LOCK ACTUATOR LOCK CIRCUIT
1. Disconnect BCM connector and all door lock actuator connectors.
2. Check continuity between BCM harness connecto r and back door lock actuator harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK BACK DOOR LOCK ACTUATOR UNLOCK CIRCUIT
1. Disconnect back door lock actuator relay connector.
2. Check continuity between back door lock actuator relay harness connector and back door lock actuator
harness connector.
3. Check continuity between BCM harness connector and ground.
(+)
(–) Condition Voltage (V)
(Approx.)
Back door lock actuator
Connector Terminal
D505 1
Ground Door lock and unlock switch Unlock
Battery voltage
2L ock
BCM Back door lock actuator
Continuity
Connector TerminalConnector Terminal
M99 65D505 2Yes
BCM GroundContinuity
Connector Terminal
M99 65 No
Back door lock actuator relayBack door lock actuator
Continuity
Connector TerminalConnector Terminal
M41 3D505 1Yes
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-86
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR LOCK ACTUATOR RELAY
BACK DOOR LOCK ACTUATOR RELAY
DescriptionINFOID:0000000012430023
Controls back door lock actuator lock/unlock operation.
Component Function CheckINFOID:0000000012430024
1.CHECK FUNCTION
1. Perform “DOOR LOCK” in “Active Test” using CONSULT.
2. Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES >> Back door lock actuator relay is OK.
NO >> Refer to DLK-86, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430025
Regarding Wiring Diagram information, refer to DLK-36, "Wiring Diagram".
1.CHECK FUSE
1. Turn ignition switch OFF.
2. Check 10 A fuse, No. 8, located in fuse block (J/B).
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.CHECK BACK DOOR LOCK ACTUATOR RELAY POWER CIRCUIT
1. Remove back door lock actuator relay.
2. Check voltage between back door lock actuator relay harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK BACK DOOR LOCK ACTUATOR RELAY CIRCUIT 1
1. Install the back door lock actuator relay.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 6.
NO-1 (when voltage is fixed at 12V)>>Replace BCM. Refer to BCS-74, "
Removal and Installation".
NO-2 (when voltage is fixed at 0V)>>GO TO 4.
(+)
(–)Voltage (V)
(Approx.)
Back door lock actuator relay
Connector Terminal
M41 1
Ground Battery voltage
5
(+)
(–) Condition Voltage (V)
(Approx.)
BCM
Connector Terminal
M100 50GroundDoor lock and un-
lock switch LOCK Battery voltage
UNLOCK 0
Revision: August 2015 2016 Versa Note

cardiagn.com