2016 NISSAN NOTE ignition

BACK DOOR REQUEST SWITCHDLK-97
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Check continuity between back door request switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK BACK DOOR REQUEST SWITCH
Refer to DLK-97, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace back door request switch. Refer to DLK-176, "
OUTSIDE HANDLE : Removal and Instal-
lation".
5.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> Inspection End.
Component InspectionINFOID:0000000012430036
1.CHECK BACK DOOR REQUEST SWITCH
1. Turn ignition switch OFF.
2. Disconnect back door request switch connector.
3. Check continuity between back door request switch terminals.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace back door request switch. Refer to DLK-176, "
OUTSIDE HANDLE : Removal and Instal-
lation".
Back door request switch
GroundContinuity
Connector Terminal
D506 2 Yes
Back door request switch
ConditionContinuity
Te r m i n a l
1 2Back door request switch Pressed
Yes
Released No
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-98
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR SWITCH
DOOR SWITCH
Component Function CheckINFOID:0000000012430037
1.CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “DOOR SW-DR”, “DOOR SW-AS”, “DOOR SW-RL” and “DOOR SW-RR” in “Data Monitor”.
3. Check that the function operates normall y according to the following conditions:
Is the inspection result normal?
YES >> Door switch is OK.
NO >> Refer to DLK-98, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430038
Regarding Wiring Diagram information, refer to DLK-36, "Wiring Diagram".
1.CHECK DOOR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect malfunctioning door switch connector.
3. Check signal between malfunctioning door swit ch harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK DOOR SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between door switch harness connector and BCM harness connector.
Monitor item Condition Status
DOOR SW-DR Front door LH Open
ON
Closed OFF
DOOR SW-AS Front door RH Open
ON
Closed OFF
DOOR SW-RL Rear door LH Open
ON
Closed OFF
DOOR SW-RR Rear door RHOpen
ON
Closed OFF
(+)
(–)Signal
(Reference value)
Door switch
Connector Terminal
Front door switch
LH B8
3
Ground
7.0 - 8.0 V
Front door switch
RH
B16
3
Rear door switch
LH B6
3
Rear door switch
RH B17
3
PKIB4960J
Revision: August 2015 2016 Versa Note

cardiagn.com

DOOR SWITCHDLK-99
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
3. Check continuity between door switch harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK DOOR SWITCH
Refer to DLK-99, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace malfunctioning door switch.
4.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> Inspection End.
Component InspectionINFOID:0000000012430039
1.CHECK DOOR SWITCH
1. Turn ignition switch OFF.
2. Disconnect malfunctioning door switch connector.
3. Check continuity between door switch terminals.
Is the inspection result normal?
Door switch BCM
Continuity
Connector TerminalConnector Terminal
Front door switch
LH B8
3M10 0 47
Ye s
Front door switch
RH
B16
45
Rear door switch
LH B6
48
Rear door switch
RH B17
46
Door switch GroundContinuity
Connector Terminal
Front door switch LH B8
3N o
Front door switch RH
B16
Rear door switch LH B6
Rear door switch RH B17
Door switch
Condition Continuity
Te r m i n a l
Front door switch
LH
3Ground part of door
switch Door switch Pressed
No
Released Yes
Front door switch
RH Pressed
No
Released Yes
Rear door switch
LH Pressed
No
Released Yes
Rear door switch
RH Pressed
No
Released Yes
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-102
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER
Component Function CheckINFOID:0000000012542553
1.CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “OUTSIDE BUZZER ” in “ACTIVE TEST” mode.
3. Touch “On” or “Off” to check that it works normally.
Is the inspection result normal?
YES >> Intelligent Key warning buzzer is OK.
NO >> Refer to DLK-102, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012542554
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK FUSE
1. Turn ignition switch OFF.
2. Check 10 A fuse [No. 8, located in fuse block (J/B)].
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.CHECK INTELLIGENT KEY WARNING BUZZER POWER SUPPLY CIRCUIT
1. Disconnect Intelligent Key warning buzzer connector.
2. Check voltage between Intelligent Key warning buzzer harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK INTELLIGENT KEY WARNING BUZZER CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and Intelligent Key warning buzzer harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK INTELLIGENT KEY WARNING BUZZER
(+)
(–)Vol tag e
(Approx.)
Intelligent Key warning buzzer
Connector Terminal
E70 1Ground Battery voltage
BCM Intelligent Key warning buzzer
Continuity
Connector TerminalConnector Terminal
M98 93E70 3Yes
BCM GroundContinuity
Connector Terminal
M98 93 No
Revision: August 2015 2016 Versa Note

cardiagn.com

INTELLIGENT KEY WARNING BUZZERDLK-103
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Refer to DLK-103, "Component Inspection".
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> Replace Intelligent Key warning buzzer. Refer to DLK-186, "
Removal and Installation".
Component InspectionINFOID:0000000012542555
1.CHECK INTELLIGENT KEY WARNING BUZZER
1. Turn ignition switch OFF.
2. Disconnect Intelligent Key warning buzzer connector.
3. Connect battery power supply directly to Intelligent Key warning buzzer terminals and check the opera- tion.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace Intelligent Key warning buzzer. Refer to DLK-186, "
Removal and Installation".
Intelligent Key warning buzzer
Operation
Te r m i n a l
(+) (− )
1 3Buzzer sounds
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-106
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY RECEIVER
REMOTE KEYLESS ENTRY RECEIVER
Component Function CheckINFOID:0000000012430046
1.CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “RKE OPE COUN1” in “Data Monitor”.
3. Check that the function operates normall y according to the following conditions:
Is the inspection result normal?
YES >> Remote keyless entry receiver is OK.
NO for USA >>Refer to DLK-106, "
Diagnosis Procedure (For USA)".
NO for Canada>>Refer to DLK-107, "
Diagnosis Procedure (For Canada)".
Diagnosis Procedure (For USA)INFOID:0000000012430047
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> GO TO 2.
2.CHECK REMOTE K EYLESS ENTRY RECEIVER CIRCUIT
1. Disconnect BCM and remote keyless entry receiver connectors.
2. Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
Monitor item Condition
RKE OPE COUN1 Checks whether value changes when operating Intelligent Key.
(+)
(–)Condition Signal
(Reference value)
BCM
Connector Terminal
M97 38GroundPush-button igni-
tion OFF or ACC
0 – 0.5 V
Push-button igni-
tion ON Battery voltage
BCM
Remote keyless entry receiver
Continuity
Connector TerminalConnector Terminal
M 973 8M 94 2 Y es
(+) (–)Continuity
BCM
Connector Terminal
M97 38Ground No
Revision: August 2015 2016 Versa Note

cardiagn.com

REMOTE KEYLESS ENTRY RECEIVERDLK-107
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
NO >> Repair or replace harness.
3.CHECK REMOTE KEYLESS ENTRY RECEIVER POWER SUPPLY
Check voltage between remote keyless entry receiver harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO-1 >> Check 10A fuse No. 10 located in fuse block J/B.
NO-2 >> Repair or replace harness between remote keyless entry receiver and 10A fuse No. 10.
4.CHECK REMOTE KEYLESS ENTR Y RECEIVER GROUND CIRCUIT
Check continuity between remote keyles s entry receiver harness connector and ground.
Is the inspection result normal?
YES >> Replace remote keyless entry receiver. Refer to DLK-187, "Removal and Installation".
NO >> Repair or replace harness.
Diagnosis Procedure (For Canada)INFOID:0000000012430048
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between remote keyless entry receiver connector and ground with oscilloscope.
(+)
(–)Vo l ta g e
Approx.
Remote keyless entry receiver
Connector Terminal
M94 1Ground Battery voltage
Remote keyless entry receiver
GroundContinuity
Connector Terminal
M94 4 Yes
Revision: August 2015 2016 Versa Note

cardiagn.com

IGNITION POSITION WARNING FUNCTION DOES NOT OPERATE
DLK-119
< SYMPTOM DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
IGNITION POSITION WARNING FUNCTION DOES NOT OPERATE
Diagnosis ProcedureINFOID:0000000012430069
1.CHECK POWER DOOR LOCK OPERATION
Check power door lock operation.
Does door lock/unlock with driver side door lock knob and door key cylinder?
YES >> GO TO 2.
NO >> Refer to DLK-115, "
Diagnosis Procedure".
2.CHECK DOOR SWITCH
Check door switch.
Refer to DLK-98, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.REPLACE BCM
1. Replace BCM. Refer to BCS-74, "
Removal and Installation".
2. Confirm the operation after replacement.
Is the result normal?
YES >> Inspection End.
NO >> Check intermittent incident. Refer to GI-42, "
Intermittent Incident".
Revision: August 2015 2016 Versa Note

cardiagn.com