2016 Citroen C4 PICASSO check engine

44
C4-Picasso-II_en_Chap01_instruments-bord_ed01-2016
In the event of a fault with the SCR emissions control system
In the event of the detection of a fault
The  AdBlue,   SERVICE   and   diagnostic  
w

arning   lamps   come   on,   accompanied   by   an  
a

udible   signal   and   the   display   of   the   message  
"

Emissions
 f
ault".
The
  alert   is   triggered   when   driving   when   the  
f

ault is detected for the first time, then when
switching
  on   the   ignition   for   subsequent  
j

ourneys,   while   the   fault   persists. During an authorised driving phase (between
650 miles and 0 miles) (1 100 km and 0 km)
If a fault with the SCR system is confirmed
(after
  30   miles   (50   km)   covered   with   the  
p

ermanent   display   of   the   message   signalling  
a

  fault),   the   SERVICE   and   engine   diagnostic  
w

arning   lamps   come   on   and   the   AdBlue  
w

arning   lamp   flashes,   accompanied   by   an  
a

udible   signal   and   the   display   of   a   message  
(

e.g.   "Emissions   fault:   Starting   prevented   in  
1

50   miles")   indicating   the   remaining   range  
e

xpressed   in   miles   or   kilometres.
While
  driving,   the   message   is   displayed   every
 3

0   seconds   while   the   fault   with   the   SCR   system
 p

ersists.
The alert is repeated when switching on the ignition.You should go to a CITROËN dealer or a qualified   workshop   as   soon   as   possible.
Other wise, you will not be able to restart your
engine.
A
 
system
 
that
 
prevents
 
engine
 
starting
 
is
 
activated   automatically   from   650   miles   (1   100   km)   after   confirmation   of   a   fault   with   the   SCR   emissions  
c

ontrol
 
system.
 
Have
 
the
 
system
 
checked
 
by
 
a   CITROËN   dealer   or   a   qualified   workshop   as   soon   as   possible.
If it is a temporary fault, the alert
disappears
 
during
 
the
 
next
 
journey,
 a
fter
 
self-diagnosis
 
of
 
the
 
SCR
 
system. Starting prevented
Every
  time   the   ignition   is   switched   on,   the  
S

ERVICE   and   engine   diagnostic   warning  
l

amps   come   on   and   the   AdBlue   warning   lamp  
f

lashes,   accompanied   by   an   audible   signal   and  
t

he   display   of   the   message   "Emissions   fault:  
St

arting
 p
revented".
You   have   exceeded   the   authorised  
d

riving   limit:   the   starting   prevention  
s

ystem   inhibits   engine   starting.
To   be   able   to   start   the   engine,   you   must  
c

all on a CITROËN dealer or a qualified
workshop.
Instruments

93
C4-Picasso-II_en_Chap03_ergonomie-confort_ed01-2016
In order for these systems to be fully effective, follow the operation and maintenance
guidelines below:
F
 
T
o   obtain   an   even   air   distribution,   take   care   not   to   obstruct   the   exterior   air   intake   grilles  
l

ocated at the base of the windscreen, the nozzles, the vents and the air outlets, as well
as
  the   air   extractor   located   in   the   boot.
F
 
D
o   not   cover   the   sunshine   sensor,   located   on   the   dashboard;   this   is   used   for   regulation  
o

f   the   air   conditioning   system.
F
 
O
perate   the   air   conditioning   system   for   at   least   5   to   10   minutes,   once   or   twice   a   month  
t

o   keep   it   in   per fect   working   order.
F
 
E
nsure   that   the   passenger   compartment   filter   is   in   good   condition   and   have   the   filter  
e

lements   replaced   regularly.
 W

e   recommend   the   use   of   a   combined   passenger   compartment   filter.   Thanks   to   its  
s

pecial active additive, it contributes to the purification of the air breathed by the
occupants
  and   the   cleanliness   of   the   passenger   compartment   (reduction   of   allergic  
s

ymptoms,   bad   odours   and   greasy   deposits).
F
 
T
o   ensure   correct   operation   of   the   air   conditioning   system,   you   are   also   advised   to   have  
i

t   checked   regularly   as   recommended   in   the   maintenance   and   warranty   guide.
F

I
f the system does not produce cold air, switch it off and contact a CITROËN dealer or a
qualified
 w

orkshop.
Recommendations for ventilation and air conditioning
If after an extended stop in sunshine, the  i nterior  t emperature  i s  v ery  h igh,  f irst  
v

entilate   the   passenger   compartment   for  
a

  few   moments.
Put
  the   air   flow   control   at   a   setting   high  
e

nough   to   quickly   change   the   air   in   the  
p

assenger
 c
ompartment.
The
  air   conditioning   system   does   not  
c

ontain chlorine and does not present
any
  danger   to   the   ozone   layer.
The condensation created by the air
conditioning
  results   in   a   discharge  
o

f water under the vehicle which is
per fectly
  normal.
When
 
towing
 
the
 
maximum
 
load
 
on
 
a
 
steep
 
gradient
 
in
 
high
 
temperatures,
 
switching
 
off
 
the
 
a

ir
 
conditioning
 
increases
 
the
 
available
 
engine
 
power
 
and
 
so
 
improves
 
the
 
towing
 
ability.
Stop & Start
The heating and air conditioning s ystems   only   work   when   the   engine   is  
r

unning.
To maintain a comfortable temperature
in
  the   passenger   compartment,   you   can  
t

emporarily deactivate the Stop & Start
system.
For more information on Stop & Star t ,
refer
  to   the   corresponding   section.
3
Ease of use and comfort

108
C4-Picasso-II_en_Chap03_ergonomie-confort_ed01-2016
Central storage compartment
F To  open   the   central   storage   compartment,  p
ull   the   grip   and   lower   the   cover.
It
  is   illuminated   on   opening.
A
  button   on   the   upper   part   allows   the   lighting   to  
b

e   deactivated.
230 V / 50 Hz power socket
A 230 V / 50 Hz socket (maximum power: 120 W) is   fitted   in   the   central   storage   box.
To
  use   the   socket:
F
 
o
pen   the   central   storage   box,
F
 
c
heck   that   the   warning   lamp   is   on   green,
F

c
onnect your multimedia or other electrical
device
  (telephone   charger,   laptop  
c

omputer, CD-DVD player, baby food
warmer...).
This
  socket   works   with   the   engine   running,   as  
w

ell   as   in   STOP   mode   with   Stop   &   Start.
Depending
 
on
 
equipment,
 
it
 
may
 
contain:
-
 
o

ne
 
230
 
V
 
socket,
-
 
o

ne
 
12
 
V
 
socket,
-

o

ne USB port,
-
 
o

ne
 
auxiliary
 
socket In
  the   event   of   a   fault   with   the   socket,   the   green  
w

arning
 lam
p
 f
lashes.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop. Connect only one device at a time to
the
  socket   (no   extension   or   multi-way  
c

onnector).
Connect only devices with class II
insulation   (shown   on   the   device).
As a safety measure, when electrical
consumption   is   high   and   when   required  
b

y   the   vehicle's   electrical   system  
(

particular weather conditions, electrical
overload...),   the   current   supply   to   the  
s

ocket   will   be   cut   off;   the   green   warning  l
amp   goes   off.
Ease of use and comfort

124
C4-Picasso-II_en_Chap04_conduite_ed01-2016
When towing
Distribution of loads
F Distribute the load in the trailer so that the heaviest items are as close as possible to
the
  axle   and   the   nose   weight   approaches   the
 m

aximum   permitted   without   exceeding   it.
Air density decreases with altitude, thus
reducing
  engine   per formance.   Above  
1 0

00 metres,   the   maximum   towed   load   must  
b

e reduced by 10 % for every 1 000 metres of
altitude.
Side wind
F Take   into   account   the   increased   sensitivity  t
o   side   wind.
For more information on Weights
, refer
to   the   corresponding   section.
The   rear   parking   sensors   will   be  
d

eactivated automatically to avoid the
audible
  signal   if   a   genuine   CITROËN  
t

owbar   is   used.
Cooling
Towing a trailer on a slope increases the temperature   of   the   coolant.
As
  the   fan   is   electrically   controlled,   its   cooling  
c

apacity   is   not   dependent   on   the   engine   speed.
F
 
T
o   lower   the   engine   speed,   reduce   your  
s

peed.
The
  maximum   towed   load   on   a   long   incline  
d

epends   on   the   gradient   and   the   ambient  
t

emperature.
In
  all   cases,   keep   a   check   on   the   coolant  
t

emperature. F
 
I
f   the   warning   lamp   and   the  
S

TOP
 
warning   lamp   come   on,  
s

top the vehicle and switch off
the
  engine   as   soon   as   possible.
Braking
Towing a trailer increases the braking distance.
T o   avoid   overheating   of   the   brakes,   the   use   of  
e

ngine   braking   is   recommended.
Ty r e s
F Check  the   tyre   pressures   of   the   towing  v
ehicle   and   of   the   trailer,   observing   the  
re

commended
 p
ressures.
Lighting
F Check  the   electrical   lighting   and   signalling  o
n the trailer and the headlamp beam
height
  of   your   vehicle.
For more information on Adjusting the
headlamp beam height , refer to the
corresponding
 s

ection.
Driving

132
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Label on door panel
Before leaving the vehicle, check that   the   parking   brake   is   applied:   the  
in

dicator lamps in the instrument panel
and
  the   control   lever   must   be   on   fixed,  
n

ot
 f
lashing.
If
  the   parking   brake   is   not   applied,   there  
i

s   an   audible   signal   and   a   message   is  
d

isplayed   on   opening   the   driver's   door.
Never leave a child alone inside the
vehicle
  with   the   ignition   on,   as   they  
c

ould   release   the   parking   brake.When
  towing,   parking   on   a   steep   slope,  o
r if your vehicle is heavily laden,
turn
  the   wheels   towards   the   kerb   and  
e

ngage   a   gear   (with   a   manual   gearbox)  
o

r   place   the   gear   selector   at   position P
with
  an   automatic   gearbox.
For
  towing,   your   vehicle   is   approved   for  
p

arking   on   slopes   of   up   to   12%.
Manual operation
Application of the parking brake is confirmed by illumination of
the
  brake   indicator   lamp   and  
t

he P indicator lamp in the control
lever, accompanied by the display of
the
 m

essage
 "
Parking
 b
rake
 a
pplied".
Manual release
With the ignition on or the engine running, to release   the   parking   brake:
F
 
p
ress   the   brake   pedal,
F
 
w
hile   maintaining   pressure   on   the   brake  
p

edal,   briefly   push   the   control   lever.
The
  complete   release   of   the   parking   brake  
i

s   confirmed   by   the   brake   indicator   lamp   and  
t

he P indicator   lamp   in   the   control   lever   going  
o

ff,  
a
ccompanied  
b
y  
t
he  
d
isplay  
o
f  
t
he  
m
essage  
"

Parking   brake   released".
If you push the control lever without
pressing
  the   brake   pedal,   the   parking  
b

rake   will   not   be   released   and   a  
m

essage   is   displayed.
Manual application
With the vehicle stationary: briefly pull the control lever.
Confirmation of the command is signalled by flashing   of   the   indicator   lamp   in   the   control  
l

eve r.
Driving

133
C4-Picasso-II_en_Chap04_conduite_ed01-2016
With the vehicle stationary, the parking brake is automatically applied when the engine
is switched off
  by   pressing   the   START/STOP  
b

utton. Application
  of   the   parking   brake  
i

s confirmed by illumination of the
brake
  indicator   lamp   and   the   P
indicator lamp in the control lever,
accompanied by the display of the
message
  "Parking   brake   applied".
With
  the   engine   stalled   or   in   STOP  
m

ode of Stop & Start, automatic
application
  does   not   take   place.
In automatic mode, you can manually
apply
 
o
r  
r
elease  
t
he  
p
arking  
b
rake  
u
sing  
t

he   control   lever.
Automatic operation
Automatic release
The complete release of the parking brake   is   confirmed   by   the   brake  
i

ndicator lamp and the P indicator
lamp
  in   the   control   lever   going   off,  
a

ccompanied by the display of the
message
  "Parking   brake   released".
When stationary with the engine running, do not depress the accelerator pedal unnecessarily,
you
  risk   releasing   the   parking   brake.
Ensure first that the engine is running and the driver's   door   is   properly   closed.
The
  electric   parking   brake   releases
automatically and progressively when you
press
  the   accelerator   :
F
 
M
anual   gearbox:   fully   depress   the   clutch  
p

edal,   engage   1
st or reverse gear; press t
he accelerator pedal and let up the clutch
pedal.
F
 
A

utomatic
 
gearbox:   select   position   D, M or
R
 
then
 
press
 
the
  accelerator.
Automatic application
With an automatic gearbox, if the brake d oes   not   release   automatically,   check  
t

hat   the   front   doors   are   correctly   closed.
4
Driving

142
C4-Picasso-II_en_Chap04_conduite_ed01-2016
F Check  that   the   symbol   displayed   in   the  i
nstrument   panel   agrees   with   the   position  
o

f   the   selector.
F
 
P
rogressively   release   the   brake   pedal.
F
 
I
f   the   parking   brake   is   released,   the   vehicle  
m

oves   off.
 I

f   the   parking   brake   is   applied   and  
a

utomatic operation is activated, accelerate
away.
Never
  press   the   accelerator   and   brake  
p

edals   at   the   same   time.   Braking   and  
a

cceleration should be done only with
the
  right   foot.   Pressing   both   pedals  
t

ogether   risks   damaging   the   gearbox.
If
  the   brake   does   not   release  
a

utomatically,   check   that   the   front   doors  
a

re   correctly   closed. Never leave children unsupervised in
the
  vehicle   when   the   engine   is   running.
When
  carrying   out   a   maintenance  
o

peration   with   the   engine   running,  
a
pply  
t

he   parking   brake   and   select   position   P. Never select position P or R unless the
vehicle is at a complete stop with the
brake
 a

pplied.
When
  you   want   to   engage   reverse,  
t

o   avoid   jolts,   do   not   accelerate  
i

mmediately   after   engaging   R.
Changing
 in

to
 p
osition
 R
is
accompanied
  by   an   audible   signal.
Never select position N
  when   driving.  
I

f position N is   engaged   in   error   when  
m

oving,   allow   the   engine   to   idle,   then  
e

ngage   position   D   to   accelerate.
When
  the   engine   is   running   at   idle,  
b

rakes   released,   if   position   R, D or M is
selected, the vehicle will move even if
the
  accelerator   is   not   pressed.
Driving

144
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Before switching off the engine, you can change   to   position   P or N   to   be   in   neutral.  
I

n   either   case,   apply   the   parking   brake   to  
i

mmobilise   the   vehicle,   unless   it   is   programmed  
i

n   automatic   mode.
If the lever is not in position P ,
  on   opening   the  
d

river's   door   or   approximately   45   seconds   after  
s

witching   off   the   ignition   there   is   an   audible  
s

ignal   and   a   message   appears:
F
 
m
ove   the   gear   selector   to   position   P;   the  
a

udible   signal   stops   and   the   message  
d

isappears.
Operating fault
Whenever parking, you must apply the parking brake   to   immobilise   the   vehicle,   if   automatic  
o

peration   has   been   deactivated.
Parking the vehicle
In all circumstances, ensure that the
gear  selector   is   in   position   P before
leaving
  your   vehicle. In the event of a fault with the
gearbox,
  the   service   warning   lamp  
c

omes on in the instrument panel,
accompanied   by   a   message   and   an  
a

udible
 s
ignal.
In   this   case   the   gearbox   goes   into   back-up  
m

ode   and   stays   in   3
rd gear. You may then feel a n
oticeable
 
jolt
 
when
 
going   from   P to R and from
N to R .
 
This
 
jolt
 
does
  not   present   any   risk   to   the  
g

earbox.
Do
 
not
 
exceed
 
60
 
mph   (100   km/h)   while   also  
o

bserving
 
legal
 
speed   limits.
Have
 
it
 
checked
 
by
 
a
  CITROËN   dealer   or   a  
q

ualified
 w

orkshop.
In the event of a battery failure, use the
chock
 
to
 
immobilise
 
the
 
vehicle.
Driving