2016 Citroen C4 PICASSO jump cable

316
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
F Start  the   engine   of   the   vehicle   with   the  g
ood   battery   and   leave   it   running   for   a   few  
m

inutes.
F
 
O
perate   the   starter   on   the   broken   down  
v

ehicle   and   let   the   engine   run.
 I

f   the   engine   does   not   start   straight   away,  
s

witch   off   the   ignition   and   wait   a   few  
m

oments   before   trying   again.
F
 
W
ait   until   the   engine   returns   to   idle   then  
d

isconnect   the   jump   lead   cables   in   the  
r

everse
 o
rder.
F

R
efit the plastic cover to the (+) terminal, if
your
  vehicle   has   one.
F
 
A
llow   the   engine   to   run   for   at   least  
3

0 minutes,   by   driving   or   with   the   vehicle  
s

tationary, so that the battery reaches an
adequate
  state   of   charge.
Starting using another battery
Some functions, including Stop & Start, are not available if the battery is not
sufficiently
 c

harged.
F

R

aise the plastic cover on the (+) terminal,
if
 
your
 
vehicle
 
has
 
one.
F

C

onnect the red cable to the positive
terminal (+) of the flat battery A (at the metal
elbow) then to the positive terminal

(+) of the
slave battery B
 

or
 
the
 
booster.
F
 
C

onnect
 
one
 
end
 
of
 
the
 
green
 
or
 
black
 
c

able
 
to
 
the
 
negative
 
terminal
 
(-)
 
of
 
the
 
s

lave battery B or the booster (or earth
point
 
on
 
the
 
other
 
vehicle).
F
 
C

onnect
 
t

he
 
o

ther
 
e

nd
 
o

f
 
t

he
 
g

reen
 
o

r
 
b

lack
 
c

able to the earth point C
 
on
 
the
 
broken
 
d

own
 
vehicle.
Never
 
try
 
to
 
start
 
the
 
engine
 
by
 
c

onnecting
 
a
 
battery
 
charger.
Never
 
use
 
a
 
24
 
V
 
or
 
higher
 
battery
 
b

o o s t e r.
First
 
check
 
that
 
the
 
slave
 
battery
 
has
 
a
 
n

ominal
 
voltage
 
of
 
12
 
V
 
and
 
a
 
capacity
 
a

t
 
least
 
equal
 
to
 
that
 
of
 
the
 
discharged
 
b

attery.
The two vehicles must not be in contact
with
 
each
 
other.
Switch off the electrical consumers on
both vehicles (audio system, wipers,
lighting, ...).
Ensure
 
that
 
the
 
jump
 
lead
 
cables
 
do
 n
ot
 
pass
 
close
 
to
 
moving
 
parts
 
of
 
the
 
e

ngine
 
(cooling
 
fan,
 
belts, ...).
Do not disconnect the (+) terminal when
the
 
engine
 
is
 
running.
When
 
your
 
vehicle's
 
battery
 
is
 
discharged,
 
the
 
e

ngine
 
can
 
be
 
started
 
using
 
a
 
slave
 
battery
 
(

external
 
or
 
on
 
another
 
vehicle)
 
and
 
jump
 
lead
 
c

ables
 
or
 
a
 
battery
 
booster.
In the event of a breakdown