2015 SUZUKI NEXA lock

Downloaded from www.Manualslib.com manuals search engine 2-1BEFORE DRIVING
64MS0-74E
Keys
54G489
Your vehicle comes with a pair of identical
keys. Keep the spare key in a safe place.
One key can open all of the locks on the
vehicle.
The key identification number is stamped
on a metal tag provided with the keys or on
the keys. Keep the tag (if equipped) in a
safe place. If you lose your keys, you will
need this number to have new keys made.
Write the number below for your future ref-
erence.
Immobilizer System This system is designed to help prevent
vehicle theft by electronically disabling the
engine starting system.
The engine can be started only with your
vehicle’s original immobilizer ignition key
or keyless push start system remote con-
troller which has an electronic identification
code programmed into it. The key or
remote controller communicates the identi-
fication code to the vehicle when the igni-
tion switch is turned to the “ON” position or
the engine switch is pressed to change the
ignition mode to ON. If you need to make
spare keys or remote controllers, see your
DXWKRULVHG 0DUXWL 6X]XNLZRUNVKRS. The
vehicle must be programmed with the
correctidentification code for the spare.
A keymade by an ordinary locksmith will
not startthe engine.
80JM122
If the immobilizer/keyless push start sys-
tem warning light blinks when the ignition
switch is in the “ON” position or the ignition
mode is ON, the engine will not start.
NOTE:If the immobilizer/keyless push start sys-
tem warning light blinks or comes on, a
message may be shown on the information
display.
If the light still blinks after the ignition
switch is turned back to the “ON” position,
there may be something wrong with your
key or with the immobilizer system. Ask
your DXWKRULVHG 0DUXWL 6X]XNL ZRUNVKRS
tohave the system inspected.
For vehicles with keyless push start
system
If this light blinks, change the ignition mode
to “LOCK” (OFF), then change back to
“ON”. Also refer to “If the master warning
indicator light blinks and the engine cannot
be started” in “Starting the Engine (Vehicle
with Keyless Push Start System)” in the
“OPERATING YOUR VEHICLE” section.
If the light still blinks after the ignition mode
is changed back to “ON”, there may be
something wrong with your key or with the
immobilizer system. Ask yourDXWKRULV
HG 0DUXWL 6X]XNL ZRUNVKRS to have the
systeminspected.
The immobilizer/keyless push start system
warning light may also blinks if the remote
controller is not in the vehicle when you KEY NUMBER:
EXAMPLE
For vehicles without keyless push start
system
If this light blinks, turn the ignition switch to
the “LOCK” position, then turn it back to
the “ON” position.

Downloaded from www.Manualslib.com manuals search engine 2-3BEFORE DRIVING
64MS0-74E
Door LocksSide Door Locks
64MS018
(1) LOCK
(2) UNLOCK
(3) Front
(4) Rear
To lock a front door from outside the vehi-
cle:
• Insert the key and turn the top of the key
toward the rear of the vehicle, or
• Turn the lock knob forward, then pull and
hold the door handle as you close the
door.
To unlock a front door from outside the
vehicle, insert the key and turn the top of
the key toward the front of the vehicle.
64MS019
(1) LOCK
(2) UNLOCK
To lock a door from inside the vehicle, turn
the lock knob forward. Turn the lock knob
rearward to unlock the door.
To lock a rear door from outside the vehi-
cle, turn the lock knob forward and close
the door. You do not need to pull and hold
the door handle as you close the door.
NOTE:
Be sure to hold the door handle when you
close a locked front door, or the door will
not remain locked.
Central Door Locking System
64MS020
(1) LOCK
(2) UNLOCK
(3) Front
(4) Rear
You can lock and unlock all doors (includ-
ing the tailgate) simultaneously by using
the key in the driver’s door lock.
To lock all doors simultaneously, insert the
key in the driver’s door lock and turn the
top of the key toward the rear of the vehi-
cle once.
To unlock all doors simultaneously, insert
the key in the driver’s door lock and turn
the top of the key toward the front of the
vehicle twice.
(1)
(2)
(4)
(3)
(1)
(2)
(4)
(3)
(1)
(2)
Door Lock Knob
EXAMPLE

Downloaded from www.Manualslib.com manuals search engine 2-4
BEFORE DRIVING
64MS0-74E
NOTE:
You can switch the function that unlocks all
doors from twice operations to once opera-
tion, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information Display” in this section.
To unlock the driver’s door only, insert the
key in that door lock and turn the top of the
key toward the front of the vehicle once.
64MS021
(1) LOCK
(2) UNLOCK
You can also lock or unlock all doors by
depressing the front or rear of the switch,
(3) respectively.NOTE:
• You can also lock or unlock all doors by
operating the transmitter or remote con-
troller. Refer to “Keyless Push Start Sys-
tem Remote Controller/Keyless Entry
System Transmitter” in this section.
• If your vehicle is equipped with the key-
less push start system, you can also lock
or unlock all doors by pushing the request
switch. Refer to “Keyless Push Start Sys-
tem Remote Controller/Keyless Entry
System Transmitter” in this section.NOTE:
• All doors are automatically unlocked
when you turn the ignition switch to the
“LOCK” position and pull out the key, or
press the engine switch to change the
ignition mode to LOCK (OFF).
• All doors are automatically locked for
safety when the vehicle speed reaches
15 km/h.
• You can change the automatic locking or
unlocking function mentioned above via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.
Child-Proof Locks (rear door)
61MM0A046
(1)Lock position
(2)Unlock position
Each of the rear doors is equipped with a
child-proof lock which can be used to help
prevent unwanted opening of the door
from inside the vehicle. When the lock
lever is in the lock position (1), the rear
door can only be opened from outside.
When the lock lever is in the unlock posi-
tion (2), the rear door can be opened from
inside or outside.
EXAMPLE
(1)
(2)
(3)
WA R N I N G
Be sure to place the child-proof lock
in the lock position whenever chil-
dren are seated in the rear.


EXAMPLE

Downloaded from www.Manualslib.com manuals search engine 
%()25('5,9,1*
06(
.H\OHVV3XVK6WDUW6\VWHP5HPRWH
&RQWUROOHU7\SH$The remote controller enables the follow-
ing operations:
• You can lock or unlock the doors by
operating the LOCK/UNLOCK buttons
on the remote controller. Refer to the
explanation in this section.
• You can lock or unlock the doors by
pushing the request switch. For details,
refer to the explanation in this section.
• You can start the engine without using
an ignition key. For details, refer to
“Engine Switch” in the

Downloaded from www.Manualslib.com manuals search engine %()25('5,9,1*
06(
NOTE:
• If you lock the doors using the remote
controller when the engine hood is open,
the siren will sound 3 times to remind
you.• If the security system was triggered due
to an unauthorized entry into the vehicle
and then you unlock the doors using the
remote controller, the siren will sound 4
times to remind you. If this happens,
check whether your vehicle has been
broken into while you were away from it.
• Once you push both of the “LOCK” but-
ton (1) and “UNLOCK” button (2), then
you push one of the buttons within 5 sec-
onds, the siren will not sound. However,
If you push one of the buttons twice
within 5 seconds, or push one of the but-
tons 5 seconds later, the siren will sound.
• You can set whether the siren sounds
when locking or unlocking the door(s) via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.NOTE:
• The maximum operating distance of the
remote controller is about 5 m (16 ft.),
but this can vary depending on the sur-
roundings, especially near other trans-
mitting devices such as radio towers or
CB (Citizen’s Band) radios.
• The door locks cannot be operated with
the remote controller if the ignition mode
is other than the LOCK (OFF).
• When any door is open, if you push the
“LOCK” button on the remote controller,the exterior buzzer will sound and doors
cannot be locked.
•
If you lose one of the remote controllers,
ask your DXWKRULVHG 0DUXWL 6X]XNL
ZRUNVKRSas soon as possible for a
replacement.Be sure to have your
dealer program thenew remote
controller code in your vehi-cle’s
memory so that the old code is
erased.3DQLFDODUPIXQFWLRQ
This function is to get the attention of oth-
ers.
Push both of the “LOCK” button (1) and
“UNLOCK” button (2) for more than 3 sec-
onds. The turn signal lights will blink for
about 27.5 seconds. Also, the siren will
sound for about 27.5 seconds at the same
time.
To cancel the panic alarm, press any but-
ton (LOCK OR UNLOCK). You can also
change the ignition mode to ON to cancel
the panic alarm.
NOTE:
The panic alarm function will not activate
when the ignition mode is “ACC” or “ON”.

Downloaded from www.Manualslib.com manuals search engine 
%()25('5,9,1*
06(
.H\OHVV XQORFNLQJORFNLQJ XVLQJ WKH
UHTXHVWVZLWFKHV
64MS134
When the remote controller is within the
operating range described in this section,
you can lock or unlock the doors (including
the tailgate) by pushing the request switch
(1) on the driver’s door handle, front pas-
senger’s door handle or tailgate.
To lock all doors when all doors are
unlocked:
• To lock all doors, push one of the
request switches once.
The turn signal lights will flash once and
the siren will sound once when the doors
are locked.
To unlock a door or all doors:
• Push one of the request switches once
to unlock only one door.
• Push one of the request switches twice
to unlock all doors.NOTE:
You can switch the function that unlocks all
doors from twice operations to once opera-
tion, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information Display” in this section.
When the doors are unlocked:
• The turn signal lights will flash twice and
the siren will sound twice.
• If the interior light switch is in the door
position, the interior light will turn on for
about 15 seconds and then fade out. If
you press the engine switch during this
time, the light will start to fade out imme-
diately.
Be sure the doors are locked after you
operate the request switch to lock the
doors.NOTE:
• If you lock the doors using the request
switch when the engine hood is open,
the siren will sound 3 times to remind
you.
• If the security system was triggered due
to an unauthorized entry into the vehicle
and then you unlock the doors using the
request switch, the siren will sound 4
times to remind you. If this happens,
check whether your vehicle has been
broken into while you were away from it.
• You can set whether the siren sounds
when locking or unlocking the door(s) via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.NOTE:• The door locks cannot be operated by
the request switch under the following
conditions:
– If any door is open or is not completely
closed.
– If the ignition mode is other than LOCK
(OFF).
• If no doors are opened within about 30
seconds after unlocking the doors by
pushing the request switch, the doors will
be locked again automatically.
(1)
(;$03/(
NOTICE

Downloaded from www.Manualslib.com manuals search engine %()25('5,9,1*
06(
80J056
(1) 80 cm (2 1/2 feet)
When the remote controller is within
approximately 80 cm (2 1/2 feet) from a
front door handle or the tailgate switch, you
can lock or unlock the doors by pushing
the request switch.
NOTE:
• If the remote controller is outside the
request switch operating range
described above, you will not be able to
operate the request switch.
• If the battery of the remote controller
runs down or there are strong radio
waves or noise, the request switch oper-
ating range may be reduced or the
remote controller may be inoperative.
• If the remote controller is too close to the
door glass, the request switches may not
operate.• If a spare remote controller is in the vehi-
cle, the request switches may not oper-
ate normally.
• The remote controller will only operate a
request switch if it is within the switch’s
operating range. For example, if the
remote controller is within the operating
range of the driver’s door request switch
but not the front passenger’s door
request switch or the tailgate request
switch, the driver’s door switch can be
operated but the front passenger’s door
switch or tailgate switch cannot be oper-
ated.
• Avoid operations of switch with sharp
objects.
NOTE:
The keyless push start system may not
function correctly in certain environments
or under certain operating conditions such
as the following:• When there are strong signals coming
from a television, power station or a cel-
lular phone.
• When the remote controller is in contact
with or covered by a metal object.
• When a radio wave type remote keyless
entry is used nearby.
• When the remote controller is placed
near an electronic device such as per-
sonal computer.
Some additional precautions you should
take and information you should be aware
of are:
• Make sure the key is stowed in the
remote controller. If the remote controller
becomes unreliable, you will not be able
to lock or unlock the doors.
• Be sure that the driver always carries the
remote controller.
•If you lose one of the remote controllers,

ask your
DXWKRULVHG 0DUXWL 6X]XNL
ZRUNVKRSas soon as possible for a
replacement.Be sure to have your
dealer program the

new remote
controller code in your vehi-cle’s
memory so that the old code is

erased.
• You can use up to four remote controllers

and the keys for your vehicle. Ask your

DXWKRULVHG 0DUXWL 6X]XNL ZRUNVKRS
for

details.
• The battery life of the remote controller is
about two years, but it can vary depend-
ing on usage conditions.
(1)
(1)(1)
(;$03/(
NOTICE
7KH UHPRWH FRQWUROOHU LV D VHQVLWLYH
HOHFWURQLF LQVWUXPHQW 7R DYRLG GDP
DJLQJWKHUHPRWHFRQWUROOHU

Downloaded from www.Manualslib.com manuals search engine 
%()25('5,9,1*
06(
57L21016
To stow the key into the remote controller,
push the key in the remote controller until
you hear a click.
68LM247
To remove the key from the remote control-
ler, push the button (A) in the direction of
the arrow and pull the key out from the
remote controller.5HTXHVWVZLWFKZDUQLQJEX]]HU
This exterior buzzer beeps for about 2 sec-
onds in the following conditions to warn you
that the request switch is not working:
• The request switch is pressed after all
doors are closed with the ignition mode
changed to “ACC” or “ON” by pressing
the engine switch.
• The request switch is pressed in any of
the following conditions after changing
the ignition mode to “LOCK” (OFF) by
pressing the engine switch.
– The remote controller is left inside the
vehicle.
– Any door (including the tailgate) is
open.
Press the request switch again after doing
the following:
With the ignition mode changed to “LOCK”
(OFF) by pressing the engine switch, bring
out the remote controller if it is inside the
vehicle and check that all doors are com-
pletely closed.
5HPLQGHUIXQFWLRQ
64MS165
If the remote controller is not in the vehicle
under the following conditions, the buzzer
sounds intermittently for about 2 seconds
and the immobilizer/keyless push start sys-
tem warning light on the instrument cluster
blinks:When one or more doors are opened and
all of the doors are later closed with the
ignition mode is other than “LOCK”.
The indicator light will turn off within sev-
eral seconds after the remote controller is
returned to an area of the vehicle other
than the rear luggage area.
If the remote controller is left in the vehicle
and you lock the driver’s door or front pas-
senger’s door as described below, the door
will be automatically unlocked.
• If you open the driver’s door and lock the
door by turning the lock knob forward or
pushing the power door locking switch,
(A)
(;$03/(