2015 SUZUKI NEXA parking brake
[x] Cancel search: parking brakePage 80 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
: D U Q L Q J D Q G , Q G L F D W R U / L J K W VNOTE:
If warning and indicator lights blink or
come on, the corresponding messages
may be shown on the information display.
% U D N H 6 \ V W H P : D U Q L Q J / L J K W
65D477
Three different types of operations exist
depending on the vehicle’s specification.
1) The light comes on briefly when the
ignition switch is turned to the “ON”
position or the engine switch is pressed
to change the ignition mode to “ON”.
2) The light comes on when the parking
brake is engaged with the ignition
switch in the “ON” position or the igni-
tion mode “ON”.
3) The light comes on when under either
or both of above two conditions.
The light also comes on when the fluid in
the brake fluid reservoir falls below the
specified level.
The light should go out after starting the
engine and fully releasing the parking
brake, if the fluid level in the brake fluid
reservoir is adequate.
If your vehicle is equipped with the ABS,
the brake system warning light also comes
on together with the ABS warning light
when the rear brake force control function(proportioning valve function) of the ABS
system fails.
If the brake system warning light comes on
while you are driving the vehicle, it may
mean that there is something wrong with
the vehicle’s brake system. If this happens,
you should:
1) Pull off the road and stop carefully.
2) Test the brakes by carefully starting and
stopping on the shoulder of the road.
3)If you determine that it is safe, drive
cautiously at low speed to the nearest
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S for
repairs, or
4) Have the vehicle towed to the nearest
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S for
repairs.
: $ 5 1 , 1 *
5 H P H P E H U W K D W V W R S S L Q J G L V W D Q F H
P D \ E H O R Q J H U \ R X P D \ K D Y H W R S X V K
K D U G H U R Q W K H S H G D O D Q G W K H S H G D O
P D \ J R G R Z Q I D U W K H U W K D Q Q R U P D O
Page 81 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
NOTE:
Because the brake system is self-adjust-
ing, the fluid level will drop as the brake
pads become worn. Replenishing the
brake fluid reservoir is considered normal
periodic maintenance.
NOTE:
(Parking Brake Reminder Buzzer)
A buzzer sounds intermittently to remind
you to release the parking brake if you
start the vehicle without releasing the park-
ing brake. Make sure that the parking
brake is fully released and the brake sys-
tem warning light turns off.
$ Q W L / R F N % U D N H 6 \ V W H P $ % 6
: D U Q L Q J / L J K W L I H T X L S S H G
65D529
When the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
“ON”, the light comes on briefly so you can
check that the light is working.
If the light stays on, or comes on when
driving, there may be something wrong
with the ABS.
If this happens:
1) Pull off the road and stop carefully.
2) Turn the ignition switch to “LOCK” or
change the ignition mode to “LOCK”
(OFF) by pressing the engine switch
and then start the engine again.
If the warning light comes on briefly then
turns off, the system is normal. If the warn-
ing light still stays on.
If the light and the brake system warning
light stay on, or come on simultaneously
when driving, your ABS system is
equipped with the rear brake force control
function (proportioning valve function) andthere may be something wrong with both
the rear brake force control function and
anti-lock function of the ABS system.
If one of these happens, have the system
inspected by your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S
If the ABS becomes inoperative, the brake
system will function as an ordinary brake
system that does not have this ABS sys-
tem.
For details of ABS system, refer to “Anti-
Lock Brake System (ABS)” in the “OPER-
ATING YOUR VEHICLE” section.
: $ 5 1 , 1 *
, I D Q \ R I W K H I R O O R Z L Q J F R Q G L W L R Q V
R F F X U \ R X V K R X O G L P P H G L D W H O \ D V N
\ R X U D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N
V K R S W R L Q V S H F W W K H E U D N H V \ V W H P
G R H V Q R W J R R X W D I W H U W K H H Q J L Q H
K D V E H H Q V W D U W H G D Q G W K H S D U N L Q J
E U D N H K D V E H H Q I X O O \ U H O H D V H G
Page 101 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
4) Make sure the hood is fully closed and
latched.
5) Check the headlights, turn signal lights,
brake lights and horn for proper opera-
tion.
6) Adjust the seat and head restraint.
7) Check the brake pedal and the parking
brake lever.
8) Adjust the mirrors.
9) Make sure that you and all passengers
have properly fastened the seat belts.
10)Make sure that all warning lights come
on as the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
ON.
11)Check all gauges.
12)Make sure that the BRAKE SYSTEM
WARNING light turns off when the park-
ing brake is released.
Once a week, or each time you fill your fuel
tank, perform the following under-hood
checks:
1) Engine oil level
2) Coolant level
3) Brake fluid level
4) Battery electrolyte level
5) Windshield washer fluid level
6) Hood latch operation
Pull the hood release handle inside the
vehicle. Make sure that you cannot
open the hood all the way without
releasing the secondary latch. Be sure
to close the hood securely after check-
ing for proper latch operation. See theitem “All latches, hinges and locks” of
Page 108 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
– The remote controller is in stowage
like the glove box or a door pocket.
– The remote controller is in the sun
visor pocket or on the floor.
• Even when the remote controller is out-
side the “interior workable” area, if it is in
any of the following conditions, you may
be able to start the engine or select the
ignition mode. The “remote controller
outside” warning may not be given at
that time.
– The remote controller is outside the
vehicle but very close to a door.
– The remote controller is on the instru-
ment panel.
3 D U N L Q J % U D N H / H Y H U
64MS185
(1) To set
(2) To release
(3) To release
The parking brake lever is located between
the seats. To set the parking brake, hold
the brake pedal down and pull the parking
brake lever all the way up. To release the
parking brake, hold the brake pedal down,
pull up slightly on the parking brake lever,
push the button on the end of the lever
with your thumb, and lower the lever to its
original position.
(2)
(3) (1)
( ; $ 0 3 / (
: $ 5 1 , 1 *
Page 109 of 288
![SUZUKI NEXA 2015 1.G Owners Manual Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
3 D U N L Q J % U D N H 5 H P L Q G H U % X ] ] H UA buzzer sou](/manual-img/20/7598/w960_7598-108.png "SUZUKI NEXA 2015 1.G Owners Manual Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
3 D U N L Q J % U D N H 5 H P L Q G H U % X ] ] H UA buzzer sou")
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
3 D U N L Q J % U D N H 5 H P L Q G H U % X ] ] H UA buzzer sounds intermittently to remind
you to release the parking brake if you start
the vehicle without releasing the parking
brake. Make sure that the parking brake is
fully released and the brake system warning
light turns off.
3 H G D O
80J2121
& O X W F K 3 H G D O The clutch pedal is used to disengage the
drive to the wheels when starting the
engine, stopping, or shifting the gearshift
lever. Depressing the pedal disengages the
clutch. % U D N H 3 H G D O Your vehicle is equipped with either front
and rear disc brakes or front disc brakes
and rear drum brakes. Depressing the
brake pedal applies both sets of brakes.
You may hear occasional brake squeal
when you apply the brakes. This is a nor-mal condition caused by environmental
factors such as cold, wet, snow, etc.
$ F F H O H U D W R U 3 H G D O This pedal controls the speed of the
engine. Depressing the accelerator pedal
increases power output and speed.
: $ 5 1 , 1 *
' R Q R W G U L Y H Z L W K \ R X U I R R W U H V W L Q J R Q
W K H F O X W F K S H G D O , W F R X O G U H V X O W L Q
H [ F H V V L Y H F O X W F K Z H D U F O X W F K G D P D J H
R U X Q H [ S H F W H G O R V V R I H Q J L Q H E U D N L Q J
(2)
(1)
(3) ( ; $ 0 3 / (
: $ 5 1 , 1 *
, I E U D N H V T X H D O L V H [ F H V V L Y H D Q G
R F F X U V H D F K W L P H W K H E U D N H V D U H
D S S O L H G \ R X V K R X O G K D Y H W K H E U D N H V
F K H F N H G E \ \ R X U D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S
: $ 5 1 , 1 *
' R Q R W U L G H W K H E U D N H V E \ D S S O \ L Q J
W K H P F R Q W L Q X R X V O \ R U U H V W L Q J \ R X U
I R R W R Q W K H S H G D O 7 K L V Z L O O U H V X O W L Q
R Y H U K H D W L Q J R I W K H E U D N H V Z K L F K
F R X O G F D X V H X Q S U H G L F W D E O H E U D N L Q J
D F W L R Q O R Q J H U V W R S S L Q J G L V W D Q F H V R U
S H U P D Q H Q W E U D N H G D P D J H
Page 110 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 ( 6 W D U W L Q J W K H ( Q J L Q H
9 H K L F O H Z L W K R X W . H \ O H V V 3 X V K
6 W D U W 6 \ V W H P
% H I R U H 6 W D U W L Q J W K H ( Q J L Q H
64MS146
1) Make sure the parking brake is set fully.
2) Shift into “N” (Neutral) and depress the
clutch pedal all the way to the floor. Hold
the clutch pedal while starting the
engine.
6 W D U W L Q J D & R O G D Q G : D U P ( Q J L Q H & R O G H Q J L Q H
Turn the ignition switch to the “ON” posi-
tion and wait until the glow plug indicator
goes out if it comes on. Crank the engine
by turning the ignition key to “START”.
Release the key when the engine starts.
: D U P H Q J L Q H
Crank the engine by turning the ignition
key to “START”. Release the key when the
engine starts.
& D X W L R Q Z K H Q V W R S S L Q J W K H H Q J L Q H Z L W K
W X U E R F K D U J H U
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.
5 H V W D U W L Q J G L H V H O H Q J L Q H D I W H U I X H O
H P S W \ V W R S
If the engine stops and the low fuel warning
light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Hold the ignition key in “ON” position for
5-10 seconds to feed fuel.
3) Perform above engine starting proce-
dure to start the engine.
If the malfunction indicator light still comes
on after the engine started, there may be
some problem with the engine. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
to have
the
engine inspected.
: $ 5 1 , 1 *
Page 111 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 ( 6 W D U W L Q J W K H ( Q J L Q H
9 H K L F O H Z L W K . H \ O H V V 3 X V K 6 W D U W
6 \ V W H P
% H I R U H 6 W D U W L Q J W K H ( Q J L Q H
64MS169
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
82K254
3) The “PUSH START SWITCH” message
will appear on the information display in
the instrument cluster. Push the engine
switch (1). When the engine is started,
the starter motor will automatically stop.
NOTE:
• You do not need to keep the engine
switch pressed to start the engine.
• The engine of a manual transaxle vehi-
cle will not start unless the clutch pedal
is depressed.
• During the engine starting procedure,
messages on the information display will
help you. Refer to “Information Display”in the “BEFORE DRIVING” section for
details.
• You should turn off such loads as the
headlights and air conditioning system to
facilitate starting of the engine.
• Even if you fail to start the engine, the
starter motor will stop operating auto-
matically after a short time. After the
starter motor has stopped or if there is
some problem with the system, the
starter motor will rotate only while the
engine switch is being pressed.
6 W R S S L Q J W K H H Q J L Q H• Depress the engine switch to stop the
engine after the vehicle stopped com-
pletely.
• In case of emergency, you can stop the
engine by quickly pushing the engine
switch more than 3 times, or pushing
and holding the engine switch more than
2 seconds while the vehicle in motion.
NOTE:
Except in emergency, do not stop the
engine while the vehicle in motion.
The steering and braking operation will
require more efforts when the engine
stopped.
Refer to “Braking” in this section.
• If the engine has been stopped and
stayed as it as for while after the engine
was stopped unexpectedly or was raced
before stopped, a clicking sound may be
heard from around the engine when
engine restarted. This is not a malfunc-
(1)
: $ 5 1 , 1 *
0 D N H V X U H W K D W W K H S D U N L Q J E U D N H L V
V H W I X O O \ D Q G W K H W U D Q V D [ O H L V L Q 1 H X
W U D O E H I R U H D W W H P S W L Q J W R V W D U W W K H
H Q J L Q H
NOTICE
Page 112 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
tion. In this case, always let the engine
idle before stop it. 6 W D U W L Q J D & R O G D Q G : D U P ( Q J L Q H & R O G H Q J L Q H
Depress the clutch and brake pedals fully
and press the engine switch to crank the
engine. If the glow plug indicator light
comes on, the engine will start automati-
cally after the glow plug indicator light goes
off or 10 seconds past.
: D U P H Q J L Q H
Crank the engine by pressing the engine
switch to change the ignition mode to
“START”. & D X W L R Q Z K H Q V W R S S L Q J W K H H Q J L Q H Z L W K
W X U E R F K D U J H U
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.
5 H V W D U W L Q J G L H V H O H Q J L Q H D I W H U I X H O
H P S W \ V W R S
If the engine stops and the low fuel warn-
ing light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Press the engine switch to change the
ignition mode to “ON” for 5-10 seconds
to feed fuel.
3) Perform above engine starting proce-
dure to start the engine.
If the malfunction indicator light still comes
on after the engine started, there may be
some problem with the engine. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S to have
the engine inspected.
, I W K H 0 $ 6 7 ( 5 : $ 5 1 , 1 * L Q G L F D W R U O L J K W
E O L Q N V D Q G W K H H Q J L Q H F D Q Q R W E H V W D U W H G
Your keyless push start system remote
controller may not be sensed as being
within the interior workable area. Try again
after making sure that you have the remote
controller with you. If the engine still can-
not be started, the battery of the remote
controller may be discharged. You mustthen use the following method to be able to
start the engine.
58MST0302
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
3) The “PUSH START SWITCH.” mes-
sage will appear on the information dis-
play in the instrument cluster. Press the
engine switch (1).
4) Within about 10 seconds of blinking of
the “MASTER WARNING” indicator
light in the instrument cluster, touch the
engine switch with the lock button end
of the remote controller (2) for about 2
seconds.
NOTE:
• If you still cannot start the engine after
several attempts using the above
NOTICE
' R Q R W F U D Q N W K H H Q J L Q H I R U P R U H
W K D Q V H F R Q G V D W D W L P H
, I W K H H Q J L Q H G R H V Q