2015 Peugeot RCZ light

19
RCZ_en_Chap01_controle-de-marche_ed01-2015
Warning/indicator lamp is on CauseAction / Observations
Rear foglamp fixed.The rear foglamp has been
switched on using the ring on the
lighting control stalk. Turn the ring on the lighting control stalk to the rear to
switch off the rear foglamp.
d

iesel engine
pre-heating fixed.The key is at position 2
(ignition on) in the ignition switch. Wait until the warning lamp goes off before starting.
The period of illumination of the warning lamp is
determined by the ambient conditions (up to about thirty
seconds in very low temperatures).
If the engine does not start, switch the ignition off and then
on, wait until the warning lamp goes off again, then start
the engine.
Parking brake fixed.The parking brake is applied or
not properly released. Release the parking brake to switch off the warning lamp,
keeping your foot on the brake pedal.
Observe the safety recommendations.
For more information on the parking brake, refer to the
corresponding section.
Passenger's
front airbag fixed
on the
seat belt and
passenger's front
airbag warning
lamps display

.The control switch, located on
the passenger's side of the
dashboard, has been placed in
the "ON" position.
The passenger's front airbag is
activated.
In this case, do not install
a
"rearward facing" child seat. While
you do not have a rearward facing child seat fitted
to the front passenger seat, it is recommended that the
passenger's front airbag be activated.
On

the other hand, before fitting a rearward facing child
seat, you must turn the control switch to the

"OFF"
position.
1/
MONITORING

26
RCZ_en_Chap01_controle-de-marche_ed01-2015
LIGHTING dIMMER
Permits manual adjustment of the brightness of the instruments and
controls to suit the ambient light level. Only operates when the vehicle\

lighting is on, with the exception of the daytime running lamps.
Activation
F Press the button to change the brightness of the instruments and
controls.
F

When the lighting reaches the minimum setting, release the button,
then press again to increase it.
or
F


When the lighting reaches the maximum setting, release the button,
then press again to reduce it.
F

When the lighting reaches the level of brightness required, release
the button.
deactivation
When the vehicle lighting is off, or in day mode on vehicles fitted with daytime running lamps, pressing the button does not have any effect.
CLOCK
The analogue clock, located between the central vents of the
dashboard, does not have an adjustment button.
To set the time, refer to the section relating to your multifunction
screen's
configuration menu.
The clock is synchronised with the multifunction screen time; once the
the
setting has been confirmed on the multifunction screen, the hands
will turn to synchronise with the screen, and each time the ignition is \
switched on.

32
RCZ_en_Chap01_controle-de-marche_ed01-2015
* Depending on version.
** Depending on country of sale.
"PERSONALISATION-CONFIGURATION"
MENU
Once this menu has been selected, you can gain access to the
following functions:
- define the vehicle parameters,
- display
configuration,
-

choice of language.
define the vehicle parameters*
Once this menu has been selected, you can activate or deactivate the
following equipment:
-

selective unlocking (refer to the "Access" section),
-


guide-me-home lighting (refer to the "V
isibility" section),
-
interior mood lighting (refer to the "Ease of use and comfort" section)\
,
-


daytime running lamps** (refer to the "V
isibility" section),
-

rear parking sensors (refer to the "Driving" section). Example: setting of the duration of the guide-me-home lighting
F


Press the "
5" or "6" buttons, then the "OK" button to select the
menu required.
F
Press the "
5" or "6" buttons, then the "OK" button to select the
"Guide-me-home headlamps" line.
F
Press the "
7" or "8" buttons to set the value required (15, 30 or

60 seconds), then press the "OK"
button to confirm.
F Press the " 5" or "6" buttons, then the "OK" button to select the
"OK"
box and confirm or press the
"Back" button to cancel.

35
RCZ_en_Chap01_controle-de-marche_ed01-2015
"SETUP" MENU
F Press the "SETUP" button to gain access to the configuration menu:
- "Display configuration",
-

"V
oice synthesis",
-

"Choice of language",
-


"V
ehicle parameters",
-

"Alert log".
As

a safety measure, configuration of the multifunction screen by
the driver must only be done when stationary

.
display configuration
This menu allows you to choose a colour scheme for the screen, to
adjust the brightness, set the date and time and choose the units for
distance (km or miles), fuel consumption (l/100 km, mpg or km/l) and\

temperature (°Centigrade or °Fahrenheit).
Voice synthesis
This men allows you to adjust the volume for navigation instructions and\

to choose the type of voice (male or female).
* Depending on version.
** According to country of sale.
Choice of language
This menu allows you to choose the language used by the screen
(French, English, Italian, Portuguese, Spanish, German, Dutch, Turkish,
Polish, Russian).
Vehicle parameters*
This menu allows you to activate or deactivate certain driving and
comfort equipment, arranged by category:
-

Access to the vehicle
●

Plip action (selective unlocking of the driver's door; refer to the
"Access" section),
-


Parking sensors
-

Lighting configuration (see the "Visibility" section) :
● Duration
of the guide-me-home lighting,
● Directional
headlamps (main/additional directional lighting),
● Mood
lighting (Interior mood lighting),
● Daytime
running lamps**.
Alert log
It lists the active alerts by displaying their associated messages in tu\
rn.
Setting the date and time
F
Press "
SETUP".
F Select

"Display

configuration"

and

confirm.
F Select

"Set

date

and

time"

and

confirm.
You can select "Synchronise the minutes with GPS ", so that the
minutes are adjusted automatically by satellite reception. F Select
the setting to modify. Confirm by pressing "
OK", then adjust
the setting and modify again.
F
Adjust the settings one by one.
F

Select "
OK" in the screen then confirm to save the setting.
1/
MONITORING

37
RCZ_en_Chap02_ouvertures_ed01-2015
REMOTE CONTROL KEY
System which permits central unlocking or locking of the vehicle using
the lock or from a distance. It is also used to locate and start the
vehicle, as well as providing protection against theft.
UNLOCKING THE VEHICLE
Unfolding the key
F First press this button to unfold the key .
Complete unlocking using the remote control
F Press the open padlock to unlock the vehicle.
Selective unlocking using the remote control
F Press the open padlock once to unlock the driver's door
and
the fuel filler flap only.
F

Press the open padlock again to unlock the passenger's door and
the boot.
Selective unlocking using the key
F Turn the key forwards in the driver's door lock once to unlock the driver's door and the fuel filler flap only.
F

T
urn the key forwards in the driver's door lock again to unlock the
passenger's door and the boot.
The complete or selective unlocking parameter is set via
the
vehicle configuration menu.
Complete unlocking is activated by default.
Complete unlocking using the key
F Turn the key forwards in the driver's door lock to unlock the vehicle.
Unlocking and partial opening of the boot
F Press this button for more than two seconds to unlock
the boot. The boot opens slightly.
This
action also unlocks the doors and the fuel filler flap.
The

direction indicators flash for a few seconds.
Depending on version, the door mirrors unfold, the alarm is deactivated.\
2/
ACCESS

39
RCZ_en_Chap02_ouvertures_ed01-2015
Folding the key
F First press this button to fold the key.
LOCATING YOUR VEHICLE
R

EMOTE
CONTROL
PROBLEM
Following disconnection of the vehicle battery, replacement of the
remote control battery or in the event of a remote control malfunction, \
you can no longer unlock, lock or locate your vehicle.
F
First of all, use the key in the lock to unlock or lock your vehicle.
F


Then, reinitialise the remote control.
If the problem persists, contact a PEUGEOT

dealer as soon as
possible.
Reinitialisation
F Switch of f the ignition.
F
T
urn the key to position 2 (Ignition on) .
F

Press the closed padlock immediately for a few seconds.
F


Switch of
f the ignition and remove the key from the ignition switch.
The remote control is fully operational again.
Changing the battery
Battery ref.: CR1620 / 3 volts.
If the battery is flat, you are informed by illumination of this
warning lamp, accompanied by an audible signal and an alert
message in the screen.
F


Unclip the casing using a coin at the notch.
F

Slide the flat battery out of its location.
F

Slide the new battery into its location observing the original
direction.
F


Clip the casing.
F


Reinitialise the remote control.
This function allows you to identify your vehicle from a
distance, particularly in poor light.

Your vehicle must be
locked.
F
Press the closed padlock on the remote control.
This will switch on the courtesy lamps and the direction indicators will\

flash

for

around

ten

seconds.
If you do not press the button when folding the key, there is a risk
of damage to the mechanism.
2/
ACCESS

49
RCZ_en_Chap02_ouvertures_ed01-2015
BOOT
OPENING
F Press this button for more than two seconds to unlock
the boot lid. The boot lid opens slightly.
F

Lift the boot lid.
This


action
also unlocks the doors and the fuel filler flap.
Using the manual control; vehicle unlocked
F Press the opening control above the number plate.
F
Lift the boot lid.
CLOSING
F Lower the boot lid using one of the interior grab handles.
F
If necessary
, press the top of the boot lid to close it fully.
If the boot lid is not closed correctly: -

when the engine is running
, this warning lamp comes on,
accompanied by a message in the screen for a few seconds,
When selective unlocking is activated, the boot can also be
opened by a second press on the open padlock on the remote
control.
Using the remote control
Emergency locking
If the central locking system fails (flat battery), you are advised to disconnect the battery.
-

when the vehicle is moving
(speed above 6 mph (10 km/h)), this
warning lamp comes on, accompanied by an audible signal and a
message in the screen for a few seconds.
Never grasp the boot lid by the active spoiler
.
2/
ACCESS

57
RCZ_en_Chap03_confort_ed01-2015
REAR VIEW MIRROR
Adjustable mirror providing a central rearward view.
Equipped with an anti-dazzle system, which darkens the mirror glass
and reduces the nuisance to the driver caused by the sun, headlamps
from other vehicles...
Automatic day/night model
In order to ensure optimum visibility during your manoeuvres,
the mirror lightens automatically when reverse gear is engaged.
By means of a sensor, which measures the light from the rear of the
vehicle, this system automatically and progressively changes between
the day and night uses. Due to the curve of the rear screen, the image in the rear view
mirror may be slightly distorted; take this into account when
manoeuvring the vehicle.
3/
EASE OF USE and COMFORT