2015 MITSUBISHI ASX Owner's Manual (in English)

8-Side turn-signal lamps (on outside rear-
view mirror) *1*1
:if so equipped*2:Have the lamps bulbs replaced at a
MITSUBISHI MOTORS Author-
ized Service Point.
Codes in parentheses indicate bulb types.
WARNINGl Always consult a specialist when repair-
ing or replacing the bulbs of high intensi- ty discharge headlamps.
This is because the power circuit, bulbs
and electrodes generate a high voltage
that could cause an electric shock.NOTEl An LED, not a bulb, is used in the side turn-
signal lamp (on outside rear-view mirror,
daytime running lamp (type 2), and position lamp (type 2)).
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.NOTEl For the side turn-signal lamp (on fender), it
is not possible to repair or replace just the
bulb.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
9- High-mounted stop lamp
10- Licence plate lamps: 5 W (W5W)
11- Rear fog lamp: 21 W (W21W)
12- Reversing lamps: 16 W (W16W)
13- Rear turn-signal lamps: 21 W (W21W) 14- Stop and tail lamps
Codes in parentheses indicate bulb types.
NOTEl An LED, not a bulb, is used in the stop
lamp/tail lamp and high-mounted stop lamp.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.Inside
E01003402094
1- Room lamp (rear)*: 8 W
2- Vanity mirror lamps*: 2 W or 3 W
3- Room lamp (front) & map lamps: 8 W
4- Luggage room lamp: 5 W
5- Glove box lamp: 1.4 W
*: if so equipped
Replacement of lamp bulbs
10-27OGAE15E5Maintenance10 Rear

Headlamps (low beam, exceptfor vehicles with high intensity discharge headlamps)
E01009301522
1. When replacing the bulb on the left side
of the vehicle in the case of diesel-pow- ered vehicles, remove the bolt (A) hold-
ing down the relay box and move the re- lay box towards the rear of the vehicle.
*: Front of the vehicle
2. When replacing the bulb on the right
side of the vehicle in the case of diesel-
powered vehicles (1600 models only), remove the bolts (B), and then move thereserve tank.
*: Front of the vehicle
3. When replacing the bulb on the right
side of the vehicle in the case of diesel-
powered vehicles, remove the clips (C)
by prying with a straight blade (or mi- nus) screwdriver, and remove the side
cover.
*: Front of the vehicle
4. Turn the cap (D) anticlockwise to re-
move it.
*: Front of the vehicle
5. Turn the bulb (E) anticlockwise to re-
move it.
*: Front of the vehicle
Replacement of lamp bulbs
10-28OGAE15E5Maintenance10

6.While holding down the tab (F), pull out
the socket (G).
7. To install the bulb, perform the removal
steps in reverse.
CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres- surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the headlamps are op-
erated.
If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., and
refit it after drying it thoroughly.Headlamps (low beam, for ve-
hicles with high intensity dis- charge headlamps)
E01010100132
Do not attempt to disassemble or repair head- lamps, and do not attempt to replace their
bulbs.
WARNINGl A high voltage is present in the power cir-
cuit and in the bulbs and bulb terminals. To avoid the risk of an electric shock, con- tact a MITSUBISHI MOTORS Author-
ized Service Point whenever repair or re- placement is necessary.Headlamps (High-beam)
E01009400135
1. When replacing the bulb on the left side
of the vehicle in the case of diesel-pow-
ered vehicles, remove the bolt (A) hold-
ing down the relay box and move the re- lay box towards the rear of the vehicle.
*: Front of the vehicle
Replacement of lamp bulbs
10-29OGAE15E5Maintenance10

2.Turn the cap (B) anticlockwise to re-
move it.
*: Front of the vehicle
3. Turn the bulb (C) anticlockwise to re-
move it.
*: Front of the vehicle
4. While holding down the tab (D), pull out
the socket (E).
5. To install the bulb, perform the removal
steps in reverse.
CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres- surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the headlamps are op-
erated.
If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., and
refit it after drying it thoroughly.Position lamps (type 1)*
E01003702316
1. When replacing the bulb on the left side
of the vehicle in the case of diesel-pow-
ered vehicles, remove the bolt (A) hold-
ing down the relay box and move the re- lay box towards the rear of the vehicle.
*: Front of the vehicle
Replacement of lamp bulbs
10-30OGAE15E5Maintenance10

2.When replacing the bulb on the right
side of the vehicle in the case of diesel-
powered vehicles, remove the clips (B)
by prying with a straight blade (or mi- nus) screwdriver, and remove the side
cover.
*: Front of the vehicle
3. Turn the socket (C) anticlockwise to re-
move it.
*: Front of the vehicle
4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps
E01003800922
To remove 1. Remove the upper cover. For information regarding how to re-move the upper cover, refer to “Remov-
ing and installing the upper cover and duct” on page 10-10.
2. Remove the entire socket and bulb as-
sembly (A) by turning it anticlockwise.
*: Front of the vehicle
3. Remove the bulb by pulling it out.
To install 1. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-31OGAE15E5Maintenance10

2. Install the upper cover.For information regarding how to install
the upper cover, refer to “Removing and
installing the upper cover and duct” on page 10-10.Side turn-signal lamps (on
fender)*
E01003900516
NOTEl For the side turn-signal lamps (on fender), it
is not possible to repair or replace just thebulb.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.Side turn-signal lamps (on out-
side rear-view mirror)*
E01003900529
NOTEl An LED, not a bulb, is used in the side turn-
signal lamps (on outside rear-view mirror).
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.Front fog lamps*
E01004002941
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip into the
fog lamp cover (A) and pry gently to re- move it.
2. Remove the screws (B), and remove the
lamp unit.
NOTEl Except for vehicles equipped with daytime
running lamps, when unfastening the screws,be careful not to move the beam position ad-
justment screw (C).
Replacement of lamp bulbs
10-32OGAE15E5Maintenance10 Type 1 Type 2

3.While holding down the tab (D), pull out
the socket (E).
4. Turn the bulb (F) anticlockwise to re-
move it.
5. To install the bulb, perform the removal
steps in reverse.
CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres-
surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the fog lamps are op- erated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc., and refit it after drying it thoroughly.Daytime running lamps (type
2)*/Position lamps (type 2)*
E01012000021
NOTEl An LED, not a bulb, is used in the daytime
running lamp (type 2) / position lamp (type
2). Contact a MITSUBISHI MOTORS Au-
thorized Service Point when there is a need for repair or replacement.Daytime running lamps (type
1)*
E01011201137
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip into the
daytime running lamp cover (A) and pry gently to remove it.
Replacement of lamp bulbs
10-33OGAE15E5Maintenance10

2.Remove the screws (B), and then re-
move the lamp unit.
3. Turn the bulb (C) anticlockwise to re-
move it.
4. While holding down the tab (D), pull out
the socket (E).
5. To install the bulb, perform the removal
steps in reverse.
Rear fog lamp
E01004101596
1. When removing the lamp unit (A), push
it towards the left side of the vehicle body.
2. Remove the socket (B) and bulb assem-
bly by turning it anticlockwise.
3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-34OGAE15E5Maintenance10