2015 Citroen C4 Owner's Manual

255
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Fuse N°Rating Functions
F19 30 AWindscreen
  wipers   slow   /   fast   speed.
F20 15 AFront
  and   rear   screenwash   pump.
F21 20 AHeadlamp
  wash   pump.
F22 15 AHorn.
F23 15 ARight-hand
  main   beam   headlamp.
F24 15 ALeft-hand
  main   beam   headlamp.
F27 5 ALeft-hand
 d

ipped
 h
eadlamp.
F28 5 ARight-hand
 d

ipped
 h
eadlamp.
Engine compartment fuses
The fusebox is placed in the engine compartment   near   the   battery   (left-hand   side).
Access to the fuses
F Unclip  the   cover.
F  C hange   the   fuse   (see   corresponding  
par

agraph).
F

W
hen you have finished, close the cover
carefully
  to   ensure   sealing   of   the   fusebox.
Fuse table
11
Practical information

256
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
12 V battery
The battery is located under the  bonnet.
For   access   to   the   (+)   terminal:
F
 
r
elease   the   bonnet   using   the   interior   lever,  
t

hen   the   exterior   safety   catch,
F

r
aise the bonnet and secure it with its stay,
F

l
ift the plastic cover for access to
the (+)
  terminal.
Access to the batteryProcedure for starting the engine  u sing   another  b
attery   or   charging   a   discharged   battery.
The presence of this label, in particular
with
  the   Stop   &   Start   system,   indicates
 t

he use of a 12 V lead-acid battery with
special
 t

echnology
 a
nd
 s
pecification;
 t

he   involvement   of   a   CITROËN   dealer   or
 a

  qualified   workshop   is   essential   when
 r

eplacing   or   disconnecting   the   battery.
After refitting the battery, the Stop & Start system  w ill  o nly  b e  a ctive  a fter  a  c ontinuous p

eriod   of   immobilisation   of   the   vehicle,
 a

  period   which   depends   on   the   climatic
 c

onditions   and   the   state   of   charge   of   the
 b

attery   (up   to   about   8   hours).
Practical information

257
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
When your vehicle's battery is discharged, the engine   can   be   started   using   a   slave   battery  
(

external   or   on   another   vehicle)   and   jump   lead  
c

ables.
Starting using another
battery
First check that the slave battery has a n ominal   voltage   of   12   V   and   a   capacity  
a

t   least   equal   to   that   of   the   discharged  
b

attery.
Do
  not   try   to   start   the   engine   by  
c

onnecting   a   battery   charger.
Do
  not   disconnect   the   (+)   terminal   when  
t

he   engine   is   running. F
 
S
tart   the   engine   of   the   vehicle   with   the  
g

ood   battery   and   leave   it   running   for   a   few  
m

inutes.
F  
O
perate   the   starter   on   the   broken   down  
v

ehicle   and   let   the   engine   run. I
f   the   engine   does   not   start   straight   away,  s
witch   off   the   ignition   and   wait   a   few  
m

oments   before   trying   again.
Before disconnecting the battery
Wait 2 minutes after switching off the ignition before   disconnecting   the   battery.
Close the windows and the doors before
disconnecting
  the   battery.
F
 
R

emove
 
the
 
plastic
 
cover
 
from
 

the
 
(+)
 
terminal,
 
if
 
your
 
vehicle
 
has
 
one.
F
C
onnect the red cable to the positive
terminal
 
(+)
 
of
 
the
 
flat
 
battery
 
A , then to the
positive
 
terminal
 
(+)
 
of
 
the
 
slave
 
battery
 
B.
F
 
C

onnect
 
one
 
end
 
of
 
the
 
green
 
or
 
black
 
c

able
 
to
 
the
 
negative
 
terminal
 
(-)
 
of
 
the
 
s

lave battery B
 
(or
 
earth
 
point
 
on
 
the
 
other
 
v

ehicle).
F
 
C

onnect
 
t

he
 
o

ther
 
e

nd
 
o

f
 
t

he
 
g

reen
 
o

r
 
b

lack
 
c

able to the earth point C
 
on
 
the
 
broken
 
d

own
 
vehicle
 
(or
 
on
 
the
 
engine
 
mounting). F
 
W
ait   until   the   engine   returns   to   idle   then  
d

isconnect   the   jump   lead   cables   in   the  
r

everse
 o
rder.
F  
R
efit   the   plastic   cover   to   the   (+)   terminal,   if  
y

our   vehicle   has   one.
11
Practical information

258
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Protect your eyes and face before
handling  the   battery.
All
  operations   on   the   battery   must   be  
c

arried out in a well ventilated area and
away
  from   naked   flames   and   sources  
o

f   sparks,   so   as   to   avoid   the   risk   of  
e

xplosion   or   fire.
Do
  not   try   to   charge   a   frozen   battery;  
t

he   battery   must   first   be   thawed   out   to  
a

void   the   risk   of   explosion.   If   the   battery  
h

as   been   frozen,   before   charging   have  
i

t   checked   by   a   CITROËN   dealer   or   a  
q

ualified   workshop   who   will   check   that  
t

he   internal   components   have   not   been  
d

amaged   and   the   casing   is   not   cracked,  
w

hich   could   cause   a   leak   of   toxic   and  
c

orrosive   acid.
do n

ot reverse the polarity and use only
a
  12   V   charger.
Do
  not   disconnect   the   terminals   while  
t

he   engine   is   running.
Do
  not   charge   the   batteries   without  
d

isconnecting   the   terminals   first.
Wash
  your   hands   after wards.do n ot push the vehicle to start the
engine   if   you   have   an   electronic   or  
a

utomatic   gearbox.
Some
 
functions
 
are
 
not
 
available
 
if
 
the
 
b

attery
 
is
 
not
 
sufficiently
 
charged.
It is advisable to disconnect the battery if
the
 
vehicle
 
is
 
to
 
be
 
left
 
unused
 
for
 
more
 t

han
 
one
 
month.
The batteries contain harmful substances s uch   as   sulphuric   acid   and   lead.   They m

ust   be   disposed   of   in   accordance
 w

ith   regulations   and   must   not,   in   any
 c

ircumstances,   be   discarded   with   household
 w

aste.
Take
  used   remote   control   batteries   and
 v

ehicle   batteries   to   a   special   collection   point.
Practical information

259
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Charging the battery using
a battery charger
F Disconnect   the   battery   from   the   vehicle.
F F ollow the instructions for use provided by
the
  manufacturer   of   the   charger.
F
 
C
onnect   the   battery   starting   with   the  
n

egative   terminal   (-).
F
 
C
heck   that   the   terminals   and   connectors  
a

re   clean.   If   they   are   covered  
w
ith
 s
ulphate
 (

whitish   or   greenish   deposit),   remove   them  
a

nd   clean   them.
Reinitialisation after
reconnection
after any reconnection of the battery, switch on
the  ignition   and   wait   at   least   one   minute   before  
s

tarting,   to   allow   time   for   the   initialisation   of   the  
e

lectronic   systems.
By
  referring   to   the   corresponding   sections,   you  
s

hould   set   or   initialise   the   following   systems  
y

ourself:
-

o
ne-touch electric windows,
-
 
t
ime   and   date,
-
 
a
udio   and   navigation   system   settings.
Check
  that   no   alert   message   or   warning   lamp  
c

omes   on   after   switching   on   the   ignition.
However,
  if   minor   problems   persist   after  
c

arrying   out   these   operations,   contact   a  
C

ITROËN   dealer   or   a   qualified   workshop.
Reconnecting the (+) cable
F Position  the   open   clamp   E of the cable on
the   positive   post   (+)   of   the   battery.
F
 
P
ress   vertically   on   the   clamp   E to position
it
  correctly   on   the   battery.
F
 
L
ock   the   clamp   by   spreading   the  
p

ositioning   lug   and   then   lowering   the   tab   D.
Disconnecting the (+) cable
F Raise   the   locking   tab   D fully to release the
cable t erminal c lamp E.
D
o   not   apply   excessive   force   on   the  
t

ab   as   locking   will   not   be   possible   if   the  
c

lamp   is   not   positioned   correctly;   start  
t

he   procedure   again. With Stop & Start, the battery does not
have
  to   be   disconnected   for   charging.
11
Practical information

260
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Load reduction modeE nergy ec onomy m ode
Switching to economy mode
Once this period has elapsed, a message a
ppears   in   the   screen   indicating   that   the  
v

ehicle   has   switched   to   economy   mode   and   the  
a

ctive   functions   are   put   on   standby.
Exiting economy mode
These functions are reactivated automatically the   next   time   the   vehicle   is   driven.
F
 
I
n   order   to   resume   the   use   of   these   functions
 i

mmediately,   start   the   engine   and   let   it   run   for   a
 f

ew
 m
inutes.
The
  time   available   to   you   will   then   be   double  
t

he   period   for   which   the   engine   is   left   running.  
H

owever, this period will always be between
five
  and   thirty   minutes.
System
 
which
 
manages
 
the
 
use
 
of
 
certain
 
f

unctions
 
according
 
to
 
the
 
level
 
of
 
charge
 
r

emaining
 
in
 
the
 
battery.
When
 
the
 
vehicle
 
is
 
being
 
driven,
 
the
 
load
 
r

eduction
 
function
 
temporarily
 
deactivates
 
c

ertain
 
functions,
 
such
 
as
 
the
 
air
 
conditioning,
 
t

he
 
heated
 
rear
 
screen...
The deactivated functions are reactivated
automatically
 
as
 
soon
 
as
 
conditions
 
permit. System
 
which
 
manages
 
the
 
period
 
of
 
use
 
of
 
certain
  functions   to   conserve   a   sufficient   level   of  
c

harge
 
in
 
the
 
battery.
After
 
the
 
engine
 
has
 
stopped,
 
you
 
can
 
still
 
use
 
functions   such   as   the   audio   equipment,   windscreen  
w

ipers,
 
dipped
 
beam
 
headlamps,
 
courtesy
 
lamps,
 
etc.   for
 a m
aximum
 c
ombined
 p
eriod
 o
f
 t
hirty  
m

inutes.
A  flat   battery   prevents   the   engine   from  
s

tarting   (refer   to   the   corresponding  
par

agraph).
This
 
period
 
may
 
be
 
greatly
 
reduced
 
if
 
t

he
 
battery
 
is
 
not
 
fully
 
charged.
If
 
the
 
telephone
 
is
 
being
 
used
 
at
 
the
 
s

ame
 
time
 
on
 
the
 
navigation
 
system,
 i

t
 
w

ill
 
be
 
interrupted
 
after
 
1

0
 m

inutes.
Practical information

261
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Changing a wiper blade
Before removing a front
wiper blade
F Within  one   minute   after   switching   off  t
he   ignition,   operate   the   wiper   stalk   to  
p

osition the wiper blades vertically on the
windscreen.
Removing
F Raise   the   corresponding   wiper   arm.
F  U nclip   the   wiper   blade   and   remove   it.
Fitting
F Put  the   corresponding   new   wiper   blade   in  p
lace   and   clip   it.
F
 
F
old   down   the   wiper   arm   carefully.
After fitting a front wiper
blade
F Switch  on   the   ignition.
F  O perate   the   wiper   stalk   again   to   park   the  
w

iper   blades.
11
Practical information

262
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Very cold climate screen*
* According to country.
Fitting
F Offer  up   the   very   cold   climate   screen   to  t
he front of the lower section of the front
b u m p e r.
F
 
P
ress   around   its   edge   to   engage   its   fixing  
c

lips   one   by   one.
Removal
F Use  a   screwdriver   as   a   lever   to   release  e
ach   fixing   clip   in   turn.
Removable
  protective   screen   which   prevents  
t

he   accumulation   of   snow   at   the   radiator  
c

ooling   fan.
Fitting roof bars
For safety reasons and to avoid damaging the roof, it is essential to use the transverse bars a
pproved   for   your   vehicle.
When
  fitting   roof   bars,   use   only   the   four   fixing  
p

oints   located   in   the   roof   frame.   The   points   are  
m

asked   by   the   vehicle   doors   when   closed.
The
  roof   bar   fixings   include   a   stud   to   be   fitted   to  
t

he   hole   at   each   fixing   point.
Observe
  the   fitting   instructions   and   the  
c

onditions   of   use   in   the   guide   supplied   with   the  
b

ars. Do
  not   forget   to   remove   the   very   cold  
c

limate   screen   when:
-
 
t
he   ambient   temperature   exceeds  
1

0   °C,
-
 tow

ing,
-
 
d
riving   at   speeds   above   75 mph  
(

120   km/h).
Maximum
  load   distributed   over   the   roof  
b

ars,   for   a   load   height   not   exceeding  
4

0 cm   (except   bicycle   carriers):
-

f
or roof bars with pads at 90 mm:
 
5

0 kg,
-

f
or roof bars with pads at 15 0

mm:
 
8

0 kg.
For
  more   information,   contact   a  
C

ITROËN   dealer   or   a   qualified  
w

orkshop.
If
  the   height   exceeds   40   cm,   adapt   the  
s

peed of the vehicle to the profile of the
road
  to   avoid   damaging   the   roof   bars  
a

nd   the   fixings   on   the   vehicle.
Be
  sure   to   refer   to   local   legislation   in  
o

rder   to   comply   with   the   regulations   for  
t

ransporting   objects   which   are   longer  
t

han   the   vehicle.
Practical information