2015 AUDI Q7 Owner´s Manual

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
-Jumper cables must be long enough so
that the vehicles do not t ouch.
- W hen connecting jumper ca bles, make
sure that they cannot get caught in any
moving parts in the eng ine compart­
ment.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
Q page 256.
(D Note
Improper hook-up of jumper cables can ru­
in the generator.
- Always connect POSITIVE( +) to POSI ­
TIVE(+), and NEGATIVE(-) to NEGATIVE
( - ) ground post of the battery manager
control unit.
- Check that all screw plugs on the battery
cells are screwed in firmly. If not, tighten plugs prior to connecting clamp on nega­
tive battery terminal.
- Please note that the procedure for con­
nect ing a jumper cable as described
above applies spec ifically to the case of
your vehicle be ing jump started . When
you are giving a jump start to another ve­
hi cle, do
not connec t the negat ive (-) ca­
ble to the negat ive( -) term inal on the
discharged battery ©¢
fig. 2 73. In ­
stead, securely connect the negative( -)
cable to e ither a solid metal component
that is firmly bolted to the engine block
or to the engine block itse lf. If the bat­
tery that is being charged does not vent
to the outside, escaping battery gas
could ignite and exp lode!
Em erg en cy si tuation s 319
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
ing.
T he following information is to be used by
commercial tow t ruck operators who know
how to operate their equipment safely.
- Never tow your Audi , towing will cause
damage to the engine a nd transmi ssion.
- Never wrap th e safet y chain s or winch c a­
ble s around th e brak e lin es.
- To prevent unne ce ss ary dam age, your Aud i
mu st be t ransp orted with a flat bed truck .
- To load th e vehi cle on to the fl at bed, us e
the t owing loop found in the vehicle t ool s
and atta ch to the front or rear anch o rage
¢ page 320 and Qpage 320 .
A WARNING
A vehicle being towed is not safe for pas­
sengers. Never allow anyone to ride in a
vehicle be ing towed, for any reason.
-
•
•

320 Emergency situations
Front towing loop
Do not install the front towing loop until it is
needed.
Fig. 274 Right fron t bumper: Removing t he cover
Fig. 275 Righ t fron t bumper wit hout cove r: Screwing
i n towing loop
The towing loop fits into the threaded hole lo­
cated on the right side of the front bumper
and covered by a cover when not in use.
• Remove the towing loop from the vehicle
tool kit
c> page 304.
• Carefully remove the cover c> fig. 274.
• Screw the towing loop tightly into the
threaded hole as far as it will go
c> fig . 2 75 .
When it is no longer needed, unscrew the
towing loop and put it back into the vehicle
toolkit. Be sure to have the towing loop stored
in the vehicle at all times .
A WARNING
If the towing loop is not screwed in as far
as it will go, the thread can pull out when
the vehicle is towed -potential risk of an
accident.
Rear towing loop
Do not install the rear towing loop until it is
needed .
Fig. 276 Rear bumper: Cover
Fig. 277 Rea r bumper: Screw ing in tow ing loop
On the right sid e of the rear bumper there is a
threaded hole for the towing loop. The
threaded hole is protected by a cover.
• Remove the towing loop from the vehicle
tool kit
c> page 304 .
• To release the cover from the bumper, press
it in by applying short, sharp pressure to the
outer part
c> fig . 2 76.
• Screw the towing loop tightly into the
threaded hole as far as it will go
c> fig. 2 77.
Unscrew the towing loop again afte r use and
install the cover in the bumper. Return the
towing loop to the toolkit . Be sure to have the
towing loop stored in the vehicle at a ll times.
A WARNING
If the towing loop is not screwed in as far
as it will go, the thread can pull out when
the veh icle is towed - potential risk of an
accident.

M
"' 0 ..J
"". rl I.O
"' rl
"' rl
Loading the vehicle onto a flat bed truck
Fig. 278 Ve hicle on fla t bed tr uck
Front hook up
.. Align the vehicle with the centerline of the
car carr ier ramp.
.. Attach the winch hook to the front towline
eye previously installed .
Rear hook up
.. Align the vehicle w ith the centerline of the
car carrier ramp.
.. Attach the winch hook to the rear towline
eye previously installed.
(D} Tips
Check carefully to make sure the hook- up
is secure before moving the car up the flat­
bed truck ramp .
Lifting vehicle
Lifting with workshop hoist and with
floor jack
The vehicle may only be li~ed at the lifting
points illustrated .
Fig. 279 Fro nt l ift ing po int
Emergenc y situ ation s 321
Fig. 280 Rea r liftin g po int
.,. Read and heed WARNING c::> .&, .
.,. Locate lifting points c::> fig. 2 79 and
¢ fig. 280 .
.,. Adju st lifting arms of wo rkshop ho ist o r
floor jack to ma tch veh icle lifting points.
.. Insert a rubbe r pad be tween the floor jack/
workshop hoist and the lift ing points.
If y ou mu st lift your veh icl e with a fl oor jack
to w ork und erneath , be sure the vehicle is
safel y supported on stand s intended for thi s
purpo se .
Front lifting point
T he lifti ng point is loca ted o n the floo r pan re­
i nforcemen t abo ut a t the same level as the
jack mounting point
c::> fig. 279. Do not lift
the vehicle at the vertic al sill reinforcement.
Rear lifting point
T he lifting point is located o n the vert ica l rein­
f o rcement of the lower s ill for the on board
jack
c::> fig. 280 .
Lifting with vehicle jack
Refer to c:;, page 309.
A WARNING
-To reduce the risk of ser ious injury and
veh icle damage.
- Always lift the vehicle only at the spe­
cia l workshop hoist and floor jack lift
points illustrated
c:;, fig. 279 and
c:;, fig. 280.
- Fail ure to lift the veh icle at these
-
po ints could cause the vehicle to tilt or ..,.

322 Emergency situations
fall from a lift if there is a change in ve­
hicle weight distribution and balance.
This might happen, for example, when
heavy components such as the engine
block or transmission are removed .
- When removing heavy components like
these, anchor vehicle to hoist or add cor­
responding weights to maintain the cen­
ter of gravity. Otherwise, the vehicle
might tilt or slip off the hoist, causing
serious personal injury.
(D Note
- Be aware of the following points before
lifting the vehicle:
-The vehicle should never be lifted or
jacked up from underneath the engine
oil pan, the transmission housing, the
front or rear axle or the body side
members. This could lead to serious
damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity
of the hoist.
- Before driving over a workshop hoist,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.

Technical Data
Vehicle identification
F ig. 281 Veh ide Identificat ion Number (VlN) plate: lo ·
c ation on d river 's s ide das h pane l
XXXXX XX · X -XXXX XXX
~ fAllftlli. -llllll · NR. ~ W!ru -llllll -NO.
xx
XXXX XXXX XX X XXXXXXXX
XXX XXX
IYP /TYPE
XX XXXXXXX XX X X XX
XXX KW XXX
®i ~W.::·f :l~~ XXXX XXX XXX
©+ ::rw= xxxx I xxxx XXX I xx
M. · AUSSt I IJ'IIDIIS
~--
EOA 7D 5 4UB 6XM SSG SRW
2E H JDZ 1LB lA S 18A
3FC SMU 7X l
FD A 9G3 OG7 OYH OJF
TL6 3 KA 8EH UlA X98 027
lXW 803 908 824 D2D
7T6 CV7 7KO 4X3 2K2
3L4 4KC 3YO 413 502
1S A 7GB 01A 4GO
XX. X XX X XX X XXXX
Fig. 282
Vehicle identificat io n label: inside the lug­
ga ge compar tmen t
Vehicle Identification Number (VlN)
The Veh icle Iden tifica tion Number is located
in different p laces :
- under the windshield on the driver's side
¢fig. 281.
-in the MMI: Select: !CAR ! function button>
Systems* contro l bu tton > Vehicle ID num­
ber (VIN)
or select: I CAR I function button >
Car systems* control button > Servicing &
~ checks > VIN number .
:3 -on the vehicle identification label. ""'. rl I.O
"' rl
"' rl
Technical Data 323
Vehicle identification label
The vehicle identification label is located in
the luggage compartment under the cargo
floor cover.
T he label¢
fig. 282 shows the following vehi­
cle data :
(D Vehicle Ident ificat ion Number (VIN)
@ Vehicle type, engine o utput, transmission
® Engine and transmission code
© Paint number and interior
® Optional equipment numbers
The information of the vehicle identification
label can also be found in your Warranty
&
Maintenance booklet.
Safety compliance sticker
The safety compliance sticker is your assur­
ance that your new veh icle complies with all
applicable Federal Motor Vehicle Safety
Standards which were in effect at the time the
vehicle was manufactured . You can find this
sticker on the door jamb on the driver's side.
It shows the month and year of production
and the vehicle ident ificat ion number of your
vehicle (perforation) a s well as the Gross Veh i­
cle Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
High voltage warning label
The high voltage warning label is located in
the engine compartment next to the engine hood re lease. The spark ign ition system com­
plies with the Ca nadian standard ICES-002 .
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticke r on the
door jamb on the driver's side .
The Gross Vehicle Weight Rating includes the
weight of the bas ic vehicle plus full fuel tank,
o il and coolant, plus maximum load, which in ­
cludes passenger we ight (150 lbs/68 kg per
II>--

324 Technical Dat a
designated seating position) and luggage
weight¢ .&,.
Gross Axle W eight Rating
The Gross Axle Weight Rating is the maximum
l oad that can be applied at each axle of the
vehicle ¢Lr!, .
Vehicle capacit y weight
The vehicle capac ity we ight (max. load) is list­
ed on the driver's side B-p illar.
A WARNING
- T he Gross Vehicle Weight Rat ing for your
vehicle, fo und on the safety compliance
label on the driver's side B -pillar, must
never be exceeded under any circumstan­
ces. Exceeding the Gross Vehicle We ight
Rating of your vehicle is likely to damage
your vehicle, and such damage will not
be covered by your Lim ited New Vehicle
Warranty. Exceeding the Gross Vehicle
We ight Rating will also change the per­
formance and handling cha racte rist ics of
yo ur vehicle, which cou ld cause a crash
result ing in se rious in jury or death.
- T he Gross Veh icle Weight Rat ing fo r yo ur
vehicle would be exceeded if yo ur vehicle
is simultaneo us ly equipped with Panor­
amic sliding sunroo f; th ird-row seating;
Dimensions
Length
Width
Width (across mirrors) Height (unloaded) al trailer towing
equipment (factory or
dea le r-installed), and running boards
(dealer-installed). UNDER NO CIRCUM­
STANCES MAY ALL SUCH ITEMS BE IN­
STA LLED ON THE SAME VE HICLE .
- The actual Gross Ax le Weig ht Rating at
the front and rear ax les should not ex­
ceed the permissible weights, and the ir
comb inat io n must not exceed the Gross
Vehi cle Weight Rating.
- Exceeding permiss ible weight ratings can
result i n ve hicl e damage, a ccidents and
personal inj ury.
....--
CD Note
- The vehicle capacity weight figu res apply
when the load is d istr ibuted evenly in the
vehicle (passenge rs and luggage). When
t ransport ing a heavy load in the lugg age
compar tment, carry the load as near to
t he rear ax le as possible so that the vehi ­
cle's handling is not impaired.
- Do not exceed the maximum permissib le
ax le loads or the maximum gross vehicle
we ight . A lways remember that the vehi ­
cle's handling w ill be affected by the ex­
tra load. Therefore, ad just your speed ac­
cordingly.
- Always observe local regulat ions.
in (mm)
200 .3 (5089)
in (mm) 78.1 (1983)
in (mm) 85 .7 (2 177)
in (mm) 68.4 (1737)
al The he ight of the veh icle depen ds on the tires and th e su spension.
When driv ing up steep ramps, on rough roads,
over curbs, etc . it is important to remember
that some parts of your vehicle, such as spoil-ers
or exha ust system components, may be
close to the ground. Be carefu l not to damage
them.
1

M N
0 ...J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Technical Dat a
Capacities
Fuel tank: tota l capacity gal (liters) approx. 26.4 (100)
Windshield and headlight* washer fluid container quarts (liters) approx. 4.8 (4.5)
Gasoline engines
Q7 3.0, 6 cylinder (280 hp)
Maximum output SAE net hp@ rpm 280 @ 4900 - 6500
Maximum torque SAE net lb-ft@ rpm 295@ 2150 - 4900
Displacement CID (cm
3
) 182 .8 (2995)
Engine oil with f ilter change q
uarts ( lite rs) 7.2 (6 .8)
Fuel
Pr emium unlea ded (91 AKI), Q page 248, Fuel supply
Q7 3.0, 6 cylinder (333 hp)
Maximum output SAE net hp@ rpm
333 @ 5500 -6500
Maximum torque SAE net l
b -ft@ rpm 325@ 2900 -5300
Displacement CID (cm
3
) 182 .8 (2995)
Engine oil with filter change q
uarts (liters) 7.2 (6 .8)
Fuel Pr emium unlead ed (9 1 AKI) , Q page 248, Fuel supply
Diesel engine
Q7 3.0 TOI, 6 cylinder
Maximum outpu t SA E net hp@rpm 240@ 3500 - 4000
Maximum torque SAE net lb-ft@ rpm 406@ 1750 -2250
Displa cement CID (cm
3
) 181. 1 (2967)
Engine oil with filter change quarts (liters) 8.1 (7.7)
F uel
ULSD No . 2 , Q page 249, Diesel fuel
325
•
•

326 Consumer Information
Consumer Information
Warranty coverages
You r Audi i s covered by the following war­
ranties:
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfo-
ration
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Control Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warran­
ties can be found in your
Warranty & Mainte­
nance booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regu lations in the United States
and Canada require that automobiles meet
specific emission regulations and safety
standards. Therefore, veh icles built for the
U.S.A . and Canada differ from vehicles sold in
other countries .
If you p lan to take your vehicle outside the
continental limits of the United States or Can­
ada, there is the possibility that:
- unleaded fuels for vehicles with cata lytic
converter may not be available;
- fuel may have a considerably lowe r octane
rating. Improper fuel may cause engine
damage ;
- service may be inadequate due to lack of
proper service facilities, tools or testing
equipment ;
- replacement pa rts may not be readily availa­
ble.
- Navigation systems for vehicles built for the
U.S.A. and Canada will not necessar ily work
in Europe, and may not work in other coun­
tries outside North America .
(D Note
Audi cannot be responsible for mechanical
damage that could result from inadequate
fuel, service or parts availability.
Audi Service Repair Manuals and Literature
Audi Official Factory Service Manuals and Lit ­
erature are published as soon as possible after
model introduction. Service Manuals and liter­
ature are available to order from the Audi
T echnical Literature Ordering Center at:
www.audi.techliterature.com
Maintenance
General
Your vehicle has been designed to help keep
maintenance requirements to a minimum.
However, a certain amount of regular mainte­
nance is still necessary to assure your vehicle's
s afety, economy and rel iability. For detailed
vehicle maintenance consult your Warranty &
Maintenance booklet.
Under difficult operating conditions, for ex­
ample at extremely low outside temperatures,
i n very dusty regions , when towing a trailer
very frequently, etc., some service work
should be performed between the intervals
specified. This applies particularly to:
- oil changes, and
- cleaning or replacing the air filter .
(® For the sake of the environment
By regularly maintaining your vehicle, you
help make sure that emission standards
are maintained, thus minimizing adverse
effects on the environment.
Important considerations for you and
your vehicle
The increasing use of electronics, sophisticat­
ed fuel injection and emission contro l sys-
tems, and the genera lly increasing technical
liJJ,