2014 NISSAN TEANA lock

PWC-10
< SYSTEM DESCRIPTION >[LH FRONT ONLY ANTI-PINCH]
SYSTEM
SYSTEM
System DiagramINFOID:0000000009460821
FRONT POWER WINDOW LH ANTI-PINCH SYSTEM
System DescriptionINFOID:0000000009460822
MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
INPUT/OUTPUT SIGNAL CHART
POWER WINDOW OPERATION
• Power window system is activated by the power window
switch when the ignition switch is in the ON position
or during the retained power operation after ignition switch is turned OFF.
• Main power window and door lock/unlock switch can open/close all windows.
• Front & rear power window switches can open/close the corresponding windows.
• Power window lock switch can lock all power windows other than driver seat.
• If door glass receives resistance that is more than t he specified value and the power window is in the AUTO-
UP operation (Front LH), power window will move in the reverse direction (Anti-Pinch Function).
POWER WINDOW AUTO-OPERATION (FRONT LH)
ABKIA3026GB
ItemInput signal to main power window and
door lock/unlock switch Main power window and door
lock/unlock switch function Actuator
Encoder Encoder pulse signal
Power window controlFront power window motor
Main power window
and door lock/unlock
switch Front power window motor LH UP/
DOWN signal
Power window and
door lock/unlock
switch RH Front power window motor RH UP/
DOWN signal
BCM RAP signal
Rear power window
switch Rear power window motor UP/DOWN
signal Rear power window motor
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SYSTEMPWC-11
< SYSTEM DESCRIPTION > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
• AUTO UP/DOWN operation can be performed when main power window and door lock/unlock switch turns to AUTO.
• Encoder continues detecting the movement of power window motor and transmits to main power window
and door lock/unlock switch as the encoder pulse signal while power window motor is operating.
• Main power window and door lock/unlock switch reads the changes of encoder signal and stops AUTO oper-
ation when door glass is at fully opened/closed position.
• Power window motor is operable in case encoder is malfunctioning.
RETAINED POWER OPERATION
• Retained power operation is an additional power supply function that enables power window system to oper-
ate during the 45 seconds even when ignition switch is turned OFF
Retained power function cancel conditions
• Front door CLOSE (door switch OFF) →OPEN (door switch ON).
• When ignition switch is ON.
• When timer time passes. (45 seconds)
• AUTO function does not operate if encoder is malfunctioning.
POWER WINDOW LOCK FUNCTION
Ground circuit inside main power window and door lock/unlock switch shuts off when power window lock
switch is ON. This inhibits power window switch operation except with the main power window and door lock/
unlock switch.
ANTI-PINCH OPERATION (FRONT LH)
• Pinch foreign material in the door glass during AUTO-U P operation, and it is the anti-pinch function that low-
ers the door glass 150mm. (5.9 in .) or 2 seconds when detected.
• Encoder continues detecting the movement of power window motor and transmits to main power window and door lock/unlock switch as the encoder pulse signal while power window motor is operating.
• Resistance is applied to the power window motor ro tation that changes the frequency of encoder pulse sig-
nal if foreign material is trapped in the door glass.
• Power window switch controls to lower the window gla ss for 150 mm. (5.9 in.) or 2 seconds after it detects
encoder pulse signal frequency change.
OPERATION CONDITION
• When door glass AUTO-UP operation is performed (anti- pinch function does not operate just before the door
glass closes and is fully closed)
NOTE:
Depending on environment and driving conditions, if a similar impact or load is applied to the door glass, it
may lower.
KEYLESS POWER WINDOW DOWN FUNCTION
All power windows open when the unlock button on Intelligent Key is activated and pressed for more than 3
seconds with the ignition switch OFF. The windows keep opening if the unlock button is continuously pressed.
The power window opening stops when the following operations are performed:
• When the unlock button is pressed for more than 15 seconds.
• When the ignition switch is turned ON while the power window opening is operated.
• When the unlock button is released.
While retained power operation activate, keyless power window down function cannot be operated.
Fail-safeINFOID:0000000009460823
FAIL-SAFE CONTROL
Switches to fail-safe control when malfunction is det ected in the encoder signal that detects UP/DOWN speed
and direction of door glass. Switches to fail-safe control when an error beyond the regulation value is detected
between the fully closed position and the actual position of the glass.
Malfunction Malfunction condition
Pulse sensor malfunction When only one side of pulse signal is being detected for more than the specified value.
Both pulse sensors mal-
function When both pulse signals have not been detected for more than the specified value during glass
open/close operation.
Pulse direction malfunc-
tion When the pulse signal that is detected during glass open/close operation detects the opposite con-
dition of power window motor operating direction.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DIAGNOSIS SYSTEM (BCM)PWC-13
< SYSTEM DESCRIPTION > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)INFOID:0000000009955247
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF → ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentiall y causing a discharged battery and a no-start condition.
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode Description
Ecu Identification The BCM part number is displayed.
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components.
Work support The settings for BCM functions can be changed.
Configuration • The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN Diag Support Mntr The result of transmit/receive diagnosis of CAN communication is displayed.
System Sub System Direct Diagnostic Mode
Ecu Identification
Self Diagnostic Result
Data Monitor
Active Test
Work support
Configuration
CAN Diag Su pport Mntr
Door lock DOOR LOCK ××××
Rear window defogger REAR DEFOGGER ×××
Warning chime BUZZER ××
Interior room lamp timer INT LAMP ×××
Remote keyless entry system MULTI REMOTE ENT ×××
Exterior lamp HEADLAMP ×××
Wiper and washer WIPER ×××
Turn signal and hazard warning lamps FLASHER ××
Air conditioner AIR CONDITIONER ×
Intelligent Key system INTELLIGENT KEY ××××
Combination switch COMB SW ×
BCM BCM × × ×××
Immobilizer IMMU ×××
Interior room lamp battery saver BATTERY SAVER ××
Trunk open TRUNK ×
Vehicle security system THEFT ALM ×××
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-16
< ECU DIAGNOSIS INFORMATION >[LH FRONT ONLY ANTI-PINCH]
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH
Reference Value INFOID:0000000009460827
TERMINAL LAYOUT
PHYSICAL VALUES
MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
AWKIA2368ZZ
Te r m i n a l N o . (Wire color) Description
ConditionVo l ta g e
(Approx.)
+ - Signal name Input/
Output
1
(B) Ground Ground — — 0
2
(L) 16Front power window motor
RH DOWN signal OutputWhen front RH switch in
power window main switch
is operated DOWN. Battery voltage
4
(BG) 12 Encoder pulse signal 2 Input When power window mo-
tor operates.
5
(R) 12 Encoder pulse signal 1 Input
When power window mo-
tor operates.
6
(SB) Ground Rear power window motor RH
DOWN signal OutputWhen rear RH switch in
power window main switch
is operated DOWN. Battery voltage
7
(V) Ground
Rear power window motor RH
UP signal OutputWhen rear RH switch in
power window main switch
is operated UP. Battery voltage
8
(L) Ground Rear power window motor LH
DOWN signal OutputWhen rear LH switch in
power window main switch
is operated DOWN. Battery voltage
JMKIA0070GB
JMKIA0070GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER SUPPLY AND GROUND CIRCUITPWC-29
< DTC/CIRCUIT DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
BCM
BCM : Diagnosis ProcedureINFOID:0000000009955265
Regarding Wiring Diagram information, refer to BCS-55, "Wiring Diagram".
1. CHECK FUSE AND FUSIBLE LINK
Check that the following fuse and fusible link are not blown.
Is the fuse or fusible link blown?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit.
NO >> GO TO 2
2. CHECK POWER SUPPLY CIRCUIT
1. Disconnect BCM connector M21.
2. Check voltage between BCM connector M21 terminals 131, 139 and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness or connectors.
3. CHECK GROUND CIRCUIT
Check continuity between BCM connector M21 terminals 134, 143 and ground.
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair or replace harness or connectors.
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : DescriptionINFOID:0000000009460835
• BCM supplies power.
• It operates each power window motor via corresponding power window switch and makes window move up/
down when main power window and door lock/unlock switch is operated.
Terminal No. Signal name Fuse and fusible link No.
139 Fusible link battery power I (40A)
131 BCM battery fuse 1 (10A)
BCM GroundVo l ta g e
(Approx.)
Connector Terminal
M21 131
—Batteryvoltage
139
BCM Ground Continuity
Connector Terminal
M21 134
—Yes
143
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-30
< DTC/CIRCUIT DIAGNOSIS >[LH FRONT ONLY ANTI-PINCH]
POWER SUPPLY AND GROUND CIRCUIT
POWER WINDOW MAIN SWITCH : Component Function Check
INFOID:0000000009460836
Main Power Window And Door Lock/unlock Switch
1. CHECK MAIN POWER WINDOW AND DO OR LOCK/UNLOCK SWITCH FUNCTION
Check power window motor operation with main power window and door lock/unlock switch.
Is the inspection result normal?
YES >> Main power window and door lock/unlock switch power supply and ground circuit are OK.
NO >> Refer to PWC-30, "POWER WI NDOW MAIN SWITCH : Diagnosis Procedure"
.
POWER WINDOW MAIN SWITCH : Diagnosis ProcedureINFOID:0000000009460837
Regarding Wiring Diagram information, refer to PWC-18, "Wiring Diagram - With Left Front Only Power Win-
dow Anti- Pinch".
Main Power Window And Door Lock/unlock Switch Power Supply Circuit Check
1. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between main power window and door lock/unlock switch connectors D8, D12 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect BCM, main power window and door lock/ unlock switch, power window and door lock/unlock
switch RH, rear power window switch LH and rear power window switch RH.
3. Check continuity between BCM connector and main power window and door lock/unlock switch connec- tors.
4. Check continuity between BCM connector M21 and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the harness or connectors.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch.
Te r m i n a l
Vo l ta g e
(Approx.)
(+)
(–)
Main power window and door lock/unlock switch
Te r m i n a l
D12 10 Ground Battery voltage
D8 18
BCM
connector Te r m i n a l
Main power window and door lock/unlock switch
connector Terminal Continuity
M21 140 D12 10
Ye s
141 D8 18
BCM connector Terminal GroundContinuity
M21 140
No
141
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER SUPPLY AND GROUND CIRCUITPWC-31
< DTC/CIRCUIT DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
3. Check continuity between main power window and door lock/unlock switch connector D8 and ground.
Is the inspection result normal?
YES >> Check main power window and door lock/unlock switch output signal (rear power window switch
LH) GO TO 5.
YES >> Check main power window and door lock/unlock switch output signal (rear power window switch
RH) GO TO 6.
YES >> Check main power window and door lock/unlock s witch output signal (front power window switch
LH) GO TO 7.
YES >> Check main power window and door lock/unlock s witch output signal (front power window switch
RH) GO TO 8.
NO >> Repair or replace the harness or connectors.
4. CHECK BCM OUTPUT SIGNAL
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M21 and ground.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Replace BCM. Refer to BCS-80, "Removal and Installation"
.
5. CHECK MAIN POWER WINDOW AND DOOR LOCK /UNLOCK SWITCH OUTPUT SIGNAL (REAR POW-
ER WINDOW SWITCH LH)
1. Connect main power window and door lock/unlock switch.
2. Turn ignition switch ON.
3. Check voltage between main power window and door lock/unlock switch D12 and ground.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement".
6. CHECK MAIN POWER WINDOW AND DOOR LOCK /UNLOCK SWITCH OUTPUT SIGNAL (REAR POW-
ER WINDOW SWITCH RH)
1. Connect main power window and door lock/unlock switch.
2. Turn ignition switch ON.
3. Check voltage between main power window and door lock/unlock switch D12 and ground.
Main power window and door lock/unlock switch connector Terminal GroundContinuity
D8 1 Yes
Te r m i n a l s Vo l ta g e
(Approx.)
(+)
(–)
BCM connector Terminal
M21 140
Ground Battery voltage
141
Te r m i n a l
Window switch
position (rear LH) Vol tag e
(Approx.)
(+)
(–)
Main power window and door lock/
unlock switch connector Te r m i n a l
D12 8
Ground UP Battery voltage
DOWN 0
9 UP 0
DOWN Battery voltage
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-32
< DTC/CIRCUIT DIAGNOSIS >[LH FRONT ONLY ANTI-PINCH]
POWER SUPPLY AND GROUND CIRCUIT
Is the inspection result normal?
YES >> Check intermittent incident. Refer to
GI-43, "Intermittent Incident".
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement".
7. CHECK MAIN POWER WINDOW AND DOOR LO CK/UNLOCK SWITCH OUTPUT SIGNAL (FRONT
POWER WINDOW SWITCH LH)
1. Connect main power window and door lock/unlock switch.
2. Turn ignition switch ON.
3. Check voltage between main power window and door lock/unlock switch D8 and ground.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement".
8. CHECK MAIN POWER WINDOW AND DOOR LO CK/UNLOCK SWITCH OUTPUT SIGNAL (FRONT
POWER WINDOW SWITCH RH)
1. Connect main power window and door lock/unlock switch.
2. Turn ignition switch ON.
3. Check voltage between main power window and door lock/unlock switch D12 and ground.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
Te r m i n a l
Window switch
position (rear RH) Vo l ta g e
(Approx.)
(+)
(–)
Main power window and door
lock/unlock switch connector Te r m i n a l
D12 6
Ground UP Battery voltage
DOWN 0
7 UP 0
DOWN Battery voltage
Te r m i n a l Window switch
position (front LH) Vo l ta g e
(Approx.)
(+)
(–)
Main power window and door lock/
unlock switch connector Te r m i n a l
D8 17
Ground UP Battery voltage
DOWN 0
19 UP 0
DOWN Battery voltage
Te r m i n a l Window switch
position (front RH) Vo l ta g e
(Approx.)
(+)
(–)
Main power window and door
lock/unlock switch connector Te r m i n a l
D12 2
Ground UP Battery voltage
DOWN 0
16 UP 0
DOWN Battery voltage
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM