2014 NISSAN TEANA drain bolt

CONTROL VALVETM-187
< REMOVAL AND INSTALLATION > [CVT: RE0F10D]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Removal and InstallationINFOID:0000000009464131
REMOVAL
1. Disconnect battery negative terminal. Refer to XX-XX, "*****".
2. Remove drain plug from oil pan and then drain the CVT fluid.
3. Remove drain plug gasket. CAUTION:
Do not reuse drain plug gasket.
4. Remove the front fender side cover (LH). Refer to XX-XX, "*****"
.
5. Disconnect the CVT unit harness connector.
6. Remove the snap ring (1) from the CVT unit harness connector (A).
7. Press the CVT unit harness connector (A) into the transaxle case.
CAUTION:
Do not damage the CVT unit harness connector.
NOTE:
Clean around the harness connector to prevent foreign materi-
als from entering into the transaxle case.
8. Remove the oil pan bolts, and then remove the oil pan and oil pan gasket. CAUTION:
Do not reuse oil pan gasket.
9. Remove the magnets from the oil pan.
10. Remove the lock nut (1) and spring washer (2), and manual plate from manual shaft (A).
: Apply petroleum jelly
: Apply CVT fluid
JPDIA0654ZZ
JPDIA0720ZZ
: Front
JSDIA3685ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

CONTROL VALVETM-191
< REMOVAL AND INSTALLATION > [CVT: RE0F10D]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
12. Install the snap ring (1) to the CVT unit harness connector (A).
13. Connect the CVT unit harness connector.
14. Install fender protector side cover (LH). Refer to XX-XX, "*****"
.
15. Install the magnet while aligning it with the convex side of oil pan. CAUTION:
Completely clean the iron powder from the magnet area of oil pan and the magnet.
16. Install the oil pan to the transaxle case with the following procedure. 1. Install the oil pan gasket to the oil pan. CAUTION:
• Completely wipe out an y moisture, oil, and old gasket fr om the oil pan gasket surface and
bolt hole of oil pan and transaxle case.
• Do not reuse oil pan gasket.
2. Install the oil pan assembly to the transaxle case, and then temporarily tighten the oil pan bolt.
3. Tighten the oil pan bolts in the order shown to the specified
torque.
4. Tighten the oil pan bolts again clockwise from (1) shown to the specified torque.
17. Install drain plug gasket to drain plug. CAUTION:
Do not reuse drain plug gasket.
18. Install drain plug to oil pan.
19. Connect battery negative terminal. Refer to XX-XX, "*****"
.
20. Fill with CVT fluid to transaxle assembly. Refer to XX-XX, "*****"
.
InspectionINFOID:0000000009464132
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or ch ips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Check the CVT fluid level and leakage. Refer to TM-178, "Inspection".
JPDIA0654ZZ
: Front
JPDIA0664ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-388
< REMOVAL AND INSTALLATION >[CVT: RE0F10E]
CONTROL VALVE
Removal and Installation
INFOID:0000000009464345
REMOVAL
1. Disconnect battery negative terminal. Refer to PG-73, "Removal and Installation (Battery)".
2. Remove drain plug from oil pan and then drain the CVT fluid.
3. Remove drain plug gasket. CAUTION:
Do not reuse drain plug gasket.
4. Remove the front fender side protector (LH). Refer to EXT-26, "FENDER PROTECTOR : Exploded View"
.
5. Disconnect the CVT unit harness connector.
6. Remove the snap ring (1) from the CVT unit harness connector (A).
7. Press the CVT unit harness connector (A) into the transaxle case.
CAUTION:
Do not damage the CVT unit harness connector.
NOTE:
Clean around the harness connector to prevent foreign materi-
als from entering into the transaxle case.
8. Remove the oil pan bolts, and then remove the oil pan and oil pan gasket. CAUTION:
Do not reuse oil pan gasket.
9. Remove the magnets from the oil pan.
10. Remove the lock nut (1) and spring washer (2), and manual plate from manual shaft (A).
: Apply petroleum jelly
: Apply CVT fluid
JPDIA0654ZZ
JPDIA0720ZZ
: Front
JSDIA3685ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-392
< REMOVAL AND INSTALLATION >[CVT: RE0F10E]
CONTROL VALVE
12. Install the snap ring (1) to the CVT unit harness connector (A).
13. Connect the CVT unit harness connector.
14. install fender protector side cover (LH).
15. Install the magnet while aligning it with the convex side of oil
pan.
CAUTION:
Completely clean the iron powder from the magnet area of
oil pan and the magnet.
16. Install the oil pan to the transaxle case with the following proce- dure.
1. Install the oil pan gasket to the oil pan. CAUTION:
• Completely wipe out any moisture, oil, and old gasket from the oil pan gasket surface and
bolt hole of oil pan and transaxle case.
• Do not reuse oil pan gasket.
2. Install the oil pan assembly to the transaxle case, and then temporarily tighten the oil pan bolt.
3. Tighten the oil pan bolts in the order shown to the specified torque.
4. Tighten the oil pan bolts again clockwise from (1) shown to the specified torque.
17. Install drain plug gasket to drain plug. CAUTION:
Do not reuse drain plug gasket.
18. Install drain plug to oil pan.
19. Connect battery negative terminal. Refer to PG-73, "Removal
and Installation (Battery)".
20. Fill with CVT fluid to transaxle assembly. Refer to TM-377, "Inspection"
.
InspectionINFOID:0000000009464346
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Check the CVT fluid level and leakage. Refer to TM-377, "Inspection".
: Front
JPDIA0654ZZ
JPDIA0664ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

WASHER TANKWW-51
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
WW
N
O P
REMOVAL AND INSTALLATION
WASHER TANK
Exploded ViewINFOID:0000000009464628
Removal and InstallationINFOID:0000000009464629
REMOVAL
1. Drain the washer fluid.
2. Remove the front under cover. Refer to EXT-28, "Removal and Installation"
.
3. Remove the fender protector (RH). Refer to EXT-26, "FENDER PROTECTOR : Removal and Installation"
.
4. Disconnect the harness connectors from the washer pump and washer level switch.
5. Disconnect the front washer tube from the washer pump.
6. Disconnect the rear washer tube from the washer pump (if equipped).
7. Remove the washer tank bolts, then remove the washer tank.
8. Remove the washer pump, washer level switch, and wa sher tank seals from the washer tank (if neces-
sary).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• After installation, add water to the top of the washer tank inlet to check that no leaks exist.
• Fill washer tank with specified amount of fluid. Refer to WW-66, "Specifications"
.
1. Washer tank 2. Washer level switch 3. Washer tank seal
4. Washer pump (without rear washer tube) 5. Washer pump (with rear washer tube) 6. Washer tank inlet
AWLIA2228ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM