2014 NISSAN TEANA ignition

EC-90
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
VIAS S/V-1• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
•No load When revving engine up to 5,000 rpm
quickly Off
→ On → Off
AIR COND RLY • Engine: After warming up, idle the
engine Air conditioner switch: OFF Off
Air conditioner switch: ON
(Compressor operates) On
FUEL PUMP RLY • For 1 second after turning ignition switch: ON
• Engine running or cranking On
• Except above Off
VENT CONT/V • Ignition switch: ON Off
THRTL RELAY • Ignition switch: ON On
COOLING FAN • Engine: After warming up, idle the
engine
• Air conditioner switch: OFF Engine coolant temperature is 97
°C
(207 °F) or less Off
Engine coolant temperature between
98 °C (208 °F) and 99 °C (210 °F) or more Low
Engine coolant temperature between
100 °C (212 °F) or more Hi
• Engine: After warming up, idle the engine
• Air conditioner switch: ON
• Refrigerant pressure is less than 1,280 kPa (12.80 bar, 13.05 kg/
cm
2, 185.6 psi) Engine coolant temperature is 97
°C
(207 °F) or less Off
Engine coolant temperature between
98 °C (208 °F) and 99 °C (210 °F) or more Mid
Engine coolant temperature between
100 °C (212 °F) or more Hi
HO2S2 HTR (B1) • Engine speed: Below 3,600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load On
• Engine speed: Above 3,600 rpm Off
ALT DUTY SIG • Power generation voltage variable control: Operating On
• Power generation voltage variable control: Not operating Off
I/P PULLY SPD • Vehicle speed: More than 20 km/h (12 MPH) Almost the same speed as
the tachometer indication
VEHICLE SPEED • Turn drive wheels and compare CONSULT value with the speedometer indi-
cation. Almost the same speed as
the speedometer indication
IDL A/V LEARN • Engine: running Idle air volume learning has not been per-
formed yet. YET
Idle air volume learning has already been
performed successfully. CMPLT
TRVL AFTER MIL • Ignition switch: ON Vehicle has traveled after MIL has turned
ON. 0 - 65,535 km
(0 - 40,723 miles)
ENG OIL TEMP • Engine: After warming up More than 70 °C (158 °F)
A/F S1 HTR(B1) • Engine: After warming up, idle the engine
(More than 140 seconds after starting engine.) 4 - 100%
VHCL SPEED SE • Turn drive wheels and compare CONSULT value with the speedometer indi-
cation. Almost the same speed as
the speedometer indication
SET VHCL SPD • Engine: Running ASCD: Operating The preset vehicle speed is
displayed
MAIN SW • Ignition switch: ON MAIN switch: Pressed On
MAIN switch: Released Off
Monitor Item Condition Values/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-91
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
CANCEL SW • Ignition switch: ON
CANCEL switch: Pressed On
CANCEL switch: Released Off
RESUME/ACC SW • Ignition switch: ON RESUME/ACCELERATE switch:
Pressed On
RESUME/ACCELERATE switch: Re-
leased Off
SET SW • Ignition switch: ON SET/COAST switch: Pressed On
SET/COAST switch: Released Off
BRAKE SW1
(Brake pedal posi-
tion switch) • Ignition switch: ON Brake pedal: Fully released On
Brake pedal: Slightly depressed Off
BRAKE SW2
(Stop lamp switch) • Ignition switch: ON Brake pedal: Fully released Off
Brake pedal: Slightly depressed On
VHCL SPD CUT • Ignition switch: ON Non
LO SPEED CUT • Ignition switch: ON Non
AT OD MONITOR • Ignition switch: ON Off
AT OD CANCEL • Ignition switch: ON Off
CRUISE LAMP • Ignition switch: ON MAIN switch: Pressed at the 1st time
→
at the 2nd time On
→ Off
SET LAMP • MAIN switch: ON
• When vehicle speed: Between 40 km/h (25 MPH) and 144 km/h (89
MPH) ASCD: Operating On
ASCD: Not operating Off
ALT DUTY • Engine speed: Idle 0 - 80%
BAT CUR SEN • Engine speed: Idle
• Battery: Fully charged
*2
• Selector lever: P or N
• Air conditioner switch: OFF
•No load Approx. 2,600 - 3,500 mV
A/F ADJ-B1 • Engine: running –0.330 - 0.330
TUMBLE POS SEN • Ignition switch: ON
• Engine coolant temperature: Be-
tween -12 °C (10 °F) and 59 °C
(138 °F) Accelerator pedal: Fully released Less than 1.4 V
Accelerator pedal: Fully depressed More than 2.8 V
P/N POSI SW • Ignition switch: ON Selector lever: P or N On
Selector lever: Except above Off
INT/A TEMP SE • Ignition switch: ON Indicates intake air tempera-
ture
AC PRESS SEN • Engine speed: Idle
• Both A/C switch and blower fan switch: ON (Compressor operates) 1.0 - 4.0 V
VTC DTY EX B1 • Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
•No load Idle 0 - 2%
2,000 rpm Approx. 0- 90%
EVAP LEAK DIAG • Ignition switch: ON Depending on condition of
EVAP leak diagnosis
EVAP DIAG READY • Ignition switch: ON Depending on ready condi-
tion of EVAP leak diagnosis
BAT TEMP SEN • Engine: After warming up, idle the engine
• Selector lever: P or N
• Air conditioner switch: OFF
•No load Indicates the temperature
around the battery.
Monitor Item Condition Values/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-93
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
Terminal No.
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
Output
1
(G) 128
(GR) Throttle control motor
(Close) Output[Ignition switch: ON]
• Engine stopped
• Selector lever: D
• Accelerator pedal: Fully released 1.8 V
2
(R) 128
(GR) Throttle control motor
power supply Input [Ignition switch: ON]
Battery voltage
(11 - 14 V)
3
(BG) 128
(GR) Throttle control motor
(Open) Output[Ignition switch: ON]
• Engine stopped
• Selector lever: D
• Accelerator pedal: Fully depressed 3.2 V
4
(W) 8
(B) Knock sensor Input [Engine is running]
• Idle speed 2.5 V
5
(W) 128
(GR) Intake manifold tuning
valve motor (Close) Output[Ignition switch ON]
• Engine coolant temperature: more than -30 °C (-22 °F)
• Accelerator pedal: Depressed → ful-
ly released Battery voltage appears for about
1 second.
6
(L) 128
(GR) Intake manifold tuning
valve motor power supply Input [Ignition switch: ON]
Battery voltage
(11 - 14 V)
7
(B) 128
(GR) Intake manifold tuning
valve motor (Open) Output[Ignition switch ON]
• Engine coolant temperature: more
than -30 °C (-22 °F)
• Accelerator pedal: Fully released →
depressed Battery voltage appears for about
1 second.
8
(B) —Sensor ground
(Knock sensor) —— —
9
(Y) 10
(BR)
13
(BR) 14
(Y) 128
(GR) Fuel injector No. 4
Fuel injector No. 3
Fuel injector No. 1
Fuel injector No. 2 Output[Engine is running]
• Warm-up condition
• Idle speed NOTE:
The pulse cycle changes depending
on rpm at idle Battery voltage
(11 - 14 V)
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm Battery voltage
(11 - 14 V)
JMBIA0326GB
JMBIA0324GB
JMBIA0089GB
JMBIA0090GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-94
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
12
(B) — ECM ground — — —
16
(B) — ECM ground — — —
17
(V) 128
(GR) EVAP canister purge vol-
ume control solenoid
valve Output[Engine is running]
• Idle speed
• Accelerator pedal: Not depressed even slightly, after engine starting Battery voltage
(11 - 14 V)
[Engine is running]
• Engine speed: About 2,000 rpm (More than 100 seconds after start-
ing engine.) Battery voltage
(11 - 14 V)
18
(V) 128
(GR) Fuel pump relay Output [Ignition switch: ON]
• For 1 second after turning ignition switch ON
[Engine is running] 0 - 1.0 V
[Ignition switch: ON]
• More than 1 second after turning ig- nition switch ON Battery voltage
(11 - 14 V)
21
(BR) 128
(GR) Throttle control motor re-
lay Output[Ignition switch: OFF]
Battery voltage
(11 - 14 V)
[Ignition switch: ON] 0 - 1.0 V
22
(L) 23
(B) Heated oxygen sensor 2 Input [Engine is running]
• Revving engine from idle to 3,000 rpm quickly after the following condi-
tions are met
- Engine: after warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load 0 - 1.0 V
23
(B) —Sensor ground
(Heated oxygen sensor 2) —— —
25
(L) 26
(G) Engine oil temperature
sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine oil temperature.
26
(G) —Sensor ground
(Engine oil temperature
sensor) —— —
27
(BR) —Sensor ground
(Engine coolant tempera-
ture sensor) —— —
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
Output
JMBIA0087GB
JMBIA0088GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-95
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O28
(SB) 27
(BR) Engine coolant tempera-
ture sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine coolant temperature.
30
(SB) —Sensor ground
[Camshaft position sen-
sor (PHASE)] —— —
31
(LG) 30
(SB) Camshaft position sensor
(PHASE) Input[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle 1.0 - 2.0
[Engine is running]
• Engine speed is 2,000 rpm 1.0 - 2.0
32
(V) —Sensor power supply
[Camshaft position sen-
sor (PHASE)] — [Ignition switch: ON] 5.0 V
33
(V) 34
(BR) Intake air temperature
sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with intake
air temperature.
34
(BR) —Sensor ground
(Mass air flow sensor, in-
take air temperature sen-
sor) —— —
35
(Y) 34
(BR) Mass air flow sensor Input [Ignition switch: ON]
• Engine stopped 1.3 V
[Engine is running]
• Warm-up condition
• Idle speed 1.3 - 1.6 V
[Engine is running]
• Warm-up condition
• Engine is revving from idle to about
4,000 rpm 1.3 - 1.6 to 2.5 V (Check for linear
voltage rise in response to en-gine being increased to about
4,000 rpm.)
36
(SB) —
Sensor power supply
(Mass air flow sensor) — [Ignition switch: ON] 5.0 V
37
(B) — Shield — — —
38
(V) —Sensor ground
(Engine oil pressure sen-
sor) —— —
Terminal No.
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
Output
JPBIA4726ZZ
JPBIA4727ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-96
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
39
(L) 38
(V) Engine oil pressure sen-
sor Input[Engine is running]
• Warm-up condition
• Idle speed 1.3 V
[Engine is running]
• Warm-up condition
• Engine speed is 2,000 rpm 2.7 V
40
(BR) 38
(V) Sensor power supply
(Engine oil pressure sen-
sor) — [Ignition switch: ON] 5.0 V
41
(W) 128
(GR) A/F sensor 1 Input [Ignition switch: ON] 2.2 V
42
(SB) —Sensor ground
[Exhaust valve timing
control position sensor] —— —
43
(LG) 42
(SB) Exhaust valve timing con-
trol position sensor Input[Engine is running]
• Warm-up condition
• Idle speed NOTE:
The pulse cycle changes depending
on rpm at idle 1.0 - 2.0
[Engine is running]
• Engine speed is 2,000 rpm 1.0 - 2.0
44
(V) —Sensor power supply
[Exhaust valve timing
control position sensor] — [Ignition switch: ON] 5 V
45
(B) 128
(GR) A/F sensor 1 Input [Engine is running]
• Engine speed is 2,000 rpm 1.8 V
Output voltage varies with air fuel ratio.
49
(W) 128
(GR) Intake manifold runner
control valve motor
(Close) Output[Ignition switch ON]
• Engine coolant temperature: Be- tween -12 °C (10 °F) and 59 °C
(138 °F)
• Accelerator pedal: Depressed → ful-
ly released Battery voltage appears for about
1 second.
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
OutputJPBIA3359ZZ
JPBIA3360ZZ
JPBIA4730ZZ
JPBIA4731ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-97
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O50
(L) 128
(GR) Intake manifold runner
control valve motor power
supply Input [Ignition switch: ON]
Battery voltage
(11 - 14 V)
51
(B) 128
(GR) Intake manifold runner
control valve motor
(Open) Output[Ignition switch ON]
• Engine coolant temperature: Be- tween -12 °C (10 °F) and 59 °C
(138 °F)
• Accelerator pedal: Fully released →
depressed Battery voltage appears for about
1 second.
52
(B) — ECM ground — — —
53
(BR) 128
(GR) A/F sensor 1 heater Input [Engine is running]
• Warm-up condition
• Idle speed
(More than 140 seconds after start-
ing engine) 2.9 - 8.8 V
54
(Y) 128
(GR) Heated oxygen sensor 2
heater Output[Engine is running]
• Engine speed: Below 3,600 rpm af-
ter the following conditions are met
- Engine: after warming up
- Keeping the engine speed between
3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load 10 V
[Ignition switch: ON]
• Engine stopped
[Engine is running]
• Engine speed: Above 3,600 rpm Battery voltage
(11 - 14 V)
56
(SB) 128
(GR) Intake valve timing inter-
mediate lock control sole-
noid valve Output[Engine is running]
• Warm-up condition
• Idle speed 0 V
[Engine is running]
• Cold condition [Engine coolant tem- perature: below 60 °C (140 °F)]
• Idle speed Battery voltage
(11 - 14 V)
58
*1
(L) —Sensor ground
[Manifold absolute pres-
sure (MAP) sensor] —— —
59
*1
(LG) 58
*1
(L)Manifold absolute pres-
sure (MAP) sensor Output[Engine is running]
• Warm-up condition
• Both A/C switch and blower fan switch: ON (Compressor operates) 4.6 V
Output voltage atmospheric pressure.
[Engine is running]
• Warm-up condition
• Idle speed 1.2 V
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 1.5 V
60
*1
(V) —Sensor power supply
[Manifold absolute pres-
sure (MAP) sensor] — [Ignition switch: ON] 5.0 V
Terminal No.
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
Output
JPBIA4732ZZ
JMBIA0325GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-98
< ECU DIAGNOSIS INFORMATION >[QR25DE]
ECM
61
(W) 62
(R) Battery temperature sen-
sor Input[Engine is running]
• Battery temperature: 25 °C ( °F)
• Idle speed 3.3 V
62
(R) —Sensor ground
(Battery curre nt sensor,
battery temperature sen-
sor) —— —
63
(G) 62
(R) Battery current sensor Input [Engine is running]
• Battery: Fully charged
*2
• Idle speed 2.6 - 3.5 V
64
(O) —Sensor power supply
(Battery curre nt sensor) — [Ignition switch: ON] 5.0 V
70
(SB) —Sensor ground
[Crankshaft position sen-
sor (POS)] —— —
71
(LG) 70
(SB) Crankshaft position sen-
sor (POS) Input[Engine is running]
• Warm-up condition
• Idle speed NOTE:
The pulse cycle changes depending
on rpm at idle 4.0 V
[Engine is running]
• Engine speed: 2,000 rpm 4.0 V
72
(V) —Sensor power supply
[Crankshaft position sen-
sor (POS)] — [Ignition switch: ON] 5.0 V
73
(B) —Shield — — —
77
(R) 78
(B) Throttle position sensor 2 Input [Ignition switch: ON]
• Engine stopped
• Selector lever: D
• Accelerator pedal: Fully released Less than 4.75 V
[Ignition switch: ON]
• Engine stopped
• Selector lever: D
• Accelerator pedal: Fully depressed More than 0.36 V
78
(B) —Sensor ground
(Throttle position sensor
1, 2) —— —
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
Output
JPBIA4728ZZ
JPBIA4729ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM