2014 NISSAN TEANA relay

BCS-22
< SYSTEM DESCRIPTION >[BCM]
DIAGNOSIS SYSTEM (BCM)
After disconnecting the CONSULT vehicle interface (VI)
from the data link connector, the ignition must
be cycled OFF → ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a di scharged battery and a no-start condition.
DATA MONITOR
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)INFOID:0000000009462006
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF → ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a di scharged battery and a no-start condition.
SELF DIAGNOSTIC RESULT
Refer to BCS-52, "DTC Index".
DATA MONITOR
Monitor Item [Unit] Description
FAN ON SIG [On/Off] Indicates condition of fan switch.
AIR COND SW [On/Off] Indicates condition of A/C switch.
Monitor Item [Unit] Main Description
REQ SW -DR [On/Off] ×Indicates condition of door request switch LH.
REQ SW -AS [On/Off] ×Indicates condition of door request switch RH.
REQ SW -BD/TR [On/Off] ×Indicates condition of trunk opener request switch.
PUSH SW [On/Off] Indicates condition of push-button ignition switch.
SHFTLCK SLNID PER SPLY [On/Off] ×Indicates condition of power supply to shiftlock solenoid.
BRAKE SW 1 [On/Off] ×Indicates condition of brake switch.
BRAKE SW 2 [On/Off] Indicates condition of brake switch.
DETE/CANCL SW [On/Off] ×Indicates condition of P (park) position.
SFT PN/N SW [On/Off] ×Indicates condition of P (park) or N (neutral) position.
UNLK SEN -DR [On/Off] ×Indicates condition of door unlock sensor.
PUSH SW -IPDM [On/Off] Indicates condition of push-button ignition switch received from IPDM E/R
on CAN communication line.
IGN RLY1 -F/B [On/Off] Indicates condition of ignition relay 1 received from IPDM E/R on CAN
communication line.
DETE SW -IPDM [On/Off] Indicates condition of detent switch received from TCM on CAN communi-
cation line.
SFT PN -IPDM [On/Off] Indicates condition of P (park) or N (neutral) position from TCM on CAN
communication line.
SFT P -MET [On/Off] Indicates condition of P (park) position from TCM on CAN communication
line.
SFT N -MET [On/Off] Indicates condition of N (neutral) position from IPDM E/R on CAN commu-
nication line.
ENGINE STATE [STOP/START/CRANK/RUN] ×Indicates condition of engine state from ECM on CAN communication line.
VEH SPEED 1 [mph/km/h] ×Indicates condition of vehicle speed signal received from ABS on CAN
communication line.
VEH SPEED 2 [mph/km/h] ×Indicates condition of vehicle speed signal received from combination
meter on CAN communication line.
DOOR STAT -DR [LOCK/READY/UNLK] ×Indicates condition of driver side door status.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS
DIAGNOSIS SYSTEM (BCM)BCS-23
< SYSTEM DESCRIPTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
ACTIVE TEST
DOOR STAT -AS [LOCK/READY/UNLK]
×Indicates condition of passenger side door status.
DOOR STAT -RR [LOCK/READY/UNLK] ×Indicates condition of rear right side door status.
DOOR STAT -RL [LOCK/READY/UNLK] ×Indicates condition of rear left side door status.
ID OK FLAG [Set/Reset] Indicates condition of Intelligent Key ID.
PRMT ENG STRT [Set/Reset] Indicates condition of engine start possibility.
PRMT RKE STRT [Set/Reset] Indicates condition of engine start possibility from Intelligent Key.
I-KEY OK FLAG [Key ON/Key OFF] ×Indicates condition of Intelligent Key OK flag.
PRBT ENG STRT [Set/Reset] Indicates condition of engine start prohibit.
ID AUTHENT CANCEL TIMER [STOP] Indicates condition of Intelligent Key ID authentication.
ACC BATTERY SAVER [STOP] Indicate s condition of battery saver.
CRNK PRBT TMR [On/Off] In dicates condition of crank prohibit timer.
AUT CRNK TMR [On/Off] Indicates condition of automatic engine crank timer from Intelligent Key.
CRNK PRBT TME [sec] I ndicates condition of engine crank prohibit time.
AUTO CRNK TME [sec] Indicates co ndition of automatic engine crank time from Intelligent Key.
CRANKING TME [sec] Indicates condition of engine cranking time from Intelligent Key.
DETE SW PWR [On/Off] Indicates condition of detent switch voltage.
ACC RLY -REQ [On/Off] Indicates condition of accessory relay control request.
RKE OPE COUN1 [0-19] ×When remote keyless entry receiver receives the signal transmitted while
operating on Intelligent Key, the numerical value start changing.
RKE OPE COUN2 [0-19] ×When remote keyless entry receiver receives the signal transmitted while
operating on Intelligent Key, the numerical value start changing.
TRNK/HAT MNTR [On/Off] Indicates condition of trunk room lamp switch.
RKE-LOCK [On/Off] Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off] Indicates condition of unlock signal from Intelligent Key.
RKE-TR/BD [On/Off] Indicates condition of trunk open signal from Intelligent Key.
RKE-PANIC [On/Off] Indicates condition of panic signal from Intelligent Key.
RKE-MODE CHG [On/Off] Indicates condition of mode change signal from Intelligent Key. Monitor Item [Unit] Main Description
Test Item Description
INTELLIGENT KEY LINK (CAN) This test is able to check Intelligent Key iden
tification number [Off/ID No1/ID N02/ID No3/ID
No4/ID No5].
INT LAMP This test is able to check interior room lamp operation [On/Off].
FLASHER This test is able to check hazard lamp operation [LH/RH/Off].
HORN This test is able to check horn operation [On].
BATTERY SAVER This test is able to check battery saver operation [On/Off].
TRUNK/BACK DOOR This test is able to check trunk actuator operation [Open].
OUTSIDE BUZZER This test is able to check In telligent Key warning buzzer operation [On/Off].
INSIDE BUZZER This test is able to check combination meter warning chime operation [Take Out/Knob/Key/
Off].
INDICATOR This test is able to check combination meter warning lamp operation [KEY ON/KEY IND/Off].
IGN CONT2 This test is able to check ignition relay-2 control operation [On/Off].
ENGINE SW ILLUMI This test is able to check push-bu tton ignition switch START indicator operation [On/Off].
PUSH SWITCH INDICATOR This test is able to check push-button ignition switch indicator operation [On/Off].
ACC CONT This test is able to check ac cessory relay control operation [On/Off].
IGN CONT1 This test is able to check ignition relay-1 control operation [On/Off].
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-24
< SYSTEM DESCRIPTION >[BCM]
DIAGNOSIS SYSTEM (BCM)
WORK SUPPORT
ST CONT LOW This test is able to check starter control relay operation [On/Off].
IGNITION RELAY This test is able to ignition relay operation [On/Off].
REVERSE LAMP TEST This test is able to check reverse lamp illumination operation [On/Off].
TRUNK/LUGGAGE LAMP TEST This test is able to check cargo lamp illumination operation [On/Off].
KEYFOB PW TEST This test is able to check power wind ow operation using the Intelligent Key [Off/DOWN/UP].
SHIFTLOCK SOLENOID TEST This test is able to check shift lock solenoid operation [On/Off]. Test Item Description
Support Item Setting Description
IGN/ACC BATTERY SAVER On* Battery saver function ON.
Off Battery saver function OFF.
REMOTE ENGINE STARTER On* Remote engine start function ON.
Off Remote engine start function OFF.
ANSWERBACK I-KEY LOCK UNLOCK BUZZER Buzzer reminder function by door lock/unlock request switch ON.
HORN Horn chirp reminder function by door lock request switch ON.
Off* No reminder function by door lock/unlock request switch.
INVALID This mode is not used.
ANSWERBACK KEYLESS LOCK UN-
LOCK On
Buzzer or horn chirp reminder when doors are locked/unlocked with
Intelligent Key.
Off* No buzzer or horn chirp reminder when doors are locked/unlocked
with Intelligent Key.
ANSWER BACK On* Horn chirp reminder when doors are locked with Intelligent Key.
Off No horn chirp reminder when doors are locked with Intelligent Key.
RETRACTABLE MIRROR SET On Retractable mirror set ON.
Off* Retractable mirror set OFF.
CONFIRM KEY FOB ID — Intelligent Key ID code can check.
LOCK/UNLOCK BY I-KEY On* Door lock/unlock function from Intelligent Key ON.
Off Door lock/unlock function from Intelligent Key OFF.
ENGINE START BY I-KEY On* Engine start function from Intelligent Key ON.
Off Engine start function from Intelligent Key OFF.
TRUNK/GLASS HATCH OPEN On* Buzzer reminder function by trunk opener request switch ON.
Off Buzzer reminder function by trunk opener request switch OFF.
INTELLIGENT KEY LINK SET On Intelligent Key link set ON.
Off* Intelligent Key link set OFF.
SHORT CRANKING OUTPUT Start70 msec
Starter motor operation duration times.
100 msec
200 msec
End —
INSIDE ANT DIAGNOSIS — This function allows inside key antenna self-diagnosis.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS
BCM (BODY CONTROL MODULE)BCS-31
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
ECU DIAGNOSIS INFORMATION
BCM (BODY CONTROL MODULE)
Reference ValueINFOID:0000000009462016
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure repor ted by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Check Intelligent Key relative signal strength
• Confirm vehicle Intelligent Key antenna signal strength
VALUES ON THE DIAGNOSIS TOOL
Monitor Item Condition Value/Status
ACC BATTERY SAVER When battery saver is OFF. STOP
ACC RLY -REQ When BCM is not requesting accessory relay activation. Off
When BCM is requesting accessory relay activation. On
AIR COND SW A/C switch OFF Off
A/C switch ON On
AIR PRESS FL Front left tire air pressure value kPa, kg/cm
2, psi
AIR PRESS FR Front right tire air pressure value kPa, kg/cm
2, psi
AIR PRESS RL Rear left ti re air pressure value
kPa, kg/cm
2, psi
AIR PRESS RR Rear right ti re air pressure value
kPa, kg/cm
2, psi
AUTO CRNK TME Remote engine start timer duration. sec
AUTO CRNK TMR When the remote engine start timer is OFF. Off
When the remote engine start timer is ON. On
AUTO LIGHT SW Lighting switch OFF Off
Lighting switch AUTO On
BRAKE SW 1 When the brake pedal is released On
When the brake pedal is depressed Off
BRAKE SW2 Brake pedal released Off
Brake pedal depressed On
BUZZER Buzzer in combination meter OFF Off
Buzzer in combination meter ON On
CDL LOCK SW Door lock/unlock switch does not operate Off
Press door lock/unlock switch to the LOCK side On
CDL UNLOCK SW Door lock/unlock switch does not operate Off
Press door lock/unlock switch to the UNLOCK side On
CONFRM ID ALL The key ID does not match any key ID registered to BCM. Yet
The key ID matches any key ID registered to BCM. DONE
CONFIRM ID4 The key ID does not match the fourth key ID registered to BCM. Yet
The key ID matches the fourth key ID registered to BCM. DONE
CONFIRM ID3 The key ID does not match the third key ID registered to BCM. Yet
The key ID matches the third key ID registered to BCM. DONE
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-40
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
60
(L) Ground CAN high Input/
Output ——
61
(Y) Ground Rear defogger relay
output OutputRear window de-
fogger Active Battery voltage
Not activated 0V
62
(BR) Ground Starter relay output Output
Push-button igni-
tion switch ON When selector lever is in P
or N position and the brake
is depressed Battery voltage
When selector lever is in P
or N position and the brake
is not depressed 0V
64
(W) Ground Buzzer output Output Outside warning
buzzer Sounding 0V
Not sounding Battery voltage
66
(R) Ground Blower fan relay out-
put OutputPush-button igni-
tion switch OFF or ACC 0V
ON Battery voltage
67
(W) Ground Ignition electrical re-
lay output 2 OutputPush-button igni-
tion switch OFF or ACC 0V
ON Battery voltage
68
(P) Ground Dimmer signal output Output
Push-button igni-
tion switch ON Either of the following con-
ditions
• Lighting switch OFF
• The area around the ve- hicle is bright (Shine a
light on the optical sen-
sor) 0V
The area around the vehi-
cle is dark (Block the light
from the optical sensor) Battery voltage
69
(L) Ground CVT device output Output — Battery voltage
70
(G) Ground IPDM E/R ignition
output 1 OutputPush-button igni-
tion switch OFF or ACC 0V
ON Battery voltage
71
(V) Ground Driver request switch Input
Front door LH re-
quest switch ON (pressed) 0V
OFF (not pressed) 1.0V
72
(Y) Ground Passenger request
switch InputFront door RH re-
quest switch ON (pressed) 0V
OFF (not pressed) 1.0V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
JPMIA0016GB
JPMIA0016GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-46
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
105
(BR) Ground Right front flasher Output Push-button igni-
tion switch ON Turn signal switch OFF 0V
Turn signal switch RH
6.5 V
107 (W) Ground Low side start switch
LED InputPush-button igni-
tion switch OFF 0V
NOTE:
When the illumination
brightening/dimming level
is in the neutral position
ON
108
(BG) Ground Shift lock solenoid
output Input Selector lever P position 0V
Any position other than P Battery voltage
109 (G) Ground Reverse signal Output Push-button igni-
tion switch ON R position Battery voltage
Any position other than R 0V
111 (Y) Ground ACC LED Output Push-button igni-
tion switch OFF Battery voltage
ACC or ON 0V
11 3 (P) Ground ACC relay output Output Push-button igni-
tion switch OFF 0V
ACC or ON Battery voltage
11 4 (P) Ground Outside key antenna
RH A OutputWhen the front
door RH request
switch is operat-
ed with push-but-
ton ignition switch
OFF When Intelligent Key is in
the antenna detection area
When Intelligent Key is not
in the antenna detection
area
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
PKID0926E
JSNIA0010GB
JMKIA0062GB
JMKIA0063GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-50
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
Fail Safe
INFOID:0000000009462017
DTC Inspection Priority ChartINFOID:0000000009462018
If some DTCs are displayed at the same time, perfo rm inspections one by one based on the following priority
chart.
137
(V) Ground Driver and fuel door
unlock Output Front door LH UNLOCK (actuator is acti-
vated) Battery voltage
Other than UNLOCK (actu-
ator is not activated) 0V
138 (V) Ground Rear door battery Input Push-button ignition switch OFF Battery voltage
139 (W) Ground Fusible link battery
power Input Push-button ignition switch OFF Battery voltage
140
(LG) Ground
Power window igni-
tion power supply Output Push-button ignition switch ON Battery voltage
141 (V) Ground Power window bat-
tery power supply Output Push-button ignition switch OFF Battery voltage
142
(BR) Ground Front door battery Input Push-button ignition switch OFF Battery voltage
143 (B) Ground Ground 1 — Push-button ignition switch ON 0V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
Display contents of CONS ULT Fail-safe Cancellation
B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI-SCANNING Inhibit engine cranking Ignition switch ON → OFF
B2560: STARTER CONT RELAY Inhibit engine cranking 500 ms after the following CAN signal communication status has
become consistent
• Starter control relay signal
• Starter relay status signal
B2562: LO VOLTAGE Inhibit engine cranking 100 ms after the power supply voltage increases to more than 8.8 V
B2608: STARTER RELAY Inhibit engine cranking 500 ms after the following signal communication status becomes
consistent
• Starter motor re lay control signal
• Starter relay status signal (CAN)
B260A: IGNITION RELAY Inhibit engine cranking 500 ms after the following conditions are fulfilled
• IGN relay (IPDM E/R) control signal: OFF (Battery voltage)
• Ignition ON signal (CAN to IPDM E/R): OFF (Request signal)
• Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)
B2617: STARTER RELAY CIRC Inhibit engine cranking 1 second after the starter motor
relay control inside BCM becomes
normal
B2618: BCM Inhibit engine cranking 1 second after the ignition relay (IPDM E/R) control inside BCM be-
comes normal
B261E: VEHICLE TYPE Inhibit engine cranking BCM initialization
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS
BCM (BODY CONTROL MODULE)BCS-51
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
Priority DTC
1 • B2562: LOW VOLTAGE
2 • U1000: CAN COMM CIRCUIT
• U1010: CONTROL UNIT (CAN)
3 • B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING
• B2196: DONGLE UNIT
• B2198: NATS ANTENNA AMP
4 • B2555: STOP LAMP
• B2556: PUSH-BTN IGN SW
• B2557: VEHICLE SPEED
• B2560: STARTER CONT RELAY
• B2601: SHIFT POSITION
• B2602: SHIFT POSITION
• B2603: SHIFT POSI STATUS
• B2604: PNP SW
• B2605: PNP SW
• B2608: STARTER RELAY
• B260A: IGNITION RELAY
• B2614: ACC RELAY CIRC
• B2615: BLOWER RELAY CIRC
• B2616: IGN RELAY CIRC
• B2617: STARTER RELAY CIRC
• B2618: BCM
• B261A: PUSH-BTN IGN SW
• B261B: RES ENG RUN
• B261E: VEHICLE TYPE
• B26F1: IGNITION RELAY
• B26F2: IGNITION RELAY
•B26F6: BCM
• B26FD: SHIFT LOCK SOLENOID
• B26FE: HOOD SWITCH
• B26FF: INTELLIGENT TUNER
• C1729: VHCL SPEED SIG ERR
• U0415: VEHICLE SPEED SIG
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM