2014 NISSAN TEANA battery

PRECAUTIONSDEF-3
< PRECAUTION >
C
D E
F
G H
I
J
K
M A
B
DEF
N
O P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951577
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service t he system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Un it or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or el ectric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three mi nutes before performing any service.
Precaution for WorkINFOID:0000000009463020
• When removing or disassembling each component, be ca reful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusabl e part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
-Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DEF-8
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)INFOID:0000000009956271
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF → ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a di scharged battery and a no-start condition.
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode Description
Ecu Identification The BCM part number is displayed.
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components.
Work support The settings for BCM functions can be changed.
Configuration • The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN Diag Support Mntr The result of transmit/receive diagnosis of CAN communication is displayed.
System Sub System Direct Diagnostic Mode
Ecu Identification
Self Diagnostic Result
Data Monitor
Active Test
Work support
Configuration
CAN Diag Su pport Mntr
Door lock DOOR LOCK ××××
Rear window defogger REAR DEFOGGER ×××
Warning chime BUZZER ××
Interior room lamp timer INT LAMP ×××
Remote keyless entry system MULTI REMOTE ENT ×××
Exterior lamp HEADLAMP ×××
Wiper and washer WIPER ×××
Turn signal and hazard warning lamps FLASHER ××
Air conditioner AIR CONDITIONER ×
Intelligent Key system INTELLIGENT KEY ××××
Combination switch COMB SW ×
BCM BCM × × ×××
Immobilizer IMMU ×××
Interior room lamp battery saver BATTERY SAVER ××
Trunk open TRUNK ×
Vehicle security system THEFT ALM ×××
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DIAGNOSIS SYSTEM (BCM)DEF-9
< SYSTEM DESCRIPTION >
C
D E
F
G H
I
J
K
M A
B
DEF
N
O P
REAR DEFOGGER
REAR DEFOGGER : CONSULT Func tion (BCM - REAR DEFOGGER)INFOID:0000000009956272
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF → ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentiall y causing a discharged battery and a no-start condition.
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
* : Initial setting RAP system RETAINED PWR
×
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR ××××
System Sub System
Direct Diagnostic Mode
Ecu Identification
Self Diagnostic Result
Data Monitor
Active Test
Work support
Configuration
CAN Diag Support Mntr
Monitor Item [Unit] Description
PUSH SW [On/Off] Indicates condition of push-button ignition switch.
REAR DEF SW [On/Off] Indicates condition of rear window defogger switch.
Test Item Description
REAR DEFOGGER This test is able to check rear window defogger operation [Off/On].
Support Item Setting Description
SET R-DEF TIMER MODE3 Rear defogger turns OFF after 1 minute.
MODE2 Rear defogger remains ON until turned OFF.
MODE1* Rear defogger turns OFF after 15 minutes.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR WINDOW DEFOGGER SWITCHDEF-19
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
K
M A
B
DEF
N
O P
DTC/CIRCUIT DIAGNOSIS
REAR WINDOW DEFOGGER SWITCH
WITH MANUAL A/C
WITH MANUAL A/C : DescriptionINFOID:0000000009463031
• The rear window defogger is operated by pre ssing the rear window defogger switch ON.
• The indicator lamp in the rear window defogger switch illuminates while the rear window defogger is ON.
WITH MANUAL A/C : Component Function CheckINFOID:0000000009463032
1. CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION
1. Push ignition switch to ON.
2. Press rear window defogger switch.
3. Check that the indicator lamp of t he rear window defogger switch illuminates.
4. Press rear window defogger switch.
5. Check that the indicator lamp of t he rear window defogger switch extinguishes.
Is the inspection result normal?
YES >> Rear window defogger switch function is OK.
NO >> Refer to DEF-19, "WITH MANUAL A/C : Diagnosis Procedure"
.
WITH MANUAL A/C : Diagnosis ProcedureINFOID:0000000009463033
Regarding Wiring Diagram information, refer to DEF-11, "Wiring Diagram".
1.CHECK REAR WINDOW DEFOGGER RELAY OPERATION
1. Push the ignition switch to ON.
2. Check that an operation noise of rear window defogger relay [located in fuse block (J/B)] can be heard
when pressing the rear window defogger switch ON and OFF.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 5.
2.CHECK FUSE
Check if Fuse 22 from the rear window defogger relay output is blown.
Is the fuse blown?
YES >> Replace the blown fuse after repairing the affected circuit.
NO >> GO TO 3.
3. CHECK FOR VOLTAGE FROM THE REAR WINDOW DEFOGGER RELAY
1. Connect a voltmeter between Fuse block (J/B) and ground.
2. While pressing the rear window defogger switch ON and OFF, check for voltage between Fuse block (J/B)
and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Perform rear window defogger relay diagnosis. Refer to DEF-26, "Diagnosis Procedure"
.
(+)
(–) Condition Voltage (V)
(Approx.)
Fuse block (J/B)
Connector Terminal
M5 4P Ground Rear window de-
fogger switch ON Battery voltage
OFF 0
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DEF-20
< DTC/CIRCUIT DIAGNOSIS >
REAR WINDOW DEFOGGER SWITCH
4.CHECK REAR WINDOW DEFOGGER SWITCH INDICATOR CIRCUIT
1. Press rear window defogger switch.
2. Check for voltage between front air control connector and ground.
Is the inspection result normal?
YES >> Replace front air control. Refer to HAC-161, "Removal and Installation".
NO >> Repair or replace harness.
5.CHECK FRONT AIR CONTROL (REAR WINDOW DEFOGGER SWITCH) FUNCTION
1. Check (“REAR DEF SW”) in BCM - REAR DEF OGGER “DATA MONITOR” mode by using CONSULT.
2. Operate rear window defogger switch and check the status on CONSULT screen.
Is the inspection result normal?
YES >> GO TO 8.
NO >> GO TO 6.
6. CHECK REAR WINDOW DEFO GGER ON SIGNAL CIRCUIT
Check voltage between BCM connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-80, "Removal and Installation".
NO >> GO TO 7.
7. CHECK HARNESS CONTINUITY
1. Push ignition switch to OFF.
2. Disconnect BCM and front air control.
3. Check continuity between BCM connec tor and front air control connector.
4. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
(+) (–) Condition Voltage (V)
(Approx.)
Front air control
Connector Terminal
M37 4 Ground Rear window de-
fogger switch ON Battery voltage
OFF 0
Monitor Item Condition status
REAR DEF SW Rear window defogger
switch Pressed On
Released Off
(+) (–) Condition Voltage (V)
(Approx.)
BCM
Connector Terminal
M17 32 Ground Rear window de-
fogger switch ON 0
OFF 5
BCM Front air control Continuity
Connector Terminal Connector Terminal
M17 32 M37 10 Yes
BCM GroundContinuity
Connector Terminal
M17 32 No
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR WINDOW DEFOGGER SWITCHDEF-21
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
K
M A
B
DEF
N
O P
YES >> Replace front air control. Refer to HAC-161, "Removal and Installation".
NO >> Repair or replace harness.
8. CHECK REAR WINDOW DEFOGGER RELAY GROUND CIRCUIT
CONSULT
1. Select BCM (REAR DEFOGGER) ACTIVE TEST.
2. Turn REAR DEFOGGER active test ON and OFF.
3. Check voltage between fuse block (J/B) connector and ground.
Is the inspection result normal?
YES >> GO TO 11.
NO >> GO TO 9.
9. CHECK REAR WINDOW DEFOGGER RELAY CIRCUIT
Check voltage between fuse block (J/B) connector and ground.
Is the inspection result normal?
YES >> Replace rear window defogger relay.
NO >> GO TO 10.
10. CHECK HARNESS CONTINUITY
1. Push ignition switch to OFF.
2. Disconnect BCM and fuse block (J/B).
3. Check continuity between BCM connector and fuse block (J/B) connector.
4. Check continuity between fuse block (J/B) connector M5 terminal 6P and ground.
Is the inspection result normal?
YES >> Perform rear window defogger relay component inspection. Refer to DEF-27, "Component
Inspection". If OK, replace BCM. Refer to BCS-80, "Removal and Installation".
NO >> Repair or replace harness.
11 . CHECK REAR WINDOW DEFOGGER RELAY
Check rear window defogger relay.
Refer to DEF-27, "Component Inspection"
.
Is the inspection result normal?
(+)
(–) Condition Voltage (V)
(Approx.)
Fuse block (J/B)
Connector Terminal
M5 6P Ground Rear window de-
fogger active test ON 0
OFF Battery voltage
(+) (–) Condition Voltage (V)
(Approx.)
Fuse block (J/B)
Connector Terminal
M5 6P Ground Rear window de-
fogger switch ON 0
OFF Battery voltage
BCM Fuse block (J/B) Continuity
Connector Terminal Connector Terminal
M18 61 M5 6P Yes
Fuse block (J/B) GroundContinuity
Connector Terminal
M5 6P No
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DEF-22
< DTC/CIRCUIT DIAGNOSIS >
REAR WINDOW DEFOGGER SWITCH
YES >> GO TO 12.
NO >> Replace rear window defogger relay.
12. CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to GI-43, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Check the following. • Battery power supply circuit.
• Fuse block (J/B).
NO >> Repair or replace the malfunctioning parts.
WITH AUTO A/C
WITH AUTO A/C : DescriptionINFOID:0000000009463034
• The rear window defogger is operated by pres sing the rear window defogger switch ON.
• The indicator lamp in the rear window defogger switch illuminates while the rear window defogger is ON.
WITH AUTO A/C : Component Function CheckINFOID:0000000009463035
1. CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION
1. Push ignition switch to ON.
2. Press rear window defogger switch.
3. Check that the indicator lamp of t he rear window defogger switch illuminates.
4. Press rear window defogger switch.
5. Check that the indicator lamp of t he rear window defogger switch extinguishes.
Is the inspection result normal?
YES >> Rear window defogger switch function is OK.
NO >> Refer to DEF-22, "WITH AUTO A/C : Diagnosis Procedure"
.
WITH AUTO A/C : Diagnosis ProcedureINFOID:0000000009463036
Regarding Wiring Diagram information, refer to DEF-11, "Wiring Diagram".
1.CHECK REAR WINDOW DEFOGGER RELAY OPERATION
1. Push the ignition switch to ON.
2. Check that an operation noise of rear window defogger relay [located in fuse block (J/B)] can be heard
when pressing the rear window defogger switch ON and OFF.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 5.
2.CHECK FUSE
Check if Fuse 22 from the rear window defogger relay output is blown.
Is the fuse blown?
YES >> Replace the blown fuse after repairing the affected circuit.
NO >> GO TO 3.
3. CHECK FOR VOLTAGE FROM THE REAR WINDOW DEFOGGER RELAY
1. Connect a voltmeter between Fuse block (J/B) and ground.
2. While pressing the rear window defogger switch ON and OFF, check for voltage between Fuse block (J/B) and ground.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REAR WINDOW DEFOGGER SWITCHDEF-23
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
K
M A
B
DEF
N
O P
Is the inspection result normal?
YES >> GO TO 4.
NO >> Perform rear window defogger relay diagnosis. Refer to DEF-26, "Diagnosis Procedure"
.
4.CHECK REAR WINDOW DEFOGGER SWITCH INDICATOR CIRCUIT
1. Press rear window defogger switch.
2. Check for voltage between A/C auto amp. connector and ground.
Is the inspection result normal?
YES >> Replace A/C auto amp. Refer to HAC-102, "Removal and Installation".
NO >> Repair or replace harness.
5.CHECK A/C AUTO AMP. (REAR WI NDOW DEFOGGER SWITCH) FUNCTION
1. Check (“REAR DEF SW”) in BCM - REAR DEFOGG ER “DATA MONITOR” mode by using CONSULT.
2. Operate rear window defogger switch and check the status on CONSULT screen.
Is the inspection result normal?
YES >> GO TO 8.
NO >> GO TO 6.
6. CHECK REAR WINDOW DEFOGGER ON SIGNAL CIRCUIT
Check voltage between BCM connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-80, "Removal and Installation".
NO >> GO TO 7.
7. CHECK HARNESS CONTINUITY
1. Push ignition switch to OFF.
2. Disconnect BCM and front air control.
3. Check continuity between BCM connector and A/C auto amp.
(+)
(–) Condition Voltage (V)
(Approx.)
Fuse block (J/B)
Connector Terminal
M5 4P Ground Rear window de-
fogger switch ON Battery voltage
OFF 0
(+) (–) Condition Voltage (V)
(Approx.)
A/C auto amp.
Connector Terminal
M152 35 Ground Rear window de-
fogger switch ON Battery voltage
OFF 0
Monitor Item Condition status
REAR DEF SW Rear window defogger
switch Pressed On
Released Off
(+) (–) Condition Voltage (V)
(Approx.)
BCM
Connector Terminal
M17 32 Ground Rear window de-
fogger switch ON 0
OFF 5
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM