2014 NISSAN TEANA engine

CO-16
< REMOVAL AND INSTALLATION >[QR25DE]
RADIATOR
REMOVAL AND INSTALLATION
RADIATOR
Exploded ViewINFOID:0000000009460392
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high-pressure
engine coolant escaping from the radiator. Wrap a th ick cloth around the cap. Slowly push down and
turn it a quarter turn to allow built-up pressure to escape. Carefully remove the cap by pushing it down
and turning it all the way.
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
1. Radiator 2. CVT oil cooler hose 3. Radiator hose (upper)
4. Radiator hose (lower) 5. Radiator core support 6. Reservoir tank
7. Reservoir tank cap 8. Reservoir tank hose 9. Radiator filler cap
10. Filler neck 11. Filler neck hose A. To CVT
B. To water outlet C. To water inlet
AWBIA1321ZZ
Revision: November 20132014 Altima NAM

RADIATORCO-17
< REMOVAL AND INSTALLATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
CO
NP
O
Removal and InstallationINFOID:0000000009460393
REMOVAL
1. Remove radiator cap and drain coolant from radiator. Refer to
CO-12, "Changing Engine Coolant".
CAUTION:
• Perform this step when the engine is cold.
• Do not spill coolant on the drive belt.
2. Remove front air duct. Refer to EM-84, "Removal and Installation"
.
3. Disconnect coolant reservoir hose from the radiator.
4. Remove fender protector side cover (LH/RH). Refer to EXT-26, "FENDER PROTECTOR : Exploded
View".
5. Disconnect radiator hose (upper) and radiat or hose (lower) from the radiator.
CAUTION:
Do not allow the coolant to contact the drive belt.
NOTE:
The radiator hose clamps on the radiator hose (upper ) and on the radiator hose (lower), are not serviced
separately. Radiator hose clamps are part of the radiator hose assembly and serviced as one unit with the
radiator hose.
6. Disconnect the CVT oil cooler hoses.
7. Remove the front bumper fascia. Refer to EXT-17, "Removal and Installation"
.
8. Remove A/C condenser. Refer to HA-30, "COMPRESSOR : Removal and Installation"
.
CAUTION:
Be careful not to damage condenser core.
9. Remove the radiator mounts (upper).
10. Remove radiator. CAUTION:
Do not damage or scratch the radiator core when removing.
INSTALLATION
Installation is in the reverse order of removal.
• After installation, refill coolant and check for leaks. Refer to CO-12, "Changing Engine Coolant"
and CO-11,
"System Inspection".
CAUTION:
Do not spill coolant in engi ne compartment. Use a shop cloth to absorb coolant.
InspectionINFOID:0000000009460394
INSPECTION AFTER INSTALLATION
• Check that the reservoir tank cap is tightened.
• Check for leakage of engine coolant using Tool (B) and suitable tool (A). Refer to CO-11, "System Inspection"
.
WARNING:
Do not remove the radiator cap wh en the engine is hot. Seri-
ous burns could occur from high pressure coolant escaping
from the radiator.
CAUTION:
Higher pressure than specified may cause radiator damage.
• Start and warm up the engine. Visually check that there is no leakage of engine coolant and CVT fluid.
Tool number : EG17650301 (J-33984-A)
Testing pressure : Refer to CO-26, "Radiator"
.
AWBIA0740ZZ
Revision: November 20132014 Altima NAM

CO-18
< REMOVAL AND INSTALLATION >[QR25DE]
COOLING FAN
COOLING FAN
Exploded ViewINFOID:0000000009460395
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high-pressure
engine coolant escaping from the radiator. Wrap a th ick cloth around the cap. Slowly push down and
turn it a quarter turn to allow built-up pressure to escape. Carefully remove the cap by pushing it down
and turning it all the way.
NOTE:
• When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from
spilling.
• Replace the radiator shroud and cooling fan assembly as a unit. Do not replace cooling fan motors or cool-
ing fan blades separately.
Removal and InstallationINFOID:0000000009460396
REMOVAL
1. Partially drain engine coolant from the radiator. Refer to CO-36, "Changing Engine Coolant".
CAUTION:
• Perform when engine is cold.
• Do not spill coolant on the drive belt.
2. Remove engine room cover. Refer to EM-28, "Removal and Installation"
.
1. Radiator core support 2. Fan shroud and motor assembly 3. Grommet
AWBIA1275GB
Revision: November 20132014 Altima NAM

COOLING FANCO-19
< REMOVAL AND INSTALLATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
CO
NP
O
3. Remove the core support cover clips (A), then remove the core
support cover (1).
4. Remove front air duct. Refer to EM-144, "Removal and Installation"
.
5. Remove air cleaner and air duct assembly. Refer to EM-29, "Removal and Installation"
.
6. Remove battery tray and battery tray bracket. Refer to PG-74, "Removal and Installation (Battery Tray)"
.
7. Disconnect radiator hose (upper) from radiator.
8. Disconnect the harness connectors from the fan motor.
9. Remove fan shroud and motor assembly.
INSTALLATION
Installation is in the reverse order of removal.
• After installation refill engine coolant and check for leaks. Refer to CO-36, "Changing Engine Coolant"
and
CO-35, "System Inspection"
.
CAUTION:
Do not spill coolant in engi ne compartment. Use a shop cloth to absorb coolant.
• Cooling fans are controlled by ECM. Refer to EC-74, "On Board Diagnosis Function"
.
ALKIA2602ZZ
Revision: November 20132014 Altima NAM

CO-20
< REMOVAL AND INSTALLATION >[QR25DE]
WATER PUMP
WATER PUMP
Exploded ViewINFOID:0000000009460397
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high-pressure
engine coolant escaping from the radiator. Wrap a th ick cloth around the cap. Slowly push down and
turn it a quarter turn to allow built-up pressure to escape. Carefully remove the cap by pushing it down
and turning it all the way.
CAUTION:
• When removing water pump assembly, be car eful not to get coolant on drive belt.
• Water pump cannot be disassembled and should be replaced as a unit.
• After installing water pump, connect hose and clamp securely, then check for leaks using radiator
cap tester.
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
Removal and InstallationINFOID:0000000009460398
REMOVAL
1. Drain engine coolant from the radiator. Refer to CO-12, "Changing Engine Coolant".
CAUTION:
Perform when the engine is cold.
2. Remove the core support cover clips (A), then remove the core support cover (1).
ALBIA0823GB
1. Water pump 2-5. Tightening order 6. Gasket
7. Water pump housing 8-11. Tightening order 12. Water pipe
13. Gasket 14. O-ring
ALKIA2602ZZ
Revision: November 20132014 Altima NAM

WATER PUMPCO-21
< REMOVAL AND INSTALLATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
CO
NP
O
3. Remove fender protector side cover (RH). Refer to
EXT-26, "FENDER PROTECTOR : Removal and
Installation".
4. Remove engine under cover. Refer to EXT-17, "Removal and Installation"
.
5. Remove engine room cover. Refer to EXT-17, "Removal and Installation"
.
6. Remove front air duct. Refer to EM-84, "Removal and Installation"
.
7. Remove generator. Refer to CHG-32, "Removal and Installation"
.
8. Remove water pump bolts.
9. Remove the water pump and gasket, as necessary. CAUTION:
• Handle the water pump vane so that it does not contact any other parts.
• Water pump cannot be disassembled an d should be replaced as an assembly.
10. Remove water pipe, O-rings, water pump housing, and gasket.
INSPECTION AFTER REMOVAL
• Visually check that there is no significant dirt or rusting on the water pump body and vane.
• Check that there is no looseness in the vane shaft, and that it turns
smoothly when rotated by hand.
• If the water pump does not perform properly, replace the water pump assembly.
INSTALLATION
Installation is in the reverse order of removal.
• When inserting water pipe end to cylinder block, apply a mild soap to O-ring. Then insert it immediately.
CAUTION:
Do not reuse O-rings.
Do not reuse gasket.
INSPECTION AFTER INSTALLATION
• After installation refill engine coolant and check for leaks. Refer to CO-12, "Changing Engine Coolant" and
CO-11, "System Inspection"
.
ALBIA0939ZZ
Revision: November 20132014 Altima NAM

CO-22
< REMOVAL AND INSTALLATION >[QR25DE]
THERMOSTAT AND THERMOSTAT HOUSING
THERMOSTAT AND THERMOSTAT HOUSING
Exploded ViewINFOID:0000000009460399
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high-pressure
engine coolant escaping from the radiator. Wrap a th ick cloth around the cap. Slowly push down and
turn it a quarter turn to allow built-up pressure to escape. Carefully remove the cap by pushing it down
and turning it all the way.
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
Removal and InstallationINFOID:0000000009460400
REMOVAL
1. Drain engine coolant from the radiator. Refer to CO-12, "Changing Engine Coolant".
CAUTION:
Perform when the engine is cold.
2. Remove the core support cover clips (A), then remove the core support cover (1).
3. Remove the front air duct. Refer to EM-29, "Removal and Installation"
.
4. Remove engine under cover. Refer to EXT-17, "Removal and Installation"
.
5. Remove radiator hose (lower) from the water inlet side.
6. Remove exhaust manifold heat shield.
7. Remove water inlet and thermostat.
INSPECTION AFTER REMOVAL
1. Water inlet 2. Thermostat 3. Rubber ring
ALBIA0824GB
ALKIA2602ZZ
Revision: November 20132014 Altima NAM

THERMOSTAT AND THERMOSTAT HOUSINGCO-23
< REMOVAL AND INSTALLATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
CO
NP
O
• Place a thread so that it is caught
in the valves of the thermostat.
Immerse fully in a container filled with water. Heat while stirring.
• The valve opening temperature is the temperature at which the
valve opens and the thermostat falls from the thread.
• Continue heating. Check the full-open lift amount. NOTE:
The full-open lift amount standard temperature for the thermostat is
the reference value.
• After checking the full-open lift amount, lower the water tempera-
ture and check the valve closing temperature.
• If valve setting at measured values are out of standard range, replace thermostat.
INSTALLATION
Installation is in the reverse order of removal.
• Install the thermostat with the whole circumference of the flange fit-
ting securely inside the rubber ring.
• Install the thermostat with the jiggle valve facing upwards. The
position deviation may be within the range of ±10 °.
• After installation, refill coolant and check for leaks. Refer to CO-
12, "Changing Engine Coolant" and CO-11, "System Inspection".
SLC252B
Thermostat Standard Values
Valve opening temperature Refer to CO-26, "Thermostat"
Full-open lift amount Refer to CO-26, "Thermostat"
Valve closing temperature Refer to CO-26, "Thermostat"
PBIC0157E
Revision: November 20132014 Altima NAM