2014 NISSAN TEANA steering

A
B
C
D
E
F
G
H
I
J
K
L
M
N
P
O
QUICK REFERENCE INDEX
AGENERAL INFORMATIONGIGeneral Information
BENGINEEMEngine Mechanical
LUEngine Lubrication System
COEngine Cooling System
ECEngine Control System
FLFuel System
EXExhaust System
STRStarting System
ACCAccelerator Control System
CHYBRIDHBCHybrid Control System
DTRANSMISSION & DRIVE-LINECLClutch System
TMTransaxle & Transmission
DLNDriveline
FAXFront Axle
RAXRear Axle
ESUSPENSIONFSUFront Suspension
RSURear Suspension
SCSSuspension Control System
WTRoad Wheels & Tires
FBRAKESBRBrake System
PBParking Brake System
BRCBrake Control System
GSTEERINGSTSteering System
STCSteering Control System
HRESTRAINTSSBSeat Belt
SBCSeat Belt Control System
SRSRS Airbag
SRCSRS Airbag Control System
IVENTILATION, HEATER &
AIR CONDITIONERVTLVentilation System
HAHeater & Air Conditioning System
HACHeater & Air Conditioning Control System
JBODY INTERIORINTInterior
IPInstrument Panel
SESeat
ADPAutomatic Drive Positioner
KBODY EXTERIOR, DOORS, ROOF & VEHICLE
SECURITYDLKDoor & Lock
SECSecurity Control System
GWGlass & Window System
PWCPower Window Control System
RFRoof
EXTExterior
BRMBody Repair Manual
LDRIVER CONTROLSMIRMirrors
EXLExterior Lighting System
INLInterior Lighting System
WWWiper & Washer
DEFDefogger
HRNHorn
MELECTRICAL & POWER
CONTROLPWOPower Outlet
BCSBody Control System
LANLAN System
PCSPower Control System
CHGCharging System
PGPower Supply, Ground & Circuit Elements
NDRIVER INFORMATION &
MULTIMEDIAMWIMeter, Warning Lamp & Indicator
WCSWarning Chime System
SNSonar System
AVAudio, Visual & Navigation System
OCRUISE CONTROLCCSCruise Control System
DASDriver Assistance System
PMAINTENANCEMAMaintenance
All rights reserved. No part
of this Service Manual may
be reproduced or stored in a
retrieval system, or transmit-
ted in any form, or by any
means, electronic, mechani-
cal, photo-copying, record-
ing or otherwise, without the
prior written permission of
Nissan North America, Inc.
Edition: August 2013
Revision: November 2013
Pub. No. SM14E00L33U1

< SERVICE DATA AND SPECIFICATIONS (SDS) 2014
QUICK REFERENCE CHART: ALTIMA
Fluids and Lubricants
INFOID:0000000010112411
Description Capacity (Approximate)
Metric US measure Imp measure
Fuel QR25DE
68 18 gal
15 gal
VQ35DE
Engine oil
Drain and refill With oil filter
change
QR25DE
4.6 4-7/8 qt
4 qt
VQ35DE 4.8 5-1/8 qt
4-1/4 qt
Without oil fil-
ter change QR25DE
4.3 4-1/2 qt
3-3/4 qt
VQ35DE 4.5 4-3/4 qt
4 qt
Dry engine
(engine overhaul) QR25DE
5.4 5-3/4 qt
4-3/4 qt
VQ35DE 5.3 5-5/8 qt
4-5/8 qt
Cooling system
(with reservoir tank
at MAX level) QR25DE
7.9 8-3/8 qt
7 qt
VQ35DE 9.2 9-3/4 qt
8-1/8 qt
CVT fluid RE0F10D
7.4 7-7/8 qt
6-1/2 qt
RE0F10E 8.2 8-5/8 qt
7-1/4 qt
Power steering fluid (E-PSF) 1.1 1-1/8 qt
1 qt
Brake fluid ———
Multi-purpose grease ———
Windshield washer fluid 4.5 4-3/4 qt
4 qt
Air conditioner system refrigerant 0.525 ± 0.025 kg 1.158 ± 0.055 lb 1.158 ± 0.055 lb
Air conditioner system oil 150 m5.1 fl oz
5.3 fl oz

BCS
COMBINATION SWITCHBCS-81
< REMOVAL AND INSTALLATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
COMBINATION SWITCH
Exploded ViewINFOID:0000000009462045
NOTE:
Shown with the steering wheel removed for clarity only.
Removal and InstallationINFOID:0000000009462046
REMOVAL
CAUTION:
• Before servicing, turn the ignition switch OFF, disconnect both battery terminals and wait at least
three minutes.
• Do not use air tools or electric tools for servicing.
1. Disconnect both the negative and positive battery terminal s, then wait at least three minutes. Refer to PG-
73, "Removal and Installation (Battery)".
2. Remove the steering column covers. Refer to IP-17, "Removal and Installation"
.
3. Rotate steering wheel clockwise to access first combination switch bolt and remove.
4. Rotate steering wheel counter-clockwise to access second combination switch bolt and remove.
5. Disconnect the harness connector from the combination switch and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag wa rning lamp, reset with the self-diagnosis function
and delete the memory with CONSULT.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to SRC-42, "ADDITIONAL SERVICE WHEN RE PLACING CONTROL UNIT : Special Repair
Requirement".
AWMIA1293ZZ
1. Combination switch 2. Combination switch harness connector Front
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BR-6
< SYSTEM DESCRIPTION >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYSTEM DESCRIPTION
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting ChartINFOID:0000000009463681
Use the chart below to help you find the cause of the sy mptom. If necessary, repair or replace these parts.
×: ApplicableReference page
BR-11, "BRAKE PAD : Inspection"
,
BR-12
BR-11
, BR-12
BR-11
, BR-12—
—
BR-11, "DISC ROTOR : Inspection", BR-12, "DISC ROTOR : Inspection"—
—
—
BR-11, "DISC ROTOR : Inspection", BR-12, "DISC ROTOR : Inspection"
PB-6, "Inspection"
FAX-5, "NVH Troubleshooting Chart"
, RAX-4, "NVH Troubleshooting Chart"
FSU-6, "NVH Troubleshooting Chart"
,RSU-4, "NVH Troubleshooting Chart"
FAX-5, "NVH Troubleshooting Chart"
(front axle), RAX-4, "NVH Troubleshooting Chart"
(rear axle)
WT-52, "NVH Troubleshooting Chart"
WT-52, "NVH Troubleshooting Chart"FAX-5, "NVH Troubleshooting Chart"ST-29, "NVH Troubleshooting Chart"
Possible cause and
SUSPECTED PARTS
Pads - damaged
Pads - uneven wear
Shims damaged
Rotor imbalance
Rotor damage
Rotor runout
Rotor deformation
Rotor deflection
Rotor rust
Rotor thickness variation
Drum out of round
WHEEL HUB
SUSPENSION
AXLE
TIRES
ROAD WHEEL
DRIVE SHAFT
STEERING
Symptom Noise
××× ××× ×××
××
Shake × ×× ×××
××
Shimmy, Shudder ×××××××× × ××× ×
Revision: November 20132014 Altima NAM

BR-18
< REMOVAL AND INSTALLATION >
BRAKE PEDAL
REMOVAL AND INSTALLATION
BRAKE PEDAL
Exploded ViewINFOID:0000000009463696
Removal and InstallationINFOID:0000000009463697
REMOVAL
1. Remove the instrument lower panel LH. Refer to IP-14, "Exploded View".
2. Remove the accelerator pedal. Refer to ACC-3, "Removal and Installation"
.
3. Disconnect the harness connectors from the stop lamp switch and ASCD cancel switch.
4. Remove the stop lamp switch and ASCD canc el switch from the brake pedal assembly.
5. Remove the snap pin (1) and clevis pin (2) from the brake pedal assembly.
CAUTION:
Do not reuse the snap pin or clevis pin.
6. Disconnect the brake booster clevis from the brake pedal assembly.
7. Disconnect the steering column assembly pinch bolt and position the steering column assembly aside to
gain access to the brake pedal assembly. Refer to ST-33, "Exploded View"
.
8. Remove the brake pedal assembly nuts. NOTE:
Remove the top brake pedal assembly nut first.
9. Remove the harness clips from the brake pedal assembly.
10. Remove the brake pedal assembly.
INSTALLATION
1. Snap pin 2. Brake pedal assembly 3. Brake pedal pad
4. Stop lamp switch 5. ASCD cancel switch 6. Clevis pin
AWFIA0931ZZ
JPFIA0019ZZ
Revision: November 20132014 Altima NAM

BRAKE PIPINGBR-21
< REMOVAL AND INSTALLATION >
C
D E
G H
I
J
K L
M A
B
BR
N
O P
FRONT : Hydraulic PipingINFOID:0000000009463699
Four Channel Hydraulic Circuit
CAUTION:
• All hoses and piping (tubes) must be fr ee from excessive bending, twisting and pulling.
• Make sure there is no interference with other pa rts when turning steering both clockwise and coun-
terclockwise.
• The brake piping is an important safety part. If a brake fluid leak is detected, always disassemble the
parts. Replace applicable part with a new one, if necessary.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Do not bend or twist brake hose sharply, or strongly pull it.
• Do not reuse drained brake fluid.
• After installation of the ABS actuator and electri c unit (control unit), refill brake system with new
brake fluid. Then bleed the ai r from the system. Refer to BR-14, "Bleeding Brake System"
.
FRONT : Removal and InstallationINFOID:0000000009463700
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
1. Remove the wheel and tire using power tool. Refer to WT-55, "Adjustment"
.
2. Drain brake fluid. Refer to BR-14, "Drain and Refill"
.
AWFIA0910ZZ
1. ABS actuator and electric unit
(control unit) 2. Master cylinder 3. Booster
4. Connector A. Union bolt B. Flare nut M12
C. Flare nut M10
Revision: November 20132014 Altima NAM

BR-22
< REMOVAL AND INSTALLATION >
BRAKE PIPING
3. Disconnect the brake hose (1) from brake tube (2) at the flarenut (A) using a suitable tool and remove the lock plate (3).
4. Remove the union bolt (A) and remove brake hose from caliper assembly. Discard the copper sealing washers.
• Protrusions (B)
CAUTION:
Do not reuse the copper sealing washers.
5. Remove the brake hose.
INSTALLATION
CAUTION:
• All brake hoses and brake tubes must be free fr om excessive bending, twisting and pulling.
• Make sure that there is no interference with othe r parts when turning steering both clockwise and
counterclockwise.
• Brake tubes and brake hoses are an important safety part. Always disassemble the parts and
retighten their fittings if a brake fluid leak is detect ed. Replace applicable part with a new one, if dam-
aged part is detected.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Refill with new brake fluid “DOT 3”.
• Do not reuse drained brake fluid.
1. Assemble the union bolt and new copper sealing washers on the brake hose. CAUTION:
Do not reuse the copper sealing washers.
2. Install brake hose by aligning the brake hose with the protrusion (B) on brake caliper assembly as shown. Tighten union bolt (A)
to the specified torque. Refer to BR-20, "FRONT : Exploded
View".
AWFIA0933ZZ
ALFIA0287ZZ
ALFIA0287ZZ
Revision: November 20132014 Altima NAM

BR-24
< REMOVAL AND INSTALLATION >
BRAKE PIPING
REAR : Hydraulic Piping
INFOID:0000000009463702
Four Channel Hydraulic Circuit
CAUTION:
• All hoses and piping (tubes) must be free from excessive bending, twisting and pulling.
• Make sure there is no interference with other part s when turning steering both clockwise and coun-
terclockwise.
• The brake piping is an important safety part. If a brake fluid leak is detected, always disassemble the
parts. Replace applicable part with a new one, if necessary.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Do not bend or twist brake hose sharply, or strongly pull it.
• Do not reuse drained brake fluid.
• After installation of the ABS actuator and electric unit (control unit), refill brake system with new
brake fluid. Then bleed the ai r from the system. Refer to BR-14, "Bleeding Brake System"
.
REAR : Removal and InstallationINFOID:0000000009463703
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove wheel and tire using power tool. Refer to WT-55, "Adjustment".
2. Drain brake fluid. Refer to BR-14, "Drain and Refill"
.
AWFIA0910ZZ
1. ABS actuator and electric unit
(control unit) 2. Master cylinder 3. Booster
4. Connector A. Union bolt B. Flare nut M12
C. Flare nut M10
Revision: November 20132014 Altima NAM