2014 MITSUBISHI OUTLANDER SPORT instrument cluster

Normal charging (charging method with rated AC 240 V outlet)
Charging 3-13
3
8. Make sure that the charging indicator (H)on the instrument cluster is illuminated.If the charging indicator is not illumi-nated, charging has not started.Make sure that the normal charge port andthe plug are correctly connected, and per-form charging from Step 5 again.
9. Charging is complete when the chargingindicator turns off. Pull out the normalcharge connector while pressing the but-ton (K).
10. Close the inner lid and press the rear of
the normal charging lid until it clicks toclose it.
11. Remove the charging cable plug from the
outlet.
IH
J
NOTE
zWhen the normal charge connector is con-nected to the charge port, the charging indi-cator will blink. When charging is started,the charging indicator is illuminated.zIf one of the doors is opened or the multi-information display switch is operated, thedrive battery level display (I) appears in themulti-information disp
lay and indicates the
drive battery level. In addition, when theremaining time is less than 1 hour, the pre-dicted charging time display (J) appears --:--and does not indicate a malfunction.
K
CAUTIONzBe sure to check the normal charge connec-tor is removed from the normal charge port.Since it will change into the state which canbe started the vehicle when the power switchis operated if the normal charge connectordoes not locked completely, resulting in anunexpected accident.NOTE
zCharging can be stopped half way. In thiscase, also, pull out the normal charge con-nector while pressing the button. Pressingthe manual stop button on the control boxcan also stop charging.Refer to “EV charging cable” on page 3-5.NOTE
zMake sure that the inner lid is completelyclosed.If the normal charging lid is forcibly closedwithout completely cl
osing inner lid, the
hinge on the inner lid may be broken.
BK0203201EN.book 13 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Information screen display
Instruments and controls 6-39
6
E00502702287
This warning lamp will illu-minate when there is a prob-lem with the charging systemfor the auxiliary battery.Normally, when the operation
mode of the power switch is put in ON, thiswarning lamp will illuminate. Then, when thePlug-in Hybrid EV System is started and theready indicator illuminates, the warning lampwill go out.
E00537300023
This warning lamp will illu-minate when there is a fault atthe Plug-in Hybrid EV Sys-tem.Refer to “Service precautions”
on page 11-2.Normally, this warning lamp illuminateswhen the operation mode of the power switchis put in ON, and goes off after a few seconds.
E00537200022
This warning lamp will illu-minate when there can notused at the regenerative brakewhile the Plug-in Hybrid EVSystem is operating.
The warning is also displayed on the multiinformation display.
Normally, this warning lamp illuminateswhen the operation mode of the power switchis put in ON, and goes off after the Plug-inHybrid EV System is activated.
E00524601117E00524701381
This warning is displayed if you drive withthe parking brake still applied. The warninglamp in the instrument cluster only illumi-nates when the parking brake is applied.
Auxiliary battery charge warn-ing lamp
CAUTIONzIf the warning lamp stays on after the readyindicator illuminates, there may be a prob-lem with the charging system for the auxil-iary battery.•Immediately park your vehicle in a safeplace and we recommend you to have itchecked.•Do not charge the auxiliary battery.
Plug-in Hybrid EV System warning lamp
CAUTIONzIf the lamp illuminates while the Plug-inHybrid EV System is
operating, immediately
park your vehicle in a safe place and we rec-ommend you to consult a MITSUBISHIMOTORS Authorised Service Point.
Regenerative brake warning lamp
CAUTIONzIf the lamp illuminates while the Plug-inHybrid EV System is
operating, we recom-
mend you to have the vehicle inspected by aMITSUBISHI MOTORS Authorised ServicePoint.
Information screen display Brake warning display
BK0203201EN.book 39 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Combination headlamps and dipper switch6-40 Instruments and controls
6
When the operation mode of the powerswitch is put in ON, if the brake fluid is low,this warning is displayed.The warning lamp in the instrument clusteralso illuminates.
E00524901309
If the engine oil pressure drops while thePlug-in Hybrid EV System is operating, the
warning display is displayed on the informa-tion screen in the multi information display.
E00506003416
CAUTIONzIf a vehicle is driven without releasing theparking brake, the brake will be overheated,resulting in ineffectiv
e braking and possible
brake failure.If this warning is displayed, release the park-ing brake.CAUTIONzIf this warning stays illuminated and doesnot go out while driving, there is a danger ofineffective braking. If this happens, immedi-ately park your vehicle in a safe place andwe recommend you to have it checked.
zIf the brake warning disp
lay is displayed and
the brake warning lamp and the ABS warn-ing lamp are illuminated at the same time,the braking force dist
ribution function will
not operate, so the vehicle may be destabi-lised during sudden braking. Avoid suddenbraking and high-speed driving, stop thevehicle in a safe place, and we recommendyou to have it checked.zThe vehicle should be brought to a halt in thefollowing manner when brake performancehas deteriorated.•Depress the brake pedal harder than usual.Even if the brake pe
dal moves down to the
very end of its possible stroke, keep itpressed down hard.• Should the brakes fail, use regenerativebrake to reduce your speed and carefullypull the parking brake lever.Depress the brake pedal to operate the stoplamp to alert the vehicles behind you.
Oil pressure warning display
CAUTION
CAUTIONzIf the vehicle is driven while the engine oil islow, or the oil level is normal but the warn-ing is displayed, the engine may burn out andbe damaged.zIf the warning is displayed while the Plug-inHybrid EV System is operating, immediatelypark your vehicle in a safe place and checkthe engine oil level.zIf the warning is disp
layed while the engine
oil level is normal, have it inspected.
Combination headlamps and dipper switch Headlamps
NOTE
zDo not leave the lights on for a long timewhile the Plug-in Hybrid EV System is sta-tionary (not operating). A run-down auxil-iary battery could result.
BK0203201EN.book 40 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Combination headlamps and dipper switch6-42 Instruments and controls
6
zIf the operation mode of the power switchis put in OFF or ACC while the lampswitch is in the “ ” or “ ” position,the lamps will turn off automaticallywhen the driver"s door is opened.zIf the operation mode of the power switchis put in OFF or ACC while the lampswitch is in the “ ” or “ ” position,the lamps will remain on for about 3 min-utes while the driver’s door is shut andwill then automatically turn off.
1. Turn the lamp switch in the “OFF” posi-tion while the operation mode of thepower switch is in OFF or ACC.2. Turn on the lamps with the switch in the“ ” or “ ” position again, then thelamps will remain on.3. When 1 minute has passed, the lamps willautomatically be turned off.
E00506101631
If the driver’s door is opened when the opera-tion mode of the power switch is put in ACCor OFF with the lamps illuminated, a buzzerwill sound to remind the driver to turn off thelamps.The buzzer will automatically stop if theauto-cutoff function is activated, the lampswitch is turned off, or the door is closed.
E00506201544
When the lamp switch is in the “ ” posi-tion, the beam changes from high to low (orlow to high) each time the lever is pulledfully (1). While the high beam is on, the highbeam indicator lamp in the instrument clusterwill also illuminate.
E00506300199
The high beams flash when the lever is pulledslightly (2), and will go off when it isreleased.When the high beam is on, the high beamindicator lamp in the instrument cluster willilluminate.
Lamps (headlamps, fog lamp, etc.) auto-cutout function
NOTE
zThe lamp auto-cutout function can also bedisabled.For further information, we recommend youto consult a MITSUBISHI MOTORSAuthorised Service Point.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.
When you want to keep the lamps on:
NOTE
zIf you place the light switch in the “ ”position, the lamps will not be automaticallyturned off.
Lamp monitor buzzer
Dipper (High/Low beam change) Headlamp flasher
BK0203201EN.book 42 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Turn-signal lever
Instruments and controls 6-45
6
E00506502645
E00506602024
Use the hazard warning flasher switch whenthe vehicle has to be parked on the road forany emergency.The hazard warning flashers can always beoperated, regardless of the operation mode.Push the switch to turn on the hazard warningflashers, all turn signal lamps flash continu-ously. To turn them off, push the switchagain.
Tu r n - s i g n a l l e v e r 1- Turn-signals
When making a normal turn, use position(1). The lever will return automaticallywhen cornering is completed.
2- Lane-change signals
When moving the lever to (2) slightly tochange a lane, the turn-signal lamps andindicator lamp in the instrument clusterwill only flash while the lever is oper-ated.Also, when you move the lever to (2)slightly then release it, the turn-signallamps and indicator lamp in the instru-ment cluster will flash three times.
NOTE
zIf the lamp flashes unusually quickly, thebulb in a turn-signal lamp may have burnedout. We recommend you to have the vehicleinspected.zIt is possible to activate the following func-tions:•Flashing of the turn-signal lamps when thelever is operated with the operation mode isin ACC.•Deactivate the turn-signal lamp 3-flashfunction for lane changes•The time required to operate the lever forthe 3-flash function can be adjusted.For further information, we recommend youto consult a MITSUBISHI MOTORSAuthorised Service Point.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.zIt is possible to change the tone of a sound-ing buzzer as the turn-signal lamps flash.Refer to “Changing the turn-signal sound”on page 6-20.
Hazard warning flasher switch
NOTE
zIf the switch is used for a long period whilethe ready indicator is not illuminated, theauxiliary battery coul
d go flat and the Plug-
in Hybrid EV System could be impossible tostart.
BK0203201EN.book 45 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

ECO mode switch6-46 Instruments and controls
6
E00531801049
ECO mode is an eco-driving support systemwhich automatically controls the Plug-inHybrid EV System and air conditioning sys-tem to improve fuel efficiency.Refer to “Automatic climate control air con-ditioner” on page 8-4.The ECO mode starts working by pressingthe ECO mode switch when operation modeof the power switch is in ON. Push the switchagain and the ECO mode will cancel.While the ECO mode is working, an ECOmode indicator will be turned on.
E00506700034E00508301741
The front fog lamps can be operated while theheadlamps or tail lamps are on. Turn the knobin the “ON” direction to turn on the front foglamps. An indicator lamp in the instrumentcluster will also come on. Turn the knob inthe “OFF” direction to turn off the front foglamps. The knob will automatically return toits original position when you release it.
zOn vehicles equipped with the emergencystop signal system, while the hazard warninglamps are blinking due to having manuallypushed the switch, the emergency stop signalsystem does not operate.Refer to “Emergency stop signal system” onpage 7-29.
ECO mode switch
NOTE
NOTE
zEven if the ECO mode is operating, you canselect normal operation of the air condi-tioner.For further informati
on, we recommend you
to consult a MITSUBISHI MOTORSAuthorised Service Point.On vehicles equipped
with Mitsubishi Multi-
communication System (MMCS), it is possi-ble to change the setting by means of screenoperations.Refer to the separate owner’s manual fordetails.
Fog lamp switch Front fog lamp switch LHD/RHD (Type 1)
BK0203201EN.book 46 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Wiper and washer switch
Instruments and controls 6-47
6
E00508401612
The rear fog lamp can be operated when theheadlamps or front fog lamps turn on.An indicator lamp in the instrument clustercomes on when the rear fog lamp is turnedon.
Turn the knob once in the “ON” direction toturn on the front fog lamps. Turn the knobonce more in the “ON” direction to turn onthe rear fog lamp. To turn the rear fog lampoff, turn the knob once in the “OFF” direc-tion. Turn the knob once more in the “OFF”direction to turn off the front fog lamps. Theknob will automatically return to its originalposition when you release it.
E00507101218E00516901687
The windscreen wipers can be operated withthe operation mode of the power switch inON or ACC.If the blades are frozen to the windscreen orrear window, do not operate the wipers until
NOTE
zThe front fog lamps are automatically turnedoff when the headlamps or tail lamps areturned off. To turn the front fog lamps onagain, turn the knob in
the “ON” direction
after turning on the headlamps or tail lamps.zDo not use fog lamps except in conditions offog, otherwise excessi
ve lamp glare may
temporarily blind oncoming vehicle drivers.
Rear fog lamp switch
*
RHD (Type 2)
NOTE
zThe rear fog lamp is automatically turned offwhen the headlamps or front fog lamps areturned off.zTo t u r n t h e r e a r f o g l a m p o n a g a i n , t u r n t h eknob twice in the “ON” direction after turn-ing on the headlamps.
Wiper and washer switch
CAUTIONzIf the washer is used in cold weather, thewasher fluid sprayed against the glass mayfreeze, which may hinder visibility. Warmthe glass with the de
froster or rear window
demister before using the washer.
Windscreen wipers
NOTE
zTo e n s u r e a c l e a r r e a r w a r d v i e w, t h e r e a rwindow wiper will automatically performseveral continuous
operations if the selector
lever is put in the “R” position while thewindscreen wipers are operating. Refer to “Rear window wiper and washer”on page 6-51.
Except for vehicles equipped with rain sensor
BK0203201EN.book 47 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Emergency stop signal system*
Starting and driving 7-29
7
E00626001073
This is a device that reduces the possibility ofrear end collisions by the rapid and automaticblinking of the hazard warning lamps to alertvehicles approaching from behind duringsudden braking. When the emergency stopsignal system operates, the hazard warningindicator lamp in the instrument clusterblinks rapidly at the same time.
E00607102489
Environmental conditions can have an effecton braking. During sudden braking whenthere is snow, ice, oil, water etc. on the roadsurface, a skid may occur. In this situation,steering control and braking effectiveness isreduced and the stopping distance isincreased. The vehicle may also go into anuncontrolled spin.The ABS helps prevent the wheels from lock-ing during braking, thus maintaining direc-
tional stability, ensuring controllability andproviding optimum braking force.zAlways maintain the same distance fromthe vehicle in front of you as you wouldfor a vehicle not equipped with ABS.Compared with vehicles not fitted withABS, your vehicle may require a longerstopping distance in the following cases:•Driving on gravel or snow-coveredroads.• Driving with snow traction device (tyrechains) installed.•Driving on roads where the road surfaceis pitted or has other differences in sur-face height.• Driving on bumpy roads or other poordriving surfaces.
zOperation of ABS is not restricted to situ-ations where brakes are applied suddenly.This system may also operate to preventwheel lock when you are driving overmanholes, steel road-work plates, or thevehicle is driven over steps or level differ-ences in the road, road markings, or othersurfaces which are difficult for the wheelsto grip.
Emergency stop signal sys-tem
*CAUTIONzIf the ABS warning or ASC warning is dis-played, the emergency stop signal systemmay not operate. Refer to “ABS warninglamp/display” on page 7-30.Refer to “ASC warn
ing display” on page
7-34.NOTE
z[Activating condition for the emergency stopsignal system]It activates when all
of the following condi-
tions are met.•The vehicle speed is approximately 55km/h or higher.
•The brake pedal has been depressed, andthe system judges that it was sudden brak-ing from the vehicle deceleration and theoperating condition of the anti-lock brakesystem (ABS).[Deactivating condition for the emergencystop signal system]It deactivates when one of the following con-ditions is met.•The brake pedal is released.• The hazard warning flasher switch ispressed.•The system judges that it was not suddenbraking from the vehicle deceleration andthe operating condition of the anti-lockbrake system (ABS).
Anti-lock brake system (ABS)
NOTE
Operating hints
BK0203201EN.book 29 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分