2014 AUDI TT ROADSTER Owners Manual

the distance between your vehicle and
other vehicles.
- For safety reasons, the cruise control
should not be used in the city, in stop­
and-go traffic, on twisting roads and
when road conditions are poor (such as
ice, fog, grave l, heavy rain and hydro­
planing) -risk of acc ident.
- Turn off the cruise control temporari ly
when entering turn lanes, highway exit
lanes or in const ruction zones.
- Please note that inadvertent ly "rest ing"
yo ur foot on the accelerato r peda l causes
the cruise control not to brake. This is
because t he cr uise con trol is overr idden
by the driver's acce le rat ion.
@ Tips
The cruise control cannot mai nta in a con­
stant speed when driving downhill. The ve­
hicle will acce lerate unde r its own weight.
Downshift to a lower gear or use t he
bra kes to slow down.
Changing speed
~ Press lever in the 0 or O direction
Q page 78, fig. 86 to increase or decrease
your speed.
~ Release the lever to save that speed.
You can a lso press the accelerator peda l down
to increase your speed, e.g. if you want to
pass someone. The speed you saved earlier
will resume as soon as you release the acceler­
ator peda l.
If, however, you exceed your saved speed by
5 mph (10 km/h) for longer than 5 minutes,
the cruise contro l will turn off tempora rily.
The symbol will go out but the saved speed
will be retained.
Presetting your speed
You can preset your desired speed while the
vehicle is not moving .
~ Turn on the ignition.
On the ro ad 79
~ Pull leve r into position (D q page 78,
fig. 86 .
~ Press the leve r in the 0 or O direction to
increase or decrease your speed.
~ Release the lever to save that speed.
T his function makes it possib le, for examp le,
to save the speed you want before dr iving on
the highway. Once on the highway, activate
the cruise control by pulling the lever toward
(D .
Switching the system off
Temporary deactivation
~ Press the brake pedal, or
~ Press the leve r into position @(not clicked
into place)
q page 78, fig . 86, or
~ Dr ive fo r longer than 5 m inutes a t more
t han 5 mph (10 km/h) above the stored
speed .
Switching off completely
~ Press lever into position @ (clicked into
place), or
~ Switch the ignit ion off.
The system retains the saved speed if you de­ activate the c ruise control temporar ily. To re­
s u me the saved speed, re lease the brake ped­
al a nd pull th e leve r to pos it ion
(D .
Switching the ignit ion off erases the saved
speed.
.&_ WARNING
You shou ld only ret urn to the saved speed
if it is no t too fast for the c urre nt traffic
conditions -risk o f an accident!

80 On the road
Audi magnetic ride
Applies to vehicles: with magnetic ride
Damping can be adjusted to the driver's pref­
erence and it adapts automatically to the cur­
rent driving situation.
Fig. 88 Center console: Switch for Audi magnetic r ide
.,. Press the sw itch ~ fig. 88 to turn sport set-
ting on or off.
Aud i magnetic ride is an electronically con­
trolled damping system. This chassis system
assists the driver by adapting to the particular
situation through imperceptible control proc­
esses. The
damping provides individual modu­
lation of damping forces. For example, with
damping characteristics set to provide greater
comfort, damping is set somewhat harder for
a brief period only as required, when rounding
a curve and when braking.
Standard setting
Select the standard setting if you prefer a sus­
pension setting emphasizing comfort.
Sport setting
Select the sport setting if you prefer a sporty
suspe nsion setting . The LED in the switch
8
comes on to indicate sport setting.
@ Tips
The warning/indicator light 8 in the instru­
ment cluster comes on in the event of a
malfunction .
Drive to the closest author­
ized Audi dealer as soon as possible and
have the malfunction repaired.
Sport mode
Applies to vehicles: with Sport button
Fig. 89 Button in the center console
.,. To switch sport mode on, press the button
in the center console. The indicator light
turns on .
.,. To switch sport mode off, press the button
in the center console again. The indicator
light turns on .
A more agile and sporty driving style is possi­
ble when driving the vehicle in "sport mode".
T his mode affects throttle response and the
sound of the engine and the damping charac ­
teristics of the Audi magnetic ride for dynamic
suspension tuning .
@ Tips
If there is a malfunction in the retractable
rear spoiler* or the Audi magnetic ride*, it
may not be poss ible to activate sport
mode.
Acoustic parking system
Rear acoustic park assist
Applies to vehicles: with 4-channel acoustic park assist
Acoustic park assist gives a warning about
obstacles behind the vehicle.
Description
T he rear acoustic park ass ist (4-channel
acoustic park assist) determines the distance
of the vehicle from an obstacle using ultra­
son ic sensors. The sensors are in the rear
bumper. The volume and the pitch of the

chimes can be adjusted through the menu dis­play ~
page 24.
The range at which the sensors start to meas­
ure is
about :
To the side 2 feet (0.60 m)
Center rear
5 feet (1.60 m)
Activation
The parking assist is activated when reverse
gear
is engaged. A brief tone confirms that
the system is activated .
Backing up
Distance warning when backing up starts
when an obstacle is detected in the range of
the park assist system. As the distance de­
creases, the time interval between the audible
tones becomes shorter.
When the distance is less than 1 foot (0 .30
m), the tone becomes continuous . At this
point you should stop backing up.
Please note that low objects already signalled
by a warning can disappear from the system's
detection range and will not continue to be
signalled.
Potential malfunctions
If a war ning buzzer sounds for a few seconds
when the ignition is switched on, there is a
system malfunction with the acoustic park as­
sist . If the malfunction persists until the igni­
tion is switched off, there will be no acoustic
warning at the next attempt to activate the
system. Have the problem corrected.
There is no confirmation tone when reverse
gear is engaged if there is a system malfunc­
tion .
For the parking assist to operate, the sensors
must be kept clean and free of ice .
.8, WARNING
- Sensors have blind spots in which objects
cannot be detected . Pay special attention
to small children and animals. They can-
On the road 81
not always be detected by the sensors -
danger of an accident!
- The parking assist cannot replace the
driver's attention. The driver alone is re­
sponsible for parking and similar driving
maneuvers. Always watch where you are
driving .
(D Note
Low obstacles already signalled by a warn­
ing can disappear from the system's detec­
tion range as they are approached and will
not continue to be signalled. Objects such
as barrier chains, trailer draw bars, thin painted vertical poles, or fences may not
be detected by the system -risk of dam­
age.
(D Tips
For the parking assist to operate, the sen­
sors must be kept clean and free of snow
and ice.

82 Transmi ssion
Transmission
S tronic transmission
Introduction
App lies to vehicles : wit h S tro nic
Your veh icle is equipped with a S tronic trans­
miss ion, a lso called a double-clutch system/
tra nsmission.
Power is transfe rred between the engine and
the transm ission by means of two i ndepend­
ent cl utches. They replace the to rque conve rt­
e r of conventional a utomat ic transm iss io ns
and a llow the vehicle to acce le rate w it h out a
noticeab le break in the power flow .
W ith the aid oftiptroni c, the gea rs can op ­
tionally be sh ifted
manually ¢ page 85.
Selector lever positions
App lies to vehicles: wit h S tro nic
All the selector lever positions are explained
in this section.
l-- -·· -----,,1
+55°F
~ 340mi
D
F ig. 90 Display: Selector lever posit ion
The instrument cluster display shows these ­
l ector lever posit ion.
P - Park lock
I n th is posi tion the ge ars are mechan ically
l ocked .
The park lock must on ly be engaged with t he
ve hicl e
stationary ¢&, .
To engage P and to remove the lever from th is
position, you must depress the release button
(button in the selector leve r hand le)
and si­
multaneous ly yo u m ust s tep on the brake
pedal.
R -reverse
In this pos ition, reverse is eng aged .
Reve rse gear m ust only be e ngaged w ith the
vehicle
stationary and the engine ru nning at
idle speed ¢ &, .
T o engage R, you have to depress the release
button
and simultaneously step on the b rake
peda l. In the R pos ition, the bac k-up lights il­
l u minate w ith the igni tion o n.
N - Neutral
The transm iss ion is in neut ral i n this pos ition.
D -No rmal position fo r driving forward
In this position, the forward gears are auto­
matically shifted up and down, depending on
engine load and vehicle speed.
T o engage D from
N, the brake pedal m ust be
depressed at s peeds below 5 km/h or when
the ve hicle is stationary ¢& .
In cert ain circ umstan ces (driving in the moun­
ta ins for examp le) it can be beneficia l to
switch temporari ly to the man ual shift pro ­
gram ¢
page 85 in order to ad just the gear
ratios to driving conditions
manually .
S -Sport setting
T he S setting sho uld be se lec ted for sporty
driving. The power reserves of the engine can
be fully explo ited through later upshifts.
T o engage S from N, t he brake peda l m ust be
depressed at speeds below 5 km/h o r when
t h e vehi cle is stationary ¢& .
A. WARNING
- Never p lace the se lector lever i n the R or
P posit ion while the veh icle is moving -
risk of an accident!
- W ith the engine r unning, it is necessary
to hold the vehicle with the foot brake in
all se lector lever positions (except P and
N), because even at idle speed the trans­
fe r of power is never completely inter­
r u pted - t he vehicle "creeps". If t he vehi-
cle is stat io nary and the t rans missio n is
~

engaged, the engine should never be
speeded up unintentionally (e.g. manual­ ly from under the hood). Otherwise the
vehicle will immediately start to move -
sometimes even if the parking brake is
firmly applied - risk of an accident!
- Before you or other persons open the
hood and work on a running engine, the
selector lever must be moved to P and
the parking brake applied firmly - risk of
an accident! Follow the warning stickers.
@ Tips
If you have inadvertently sh ifted into N
while the veh icle is moving, you should re­
move your foo t from the accelerator and
wait until the engi ne speed has dropped to
id le before shifting back to Dor S.
Selector lever lock
Applies to vehicles: with S tro nic
The selector lever lock prevents a gear from
being engaged occidentally and unintention­
ally setting the vehicle in motion .
Fig. 91 Selector lever locks
The selector lever lock is released as follows:
.,. Switch the ignition on.
.,. Step on the brake pedal
and simultaneously
hold down the re lease button.
Automatic selector lever lock
The selector lever is locked in the P and N po­
sitions when the ignition is on. To move the
l ever from these positions the driver must de­
press the brake pedal. As a reminder to the
driver, the following warning appears in the
Transmission 83
instrument cluster display when the se lector
is in P and N:
To start engine or select gear apply foot
brake when stationary
The selector lever lock is effective only when
the vehi cle is stationary and a t speeds below
S km/h . At higher speeds, the lock in the N
pos ition is automat ically switched off.
The selector lever is not locked when rapid
shifts are made through the N position (e.g.
from R to D) . This allows you to "rock " the ve­
hicle if it becomes stuck. If the lever is in the
N position for more than 1 second with the
brake pedal not depressed, the selector lock
engages automatically .
Release button
The release butto n in the selector lever han­
dle prevents accidental shifts into certain se­
lector lever positions . When you press the re­
lease button , the selector lever lock is cancel­
led. In the illustration, the positions in which
the release button has to be pressed are high­
lighted in color
¢ fig . 91.
Ignition key removal lock
The ignition key can only be removed after the
ignition is switched off if the selector lever is
in P. As long as the ignition key is removed,
the selector lever is locked in P.
(y Tips
If the se lector lever does not engage,
there is a malfunction . The engine is disa­
bled to prevent th e vehicle from driving off
unintentionally. To allow the selector lever
to engage again, proceed as follows: Press
and release the brake pedal.

84 Transmi ssion
Driving Notes
Appl ies to vehicles: with S tron ic
The forward gears are shifted up or down au­
tomatically.
--
-
-
-
-
-
--Fig. 92 Section from ce nter console: Se lector leve r
wit h release b utto n
Starting the engin e
• The selector lever must be in the P or the N
posit ion. At low temperatures (be low -10
0
(), the engine can only be started when the
selector lever is in the P position .
Starting f rom sto p
.. Step on and hold the brake pedal.
• Hold the re lease button (button in se lector
lever) down, move the selector lever to the
desired position, for example Do
page 82,
and release the button.
• Re lease the brake pedal and acce lerate
o .&_ .
Stopp ing tem pora rily
• Bring the vehicle to a full stop with the
brake, e.g . at traffic signals .
• Do not accelerate .
Pa rkin g
.. Step on and hold the brake peda l o A .
• Apply the parking brake firmly .
• Hold the release button down, move these­
lector lever to P and release the button .
Stopping on an incline
• Always hold the vehicle with the footbrake
or parking brake in order to prevent "roll­
back" o
,&. Do not try to prevent the vehi­
cle from rolling back by revving the engine
while it is in gear .
Starting on a hill
• Apply the hand brake firmly .
• With the engine in gear, gradually acceler-
ate and release the hand brake.
T he eng ine can only be
s tar ted w ith the selec­
tor leve r in P or No
page 74 . At low amb ient
temperatures (14
° F /-10 °C), it is only possi­
ble to start the engine with the selector lever
in P.
When parking o n level ground, it is s ufficient
to place the selector lever in P . On a steeply
s loping road, you shou ld first apply the park­
ing brake f irmly and then place the selector
lever in P. Th is way, you do not overload the
pawl mechanism and it is easier to move the
selector lever out of P .
A WARNING
- Never leave your vehicle with the engine
running while in gear . If you must leave
your veh icle w ith the engine r unning, set
the park ing brake and engage the park
lock .
- When the engine is running and the transmiss ion is in gear (D, Sor R) or in
"t iptronic" mode, it is essential that you
stop the vehicle with the footbrake.
When idling, the transmission of power does not stop comp letely -the vehicle
"creeps".
- Do not accelerate when you change the
selector lever position w it h the vehicle
stationary and the engine runn ing -risk
of an acc ident!
- Never p lace the selector lever in the R or
N pos ition wh ile the vehicle is mov ing -
risk of an acc ident!
- If you have to bring your vehicle to a stop
while on an incline, keep the foot brake depressed all the way down so that the
veh icle does not start to rol l backward.
You shou ld never ho ld the vehicle using
the clutch if you are going to be s topped
on an incline. If you do, the cl utch w ill
start to slip when it overheats ca used by
the constant overload. This is dangerous
~

because if the vehicle starts to roll
backward, you could cause an accident. If
the clutch should start to slip, you will
feel the vehicle "jerk" and the selector lever display will start blink ing.
- Before driving down a steep slope, re­
duce your speed and shift into a lower gear with "tiptronic".
- Do not ride the brakes or apply the brake
pedal too often or too long . Constant
braking causes the brakes to overheat
and substantially reduces braking per­
formance, increases braking distance or
causes complete failure of the brake sys­
tem.
Hill Descent Assist
Applies to vehicles: with S tro nic
Hill Descent Assist helps the driver when driv ­
ing down inclines .
Hill Descent Ass ist is activated by pressing the
b rake wh ile descending when the selector lev­
er is in D/S. The S tronic transmission auto­
mat ically shifts down to a gear suitab le for
the incline. Hill Descent Assist attempts to
maintain the current vehicle speed when the
brak ing occurs, as far as phys ical and techni ­
cal limits allow. It may be necessary to adjust
the speed using the brakes.
Hill Descent Assist switches off when the in­
cline levels out or when the gas pedal is press­
ed.
On vehicles w ith cruise control*~
page 78,
Hill Descent Assist is also activated when the
speed is set.
_&. WARNING
Hill Descent Assist cannot overcome phys i­
cal limitations, so it may not be possible to
ma intain a constant vehicle speed under
all circumstances . Always be ready to ap­
ply the brakes .
Transmission 85
tiptronic operation
Applies to vehicles: with S tronic
Tiptronic allows the driver to shift gears man­
ually.
Fig. 93 Center console: Ma nua l sh ift in g (t iptronic)
Fig . 94 D isplay : Manual sh ift ing (t iptron ic)
Switching to manual
"' Move the selector lever to the right out of
the D position . Th e display changes once the
transmission has switched to manual mode.
For examp le,
M4 indicates that 4th gear is
engaged.
Upshifting
"' Tap the selector lever forward (in the tip­
tronic setting)
~ fig. 93 0 -
Downshifting
"'Tap the selector lever backward (in the tip-
tronic setting)
0 -
Switching to manual can be carried out with
the vehicle stationary as well as moving .
When accelerating, the transmission shifts in­
to the next gear in gears 1, 2, 3, 4 and S
shortly before the maximum permissible en- gine speed is reached . ..,.

86 Transmis sion
If you have selected a lower gear than the cur­
rent one, the transmission w ill only shift down
when the engine cannot be overspeeded.
I f kick-down is actuated, the transmiss ion
shifts into a lower gear independently of
speed and engine rpm .
Steering wheel with Tiptronic controls
Applies to vehicles: with S tro nic
The selector paddles allow the driver to keep
both hands on the steering wheel when shift­
ing gears.
Fig. 95 Spo rt stee ring wheel w ith selecto r paddle s
Shifting up
.,. Pull the right paddle, marked 0 ¢ fig. 95
briefly towards you .
Shifting down
.,. Pull the left paddle, marked O ¢ fig. 95
briefly towards you .
The selector paddles on the steering wheel
are activated when the selector lever on the
center console is in D, 5 or in the manual posi­
tion ( Tiptronic mode).
You can also shift gears in the Tiptronic mode
using the selector lever on the center console.
(D Tips
With the gear selector lever in either Dor
5 the transmission will switch back to the
automatic mode if you do not use the pad­
dles within approx . 30 seconds.
Kick-down feature
Applies to vehicles: w it h S tronic
The kick-down feature allows maximum ac­
celeration.
If you depress the accelerator pedal fully be­
yond the full-throttle position, the transmis·
sion automatically downshifts one gear, de·
pending on vehicle speed and eng ine rpm. The
upshift into the next higher gear takes place
as soon as the maximum specified engine
speed is reached.
.&_ WARNING i-==
Please note that the drive wheels can spin
if the kick-down is used on a smooth slip·
pery road -risk of skidding!
Launch Control Program
Applies to veh icles: w it h S t ronic
The Launch Control Program permits maxi­
mum acceleration.
In order to use Launch Control, the ASR (Anti­
S lip Regulation) must be disabled . When ASR
is disabled , the ESC warning/indicator light
fl
in the instrument cluster illuminates. So that
Launch Control can be used, the engine must
be at operating temperature and the steering
wheel must not be turned.
.,. With the engine running, briefly press the
ESC button . The message "Stabilization pro­
gram off" or "Sport control Warning! Re­
stricted stability" in the driver information
system display .
.,. Shift the gear lever to "5" or the tiptronic
position .
.,. Step on the brake pedal with your left foot
and keep the brake pedal fully depressed for
at least one second.
.,. With yo ur right foot, step on the accelerator
to the wide-open throttle position or Kick·
down. The eng ine speed settles at about
3,200 rpm .
.,. Take your left foot off the brake. ..,.