2014 AUDI S4 wheel

Refitting
• Place th e caps over the wheel bo lts and
push th em back on.
The caps are to protect and keep the wheel bolts clean.
Loosening and tightening the wheel
bolts
The wheel bolts must be loosened before ra is­
ing th e vehicle .
Fig. 20 2 Changin g a w hee l: l oosening t he w heel bolts
Loo sening
• In stall the w heel bolt wrench over the
wheel bolt and push it down as far as it will
go .
• Take tight hold of the
end of the wrench
handle and turn the whee l bolts
co unter­
cl ock wise
about one single turn in the direc­
t ion of arrow
9 fig. 202 .
Tightening
• Install the whe el b olt wrench over the
wheel bolt and push it down as far as it will
go .
• Take tight hold of the
end of the wrench
hand le and turn each wheel bol t
clockwi se
until it is seated .
_& WARNING
-Do not use force or hurry when changing
a whee l -you can cause the vehicle to slip
off the jack and cause serious persona l
injuries.
- Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. -You risk an injury .
What do I do now ? 257
@ Tips
-Never use the hexagona l socket in the
hand le of the screwdr iver to loosen or
tighten the wheel bolts.
- If a wheel bo lt is very tight, you may find
it eas ier to loosen by carefully pushing
down on the end of the wheel bolt
wrench with
one foot only . As you do so,
hold o n to the car to keep your balance
and take care not to slip .
Raising the vehicle
The vehicle must be lifted with the jack first
before the wheel can be removed .
Fig . 203 Sill panels: mark ings
Fig. 20 4 Sill: positi on ing the v eh icle ja ck
The location of the jack po int is indicated by
an indentation on the underside of the vehicle
9 fig . 203 .
• Activate the parking brake to p rev ent the
veh icle from rolling unintentionally .
• Shift into
1st gear o n veh icles with m anual
transmiss ion or move the selector lever to
the P position on vehicles w ith automatic
transm iss ion .
• Find the
marking (imprint) on the sill that is
nearest the wheel that will be changed .,..

2 58 What do I do n ow ?
c:> fig. 203 . Behind the marking, there is a
lifting p oint on the sill for the veh icle jack.
• Turn the
veh icle j ack located under the lift­
ing point on the si ll to raise the jack until
the jaw
c:> fig. 204 ® covers the notch on
the vehicle
c:> &_ c:>(D .
• Align t he vehicle jack so the jaw ® covers
the notch and the base plate @ is flat on
the floor. The base plate @ must be
vertical
under the lifti ng point @.
• Install the rod on the vehicle jack: Insert the
rod into the opening on the handwheel. Turn
the rod left or right to secure it .
• Contin ue raising the jack with the rod until
the wheel lifts off the ground slightly.
Position the vehicle jack
onl y under the desig­
nated lifting points on the sill
c:> fig. 203 .
There is exactly one location for each wheel.
The jack must not be positioned at any other location
c:> ,&. c:>(D .
Soft ground under the jack can cause the ve­
hicle to slip off the jack. Always place the jack
on firm ground. Use a flat, stable support if necessary . Use a non-slip surface such as a
rubber mat on a
slipp ery surfac e such as tile .
A WARNING
-You or your passengers could be injured
wh ile chang ing a wheel if you do not fol­
low these safety precautions :
- Position the vehicle jack only at the
des ignated lifting points and align the
jack. Otherwise, the vehicle jack could slip and cause an injury if it does not
have sufficient hold on the veh icle .
- A soft or unstable surface under the
jack may cause the veh icle to slip off
the jack . A lways provide a firm base for
the jack on the ground.
If necessary,
use a sturdy board under the jac k.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to preven t
the jack from s lipping.
- T o help p revent injury to yourself and
yo ur passengers: -
Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the veh icle and
well away from the road and traffic .
- Make sure jack pos ition is correct, ad­
j ust as necessary and then cont inue to
raise the jack.
(D Note
Do not lift the vehicle by the sill. Position
the veh icle jack only at the designated lift­
i ng points on the sill. Otherwise, your vehi­
cle will be damaged.
Taking the wheel off/installing the spare
tire
Follow these instructions step-by-step for
changing the wheel .
Fig. 205 C ha nging a w hee l: us ing t he screwd rive r han ­
dle (w it h th e blade re m oved) to turn the bolts
Fig . 206 Ch ang ing a w hee l: alignment p in in side t he
top hole
After you have loosened all wheel bo lts and
raised the vehicle off the g round, remove and
replace the wheel as follows: .,..

Removing the wheel
"' Remove the topmos t wheel bolt completely
with the
he xagonal socket in t he screwdriv ­
er hand le (vehicle tool kit)
c::> fig. 205 and
set it aside on a
clean surface.
"' Screw the threaded end of the
alignment
pin
from the tool k it hand-tight into the
empty bolt hole
c::> fig. 206.
"'T hen remove the other wheel bo lts as de­
scribed above .
"'T ake off the wheel leav ing the alig nment pin
i n t he bolt hole
c::> CJ).
Putting on the spare tire
"' allroad : Inflate the inflatable spare tire
c::> page 254
"' Push the spare tire over the a lignment pin.
"' Screw o n the w heel bolts and tighten them
slightly using the hexagonal socket.
"' Remove the alignment pin and insert and
t ighten the remaining whee l bo lt s light ly
Li ke the rest.
"' Turn the jack handle counter-clockw ise to
lower the vehicle unt il the jack is f ully re­
l eased .
"' Use the wheel bolt w rench to t ighten all
whee l bolts firmly
c::> page 25 7. Tig hten
them
in a crisscross pattern, from one bo lt
to the (approx imately) opposi te o ne, to keep
t h e whee l cen te red.
"'P erfo rm the steps req uired after changing
t h e whee l
c::> page 256, After changing a
wheel .
The hex agonal so cket m akes it easier to re­
move the w heel bo lts from the r im . Care
should be taken when removing the reversible
b lade .
@ Note
When removing or ins tal ling the wheel,
the rim could hit the brake rotor and dam­
age the rotor . Wor k carefully and have a
second person to he lp you.
@ Tips
- When mounting tires with unidirectional
tread design
ma ke s ure the tread pat-
What do I do now? 259
'
tern is po inted the righ t way
c::>page 259.
- The w heel bolts shou ld be clean an d easy
to t urn . Check fo r dirt an d corrosion on
the mating surfaces of both the w heel
and the hub. Remove all d irt from these
surfaces before remounting the whee l.
- Do not use the hexagonal socket in the
sc rewd river handle to loosen or t ighten
the whee l bolts.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in
the right direction.
U si ng a spa re tire with a tread pattern
intended for use in a specific di rection
When using a spare t ire with a tread patter n
intended for use in a spec ific d irection, please
note the following :
- The d irect ion of rotation is marked by an
ar­
row on the side of the t ire .
-If the spare tire has to be insta lled in the in­
correct d irect ion, use the spare tire only
temporarily s ince the tire will not be able to
achieve its optimum performance cha racte r­
istics w it h regard to aquap la ni ng, no ise and
wear .
- We recommend that you pay part icu lar at­
t en tion to th is fact during wet weather and
that you adjust your speed to match road
condi tions.
- Replace the flat t ire wi th a new one a nd
have it insta lled o n you r vehicle as soo n as
pos sible to res to re the hand ling advant ages
o f a u nidirec tional tire.
Notes on wheel changing
Please read t he info rmation c::> page 242 , New
tires and replacing tires and wheels
if yo u a re
going to use a spare tire wh ich is different
from the tires on your vehicle.
After yo u change a tire:
IJI,-
•
•

260 What do I do now?
-Check the tire pressure on the spare imme­
diately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as possible by your authorized Audi dealer or
qualified workshop.
- With steel and alloy wheel rims , the wheel
bolts are correctly tightened at a torque of
90 ft lbs . (120 Nm).
- If you notice that the wheel bolts are cor­
roded and difficult to turn while changing
a tire, they should be replaced before you
check the tightening torque .
- Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover.
Until then, drive with extra care and at re ­
duced speeds .
A WARNING
-If you are going to equip y our veh icle
with t ires or rims w hich diffe r from t hose
w hich w ere facto ry ins talled, th en be
s ure to read the in for mati on ~
pag e 242,
N ew tir es a nd replacing tires and
wheel s.
- Always make su re the damaged w heel or
eve n a fla t tire and the ja ck and to ol kit
a re prop erly secure d in the lug gage com­
par tment and are not loose in the pas ­
senger com partment .
- In an a cciden t or sud den m ane uver they
cou ld fly forwar d, inju ring anyone in the
vehicle.
- Always s tore d amage d w hee l, ja ck a nd
tool s secure ly in the lu g gage com part ­
me nt. Otherw ise, in an acc ident or sud­
den maneuver they cou ld fly fo rward,
causing injury to passenge rs in the veh i­
cle .
@ Note
Do not use commerc ia lly available t ire
sea lants. Othe rwise, the elect rical compo­
ne nts of the tire pressure mon itor ing sys­
tem* will no longer wo rk p roperly and the
sensor for th e tire p ressur e monito rin g system
* wi ll h ave to be repla ced by qu ali­
fied workshop .

Front towing loop
Do not install the front towing loop until it is
needed.
ou
Fig . 2 13 Fr ont bumper : removing t he cover cap
ou
Fi g. 21 4 Front bumper: screwing in the towing loop
The tow ing loop fits into the th readed hole lo­
cated on the r igh t side of the fron t bumper
and covered by a small cover when not in use .
"' Remove the towing loop from the vehi cle
toolkit
c:::> page 252 .
"' Press the cover in by applying short strong
pressure to the bottom part to re lease it
from the bumper
c:::> fig. 213 .
"'Screw the towing loop tight ly into the
threaded hole as far as it will go
c:::> fig. 214
and tighten it w ith the wheel wrench .
When it is no longer needed, unscrew the
towing loop and put it back into the veh icle
toolkit. Be sure to have the towing loop stored
in the vehicle at all times.
A WARNING
If the towing loop is not screwed in as far
as it w ill go, the thread can pull o ut when
the vehicle is towed - potential risk of an
accident.
-
Emergenc y situ ation s 269
Rear towing loop
Do not install the rear towing loop until it is
needed .
Fig . 215 Rea r bu mper: cover
Fig. 216 Rea r bumpe r: Screwing in tow ing loop
"' "' N N
"' CD CD
On the right s ide of the rear bumper there is a
th readed hole for the towing loop. The
threaded hole is protected by a cover.
"' Remove the towing loop from the vehicle
too lki t
c:::> page 252.
"' Press the cover in by app lying shor t strong
pressure to the bottom part to release it
from the bumper
c:::>fig. 215.
"' Screw the towing loop tightly in to the
threaded ho le as far as it wi ll go
c:::> fig. 216
and tighten it with the wheel wrench.
Unscrew the towing loop again after use and
install the cover in the bumper. Install the
cover in the bumper. Return the towing loop
to the toolkit. Be sure to have the towing loop
stored in the vehicle at all times .
A WARNING
-
If the towing loop is not screwed in as far
as it will go, the thread can pull out when
the vehicle is towed - potent ia l ris k of an
a ccide nt.

2 76 Con sum er Inf ormation
comp lexity of today's automobi les, have
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Also, s afety an d e nvir onm ent al con­
cerns place very strict limits on the nature of repairs and adjustments to engine and trans ­
miss ion pa rts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth­
er equipment avai lab le to specially trained
workshop personnel in order to assure proper
performance, reliab ility and safety of the vehi­
cle and its many systems .
Improper ma intenance, adjustments and re ­
pa irs can impair the operation and reliab ility
of your vehicle and even void your vehicle war­ ranty. Therefo re , proof of servici ng in accord­
ance w it h the ma intenance sched ule may be a
condition for upholding a possible warranty
claim made within the warran ty period.
Above all, operational safety can be adve rsely
affected, c reating unnecessary risks for you
and your passengers.
If in doubt about any serv icing, have it done
by your author ized Audi dealer or any properly
equ ipped and qu alified workshop. We strong­
l y urge you to give your authorized Audi dea ler
the opportunity to perform all scheduled maintenance and necessary repairs . Your deal­
er has the facilities, or iginal parts and trained
specialists to keep your veh icle running prop­
erly.
Performing lim it e d m aint en anc e y ourself
The following pages describe a limited num­
ber of procedures which can be performed on
you r vehicle with ordinary tools, should the
need arise and trained personnel be unavaila­
ble. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and ca refully follow the instruc­
tions given. Always rigorously obse rve the
WARNINGS p rovided .
Before you ch eck anything in th e engine
compartm ent, alw ays read an d hee d all WARNINGS
¢ & a
nd ¢ & in Working in the
engine comportment on page 214 .
A WARNING
--Serious personal in jury may occur as a re-
sult of improperly performed mainte­ nance, adjustments or repa irs.
- Always be extremely careful when work­
ing on the vehicle. Always follow com­
monly accepted safety pract ices and gen­
eral common sense. Never r isk personal
in jur y.
- Do not attempt any of the maintenance,
checks or repairs descr ibed o n the fol­
lowing pages if you are not fu lly fam iliar
with these or other procedures with re­ spect to the ve hicl e, or are uncerta in how
to proceed .
- Do not do any work withou t the proper
too ls and equipment . Have the necessary
work done by your authorized A udi deal ­
er or any properly equipped and q ualified
workshop.
- The engine compar tment o f any motor
vehicle is a potentially hazardous area. Never reach into the area around or
touch the rad iator fan. It is temperature
control led and can sw itch on suddenly -
even when the engine is off and the igni­
tion key has been removed. The rad iator
fan switches on automatically when the coo lant reaches a certain tempera ture
and will cont inue to run until the coo lant
temperature drops .
- Always remove the ign ition key befo re
a nyone gets under the veh icle.
- Always suppor t your veh icle with safety
s tands if it is necessary to work under­
neath the vehicle. The jack s upplied with
the vehicle is not adequate for this pur ­
pose and co uld co llapse causing serio us
personal injury.
- If you must work unde rneath the vehicle
with the wheels on the ground, a lways
make sure the vehicle is on leve l ground,
that the wheels are always securely blocked and that the engine cannot be
started.

28 0 Index .:..:..:..::....::.. ...:..._ ___________________________ _
A
Accessories . . . . . . . . . . . . . . . . . . . . 64, 277
AC (automatic cl imate control) ... .. .. . . 77
adaptive cruise control Vehicles with manual transmission .. . 101
Adapt ive cruise control . . . . . . . . . . . . . . . . 99
C leaning the sensor .. ... .. .. .. .... . 205
Messages . . . . . . . . . . . . . . . . . . . . . . . . 107
Request for dr iver intervention . ..... . 105
Setting the driving program .. .. .. ... 104
Adapt ive dampers .......... .... .... . 113
Adapt ive light ................ ... .... 47
Adaptive Lig ht (defective) ... .. .. .... .. 22
Adding Eng ine coolan t .................... 222
E ng ine oil . .... .. ..... ... .. .. .... . 219
Windshield washer fluid ... .. .. .... . 228
Addit ional accessories
Addit ives 277
Eng ine oil .. ............. .. .. .. .. . 219
Ad justab le steering column . ... .. .... .. 80
Adjust ing
A ir dist ribution (automatic climate con -
trol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
I ns trumen t illum inat ion . .. .. .. .. .. . . 50
Steer ing column .. ..... ... .. .. .... .. 80
Temperature (automatic climate control) 78
A irbag
War ning/ indicato r ligh ts ... .... .... .. 20
A irbag system . . . . . . . . . . . . . . . . . 146, 162
Advanced Airbag System ........ .... 150
Advanced Airbag System components . 153
Care . .. .. .. ........ ........ ..... . 159
C hil dren . ............... .. .. .. .. . 168
Ch ild restr aints ........... .. .. .. .. . 169
Components (front airbags) .. .... .. . 153
Danger of fitting a child safety seat on
the front passenger seat . . . . . . . . . . . . 147
Disposal . .... ........... .. .. .... . 159
Front airbags . . . . . . . . . . . . . . . . 150, 151
H ow do the front airbags work? . .. .. . 155
H ow many airbags does my vehicle
have? .... ................... ... . 153
H ow the Advanced Airbag System com-
po nents work together ............. 154
I mpor tan t things to know .. .. .. .. .. . 14 6 Indicator light
... ... .. ..... .... . .. 156
Monitoring . ..... .. ... ..... ... .. .. 156
PASSENGER AIR BAG OFF light ... .. .. 157
Repairs ... .... .. ............. .... 159
Safety instructions ................. 158
S ide a irbags ..... ................ . 161
S ide cu rtain airbags ........... ... .. 164
Weight-sensing mat ............... 168
When must the sys tem be inspected? 156
Alcantara Cleaning ...... ................... 207
all-wheel drive
All wheel d rive 192
Winter tires . .. .. .. ........... .. .. 246
Alternator
refer to Generator . . . . . . . . . . . . . . . . . . 17
Anti-freeze
refer to Engine coolant system ....... 221
An ti-lock brak ing system ............. 186
W arning/ind icator lights . . . . . . . . . 18 , 19
An ti-slip regulation ................ . 186
Warning/ind icator lights ........... .. 18
Anti-theft alarm warning system ... .... . 32
An ti- theft systems
El ectronic immob ilizer .. ..... .... . .. . 38
Armrest ...... .. .. .. ... ....... ... .. . 60
Ashtray .. .. .. .. .. ............. .. .. . 63
As te ris k
Wha t does i t mean when something is
marked w it h an asterisk? . . . . . . . . . . . . . . 6
Audi braking guard
refer to b ra ki ng guard .......... .. .. . 99
Audi drive select ... ............. .... 113
Adaptive dampers ................. 113
Description ...... ................ . 113
Dynam ic steer ing ................. . 113
Setting the dr iv ing mode ........ .... 114
Spo rt differential . ............. .... 113
Audi Serv ice Repair Manuals and Litera-
ture 275
AUTO Automat ic climate control . . . . . . . . . . . . 78
Automat ic headlights .......... .. .. . 47
A ut o Lock . ..... .. .. .... .... ... .. .. . 32
Automat ic be lt retractor ............. 141

Automatic climate control Air vents ... .... .. .... ... .. .. .. .... 78
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 77
Setup ... .. ................. .. .... 79
Automatic S hift Lock (ASL) . . . . . . . . . . . . 93
Automatic transmission ......... ... ... 91
Automatic S hift Lock (ASL) . . . . . . . . . . . 93
D riving .. .. ............. .... .. .. .. 9 3
E mergency mode . . . . . . . . . . . . . . . . . . . 97
E me rgency release . . . . . . . . . . . . . . . . . . 98
Kick -down . . . . . . . . . . . . . . . . . . . . . . . . . 96
M anual shift program .. ... .. .. .. .. .. 96
Remova l lock (ignition key) ... .. .. .. .. 80
Selector lever . . . . . . . . . . . . . . . . . . . . . . 92
Automatic wipe rs . . . . . . . . . . . . . . . . . . . . 53
Auto Safety Hotline ............. .... 136
Average speed . . . . . . . . . . . . . . . . . . . . . . . 25
Avoid damag ing the vehi cle .. .. .. .. .. . 195
B
Bag hooks . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Battery . . . . . . . . . . . . . . . . . . . . . . . 17,225
Battery location inside the luggage com -
partment .. .. ........... .. .. .. ... 225
Charging . ................ ... ... .. 227
Important war nings when wo rking on
the battery . ................ ... ... 225
J ump starti ng ............ .... .. .. . 266
L ow . .. .. .. .. .. ........... .. .. ... 193
Replacing the ba ttery .. ... .. .. .. .. . 228
State of charge . ....... ... .. .. .. ... 193
Winter operation . ..... ... .. .. .. .. . 225
Working on the battery .... .. .. .. .. . 225
B efore dr iving ............. .... .. .. . 128
Bio-ethanol (Fuel) ..... ..... .. .. .. .. . 210
Blended gasoline ... .... ... .. .. .. .. . 209
B lower (automatic climate cont rol) . . . . . . 78
Booster seats ............. .... .. .. . 175
B rake fl uid
C hanging the brake fl uid ... .. .. .. .. . 224
Chec king the brake fluid level ... .. .. . 224
Reservoir .. ............. .... .. ... 224
What is the correct brake flu id leve l? . . 224
What should I do if the brake fluid warn-
i ng light comes o n? .. ..... .. .. .. .. . 224
Inde x 281
Brake system . ..... ... .. .. ..... ... .. 224
Anti- lock b raking system ..... ... .. .. . 19
B rake assist system .. .. ..... ... .. .. 186
Brake fluid .. .. .. ................. 224
Brake fluid specifications for refill and re-
placement ...... .. ............... 224
B rake light defective ... .. .. ... ... .. . 21
B ra ke powe r ass ist unit ............ . 189
Br akes .. .. .. .. .. .. . .............. 189
Ce ram ic bra kes . .. .... ........... .. 189
El ec tromechanica l parking brake ... .. . 85
Warning/indicator lights ..... ... .. .. . 15
Wor n brake pads symbo l . . . . . . . . . . . . . 20
B ra kin g
E mergency b ra ki ng f unction ..... .. .. . 87
braking guard . . . . . . . . . . . . . . . . . . . . . . . 99
Messages . . . . . . . . . . . . . . . . . . . . . . . . 107
Settings ........ .. ............... 106
Break -in per iod .. .. .... ............. 195
Tires ... .. .. .. .. .. ............... 195
Bul bs . ... .. .. .... .. . .. .. ..... ... .. 2 64
C
Califor nia Proposition 65 War ning . .. .. 215
B attery spec ifi c .. ............. .. .. 226
Capacities ........ .. ............... 273
Carbon pa rts
Cleaning . . . . . . . . . . . . . . . . . . . . 206, 207
Care ..... .. .. .. .... ... .......... .. 20 4
Cargo a rea
refer to L uggage compartment . . . 68, 134
Catalytic converter ... .. ...... ... .. .. 196
Cen te r armrest . . . . . . . . . . . . . . . . . . . . . . 60
Central lock ing .. .. ................. . 32
Cen tral lock ing switch ............. .. 36
Co nvenience key . . . . . . . . . . . . . . . . . . . . 36
Remote cont ro l key . ........... .... . 35
Ceram ic brake rotors
New brake pads .. ............. .... 189
Ce rtification . ... .... . ... ...... ... .. 278
Chang ing a flat t ire . .. ... ....... .... . 255
Chang ing a wheel .. ............. .... 255
Chang ing engine oil ............. .... 220
Checking Engine coolant level .... ....... .... . 221
Checking t ire pressure ............... 237
•
•