2014 AUDI S4 garage door opener

124 Homelin k
Homelink
Universal remote
control
Description
Appl ies to vehicles: wit h Homeli nk
The HomeLink universal remote control can
be programmed with the remote control for
devices that are already present.
W ith Home Link, you can control devices such
as the garage door, security systems, house lights, etc. comfortably from the inside of you
vehicle.
Homelink makes it possible for you to replace
three d ifferent remote controls from dev ices
in your home with one universal remote. This
feature works for most garage door and exte­
rior door motor signals. Programming the in­
div idual remote control for your remote con ­
trol takes place near the center of the radiator
grille. There is a control module attached at
this location .
A one -time programm ing of the sensor must
be performed before you are able to use sys­
tems with Home link. If the system does not
activate after performing the one-time pro­
gramm ing, check whether the system uses a
rolling code
q page 127 for vehicles without
the MMI*.
& WARNING
-
- Never use the Homelink transmitter
with any garage door opener that does
have not the safety stop and reverse fea­
ture as required by federa l safety stand­
ards. This includes any garage door open­
er model manufactured before April 1,
1982.
- A garage door opener which cannot de­
tect an object, signaling the door to stop
and reverse does not meet current feder­
al safety standards. Using a garage door
opener without these features increases
risk of serious injury or death. -
For safety reasons never release the
parking brake or start the engine while
anyone is standing in front of the vehicle.
- A garage door or an estate gate may
sometimes be set in motion when the
Homelink remote control is being pro­
grammed. If the device is repeatedly ac­
tivated, this can overstrain motor and
damage its e lectrica l components - an
overheated mo tor is a fire hazard!
- To avo id possib le injuries or property
damage, please always make abso lutely
certain that no persons or objects are lo­
cated in the range of motion of any
equipment being operated.
{D Tips
- If you would li ke more information on
Homel ink, where to purchase the Home­
Link compat ible prod ucts, or wou ld like
to purchase the Homelink Home Light­
ing Package, please call toll-free:
1-800-355-3515.
- For Declaration of Compliance to United
States FCC and Industry Canada regula­
tions
¢ page 2 78.
- For security reasons, we recommend that
you clear the programmed buttons be­
fore selling the vehicle.
Operation
Applies to veh icles : w it h Ho meli nk
~ ,.......,,...--, ........... ~
,;,,, r . o : o . ) .~
®
Fig. 136 Headl iner: controls
Requirement : The buttons must be program-
med
¢ page 125 or ¢page 126. II>

.. To open the garage door, press the program­
med button. The LED® will light up or
flash.
.. To close the garage door, press the button
again.
@ Tips
To open the garage door, press the button,
but do not press it for longer ten seconds
or the Homelink module will switch to
programming mode.
Programming the transmitter (version A)
A pp lies to vehicles : wit h Homelink a nd MMI
Fig. 137 Distance between the radiato r grille an d the
hand trans mitter
You can program the fixed code and rolling
code systems using the described procedure.
Programming the button
.. Turn the ignition on .
.. There are two ways to program the button:
Press the button ¢
page 124, fig. 136 that
you would like to program. Use the instruc­
tions that appear in the MMI* to perform
the programming. Or
.. Select :
I CARI function button > Car systems*
control button > Vehicle settings> Garage
door opener> Program garage door open·
er .
If this path is not available, program
Homelink as described in version B
¢page 126.
.. Select the button that you would like to pro ­
gram.
.. Follow the instructions in the MMI*.
.. If the garage door opening must also be
synchronized with the Homelink module,
Homelink 125
refer to the owner's manual for the garage
door opener.
Remote control units for garage door openers
in Canada are set to stop transmitting radio
frequency signals after two seconds. This time
may not be sufficient for the Home Link sys­
tem to learn the radio frequency signal. Per­
form all other steps as described above.
Erasing/Clearing the programmed button
settings
.. To erase all of the programmed buttons at
the same time, select:
I CAR ! function button
> Car Systems* control button > Vehicle set·
tings> Garage door opener > Clear pro·
gram settings> Yes .
The programmed but­
tons can not be erased individually. Repro­
gram the buttons if necessary .
.. Reprogram an individual button in the same
manner that you would for the one-time
programming .
Displaying the version/status/country
code
.. Select: !CAR ! function button > Car systems*
control button > Vehicle settings > Garage
door opener > Version information .
(D Tips
- Programming through the MMI* is not
possible with all infotainment systems .
If this is the case, program Homelink as
described in version B
¢ page 126 .
-The required distance between the hand
transmitter and the Homelink module in
the radiator grille
¢fig. 137 depends on
the system that you are programming .
- Depending on the model of the garage door opener, you may need to release the
button on the remote and press it again
when programming. When program­
ming a new device, keep the button
pressed for at least 15 seconds before
trying again with the transmitter in a dif­
ferent position. Watch out for the emer­
gency flasher during that time .

126 Homelink
Programming the transmitter
(version B)
Applies to vehicles: with Homelink
F ig. 138 Distance between t he rad iator grille and the
hand transm itter
P rogramming: phase 1 on th e control unit
1. Sw itch on the ign it ion (do not start the
engine) .
2. Press and hold both of the outer Home­
Link buttons
¢ page 124, fig. 136 unti l
the LED @turns off completely (about
20
seconds). Th is procedure clears the stand­
ard codes that were set at the factory and
does not need to be repeated again to
p rogram the other buttons .
3 . Briefly press the Homelink button that
you would like to prog ram .
4. Wai t unti l the LED @ beg ins to blin k
q uickly. The Homelink module wi ll now
remain in learning mode for
5 minutes .
5. Now stand in front of your vehicle with
the original hand transmitter for the ga­
rage door opener or for the device that
you would like to allocate to the Home­
Link button .
P rogramming: pha se 2 on the radiator
gr ille
6 . Hold the orig inal hand transmitter some­
what towa rds the center of your vehicle's
r adiato r grille ¢
fig. 138 .
7. Now activate (p ress) the hand transmit­
ter.
8 . Pay attention to the tu rn signals fo r your
vehicle when activating the hand trans­
mitter . If the emergency flashers blink
three times, the programming was suc­
cessful. If the emergency flasher only blinks one time, the S minute time limit f
or the adaptation has expired or the pro ­
gramming was unsuccessful. Repeat the
programming from step 3 on the controls
or select another distance from the radia­
tor grille.
9 . If the garage door or other devices still
fail to be activated w it h the HomeL ink
control buttons after programming is
comple ted, it is possib le tha t these sys ­
tems mig ht be work ing with a roll ing code
instead of the normal f ixed code .
A Roll­
ing code programming must be per­
formed
¢ page 127 .
Program the remaining two buttons accord ing
to the instructions mentioned above . Begin
similarly with the 3rd step if the program ­
ming connection was successful for the first
button.
Remote contro l units for garage door openers
in Canada are set to stop transmitting radio
frequency signa ls after two seconds. This time
may not be suffic ient for the Homelink sys­
tem to learn the radio frequency signa l. Per­
form all other steps as described above.
E rasing the button s
.,. Switch on the ignition (do not start the en­
gine).
.,. Press and hold both of the outer buttons un­
til the LED @turns off completely (about
20 seconds) to erase all of the buttons si­
multaneously .
.. Programmed buttons cannot be erased ind i­
vidua lly. Reprogram the buttons if necessa­
ry .
Reprogramming the buttons
.. Switch on the ignition (do not start the en­
gine) .
.. To reprogram an individua l button, press
and hold the b utton unt il the L ED@starts
to f lash quickly (after abo ut ten seconds).
Release the button immedia tely. The Home­
Link module will now remain in learning
mode for 5 minutes.
.,. Continue with step 5.

@ Tips
-Programming using the Homelink but­
tons is not possible with all infotainment
systems. If this is the case, program Homelink as described in version A
<=> page 125.
-The required distance between the hand
transmitter and the Homelink module in
the radiator grille<=>
fig. 138 depends on
the system that you are programming.
- Depending on the model of the garage
door opener, you may need to release the
button on the remote and press it again
when programming. When program­
ming a new device, keep the button
pressed for at least 15 seconds before
trying again with the transmitter in a dif­
ferent position. Watch out for the emer­ gency flasher during that time.
Programming the rolling code
App lies to vehicles: with Home link
Additionally, a rolling code programming for
the Homelink universal remote control is re­
quired for some systems.
Identifying the rolling code
"'Press the previously programmed Homelink
button again and hold it down.
"'Look at the
LED@r=)page 124, fig. 136. If
the LED blinks quickly, the features, such as
the garage door opener, are equipped with
the rolling code.
"'Program the rolling code as follows:
Activating the garage door opener motor
unit
"'Locate the setting button on the garage
door opener motor unit. The exact location
and color of the button may vary depending
on the garage door opener manufacturer .
"'Press the setting button on the garage door
opener motor unit (usually this will activate
a "setting light display" on the motor unit).
Now you will have about
30 seconds time to
perform the HomeLink button programming
on the controls.
Homelink 127
Programming on the controls
"'Press the Home Link button that was already
programmed and hold for two seconds.
"'To end rolling code programming , press and
hold the Home link button for two seconds
again.
"'The Homelink button may need to be press­
ed a third time to end the adjustment proce­
dure for some garage door openers .
After the controls have been programmed, the garage door opener should recognize the
Homelink signal and operate when the Home ­
Link button is pressed . Now you may program
the other buttons as needed .
(D Tips
- Programming the rolling code can be
performed quicker and more easily with
the help of a second person.
- If difficulties should arise when pro­
gramming the rolling code, consult the
operating instructions for the garage
door opener or other devices for possible
solutions.

_______________________________ ___:I~n~d~e:.::x 285
Fuel
Additives ... ................ ... ... 209
Blended gasoline ............ ... .. . 209
Consumption . . . . . . . . . . . . . . . . . . . . . . 25
Filler neck .. ............. .... .. ... 211
Fuel gauge . ................ ... ... . 12
Gasoline ... ... .. .. ...... .. .. .. .. . 209
Gasoline additives ........... .... .. 211
L ow fuel level symbol . . . . . . . . . . . . . . . 21
Octane rating ............ .... .. ... 209
Recommendation ............ ... .. . 209
Refuelling . ................. ... ... 212
Reserve .... ................ ... .... 12
T ank capacity . ........... .. .. .. ... 273
Tank system ............. .... .. .... 21
Unlocking the fuel filler flap by hand . . 213
F uel economy messages (efficiency pro-
gram) .......................... .... 29
Fuel filler flap
Un locking the fuel filler flap by hand . . 213
Fuses Assignment . . . . . . . . . . . . . . . . . 261, 263
R l . ep acing .................. .... .. 261
G
Garage door opener (Homelink) .. .. .. . 124
Garment hooks . . . . . . . . . . . . . . . . . . . . . . 66
Gas discharge lamps ........ .. .. .. .. . 264
Gauges Engine coolant tempera ture .. .. .. .. .. 10
Fuel gauge ................. .... ... 12
Tachometer . . . . . . . . . . . . . . . . . . . . . . . 11
Gear recommendation . . . . . . . . . . . . . . . . 28
G h.ft . d'
ears
I in 1cator ......... .. .. .. .. .. 27
Gearshift lever 6-speed manual transmission . .. . ... .. 91
General illustration Instruments and controls . . . . . . . . . . . . . 8
Generator Warning/indicator lights ......... .. .. 17
Glossary of tire and loading terminology 231
Glove compartment . . . . . . . . . . . . . . . . . . 65
Valet parking ............ .... .. .... 46
GPS controlled clock .. .... .. .. .. .. .. .. 12
Gross Vehicle Weight Rating (GVWR) ... 272
Ground clearance .................. . 199
H
Headlights
Cleaning ... ..... .. ............... 205
Cleaning system . . . . . . . . . . . . . . . . . . . . 53
Defective . . . . . . . . . . . . . . . . . . . . . . . . . 21
Headlight range control ............ . 22
Left hand drive, right hand drive .. .. .. . 49
Travel mode . . . . . . . . . . . . . . . . . . . . . . . 49
Headlight washer reservoir ......... .. 228
Head restraints .. .. .......... ....... 132
Adjusting . . . . . . . . . . . . . . . . . . . . 61, 132
Removing/installing .............. .. 61
Heated exterior mirrors . . . . . . . . . . . . . . . . . . . . SO
rear window . .. .. .... ........... .. . 78
seats ..... .. .. .. .... ............. . 78
windshield washer spray nozzles . . . . . . 53
Heating ......... ... ..... ........... 76
Heavy clothing and saf ety belts ....... . 141
High beam .. .. .. .. .. . ... .. ..... .... . 48
High voltage warning label .. ....... .. 272
Hill descent control .................. 95
Homelink (remote control) ......... .. 124
Hood Opening .. .. .. .. .... ............. 214
Release lever . . . . . . . . . . . . . . . . . . . . . 214
Hooks ............................. 72
Horn .. .... .. .... ..... ... ... ... ... .. 8
How are child restraint system anchors re-
la ted to child safety ........... .. .... 181
How many airbags does my vehicle have? 153
How often should I check my tire pres-
sures? 238
How safe ty bel t pre ten sioners work .. .. 144
Hydroplaning ..... .. ............... 240
I
Ignit ion
switching on/off .. ...... .. .. ... .... . 80
Ignition key Emergency unlocking .......... .... .. 35
Ignition lock .. .. .. ...... .. ... ...... . 80
Indic ato r light . .. ........... ...... . 18
Mal func tion . . . . . . . . . . . . . . . . . . . . . . . 22
Immobilizer . . . . . . . . . . . . . . . . . . . . . . . . 12
•
•