2014 AUDI Q5 Owners Manual

Vehicles with a trailer hitch *
• Install the trailer h itch .
• Attach the towing bar or the towing cab le to
the trai le r hitch.
Unscrew the towing loop aga in after use and
i nstall the cover in the bumper. Return the
t owing loop to the vehicle too lkit. Be sure to
have the towing Loop stored in the vehicle at
all times.
A WARNING
- If the towing Loop is not screwed in as far
as it will go, the thread can pull out when
the vehicle is towed -potential risk of an
accident.
- If your veh icle has a
trailer h itch * only
use a special towing bar to prevent dam­
aging the ball h itch . These towing bars
have been specially designed for trailer
towing hi tches.
- If your veh icle has a
trailer hi tch* use on­
ly specia l towing cables.
Loading the vehicle onto a flat bed truck
Fig. 235 Veh icle on fla t bed tru ck
Front hook up
• Align the vehicle w ith the centerline of the
car carr ier ramp.
• Att ach the winch hook to the front towline
eye previously installed .
Rear hook up
• Align the vehicle with the centerline of the
car car rier ramp.
• Attach the winch hook to the rear towline
eye previously installed .
Emergency situ ation s 287
@ Tips
Check caref ully to make sure the hook-up
i s secure before moving the car up the flat­
bed truck ramp.
Lifting vehicle
Lift ing w ith workshop hoist and with
floor jack
The vehicle may only be lifted at the lifting
points illustrated.
F ig . 236 Fro nt li fting point
F ig . 237
Rea r liftin g po int
• Read and heed WARNING ¢ ,&. .
• Locate lifting points ¢ fig. 236 and
¢fig. 237.
• Adjust li fting arms of workshop ho is t or
floor jack to match veh icle lifting points .
• Insert a rubber pad between the floor jack/
workshop hoist and the lift ing poin ts .
If you must l ift your vehicle with a floor jack
t o work und erneath, b e sure the vehi cle i s
saf ely s upported on stands int ended for thi s
purpo se.
Fron t lifting point
The lifting poin t is located on the floor pan re-
inforcement about at the same level as the
Ill>

288 Emergency situations
jack mounting point¢ fig. 236 . Do not lift
the vehicle at the vertical sill reinforcement.
Rear lifting point
T he lifting point is lo cate d on t he ve rtical rein­
fo rceme nt of the lower s ill fo r th e on bo ard
j ack *¢
fig . 23 7.
Lifting with vehicle jack*
Refe r to ¢ page 2 75 .
..&, WARNING
- T o redu ce t he r is k of se rious injury and
vehicle dam ag e.
- Always lift the vehicle on ly at the spe­
cial wor kshop h oist and floor jack lift
points illustrated
¢ fig. 236 and
¢ fig. 237 .
-Fa ilure to lift the vehicle at these
points cou ld cause the veh icle to tilt or
fa ll from a lift if the re is a change in ve­
h icle we igh t di stribu tion a nd ba lance .
This might happen, for exa mple, w hen
h eavy co mpo ne nts su ch as the engi ne
bl oc k or tra ns mis sion ar e removed .
- W hen re mov ing heavy co mpo nents like
t h ese , a nch or vehicle to hoist or add cor­
res pond ing weig hts to maintain t he cen ­
te r of gravity . Othe rwise, the vehicle
mi gh t tilt o r slip off t he hoist , ca usi ng
serious persona l injury .
CJ) Note
- Be aw ar e of t he fo llow ing poin ts be fo re
lift ing t he vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil pan, the transmission housing, the
front or rear axle or the body side members. Thi s could lead to serious
damage.
- To avoid damage to the underbody or
chassis frame , a rubber pad must be
inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
-
exceed the permissible lifting capacity
of the hoist .
- Before driving over a workshop hoist,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.

Technical Data
Vehicle identification
F ig. 238 Veh ide Identificat ion Numbe r (VlN) plate: lo ·
c ation on dri ver 's s ide das h pane l
XXXXX XX · X -XXXX XXX
~ fAllftlli. -llllll · NR. ~ W!ru -IIOO -NO.
xx
XXXX XXXX XX X XXXXXXXX
XXX XXX
IYP /TYPE
XX XXXXXXX XX X X XX
XXX KW XXX
®i ~W.::·f :l~~ XXXX XXX XXX
©+ ::rw= xxxx I xxxx XXX I xx
M. · AUSSt I IJ'IIDIIS
~--
EOA 7D 5 4UB 6XM SSG SRW
2E H JDZ 1LB lA S 1BA
3FC SMU 7X l
FD A 9G3 OG7 OYH OJF
TL6 3 KA 8EH UlA X98 027
lXW 803 908 824 D2D
7T6 CV7 7KO 4X3 2K2
3L4 4KC 3YO 413 502
1S A 7GB 01A 4GO
XX. X XX X XX X XXXX
Fig. 239 Vehicle identificat io n label: ins ide t he lug ­
ga ge compar tmen t
Vehicle Id entification Numb er (VlN )
The Veh icle Iden tifica tion Number is located
in different p laces :
- under the w indshield on the driver's side
¢fig. 238.
- i n the radio or in the MM!*: Select:
ICAR I
function button > Vehicle ID numb er (VIN )
or select I CAR I func tion button > Car sys·
tem s* control button > Servicin g & check s >
VIN numbe r.
-on the vehicle identification label.
Te chni cal Data 289
Vehicle id ent ification label
T he vehicle identification label is located in
the luggage compartment above the com­
partment fo r th e ve hicle tools.
T he label¢
fig. 239 shows the fol low ing vehi­
cle data :
(D Vehicle Ident ificat ion Number (VIN)
@ Vehicle type, engine o utp ut, transmission
® Engine and transmission code
© Paint number and inte rior
® Optional equipment numbers
T he information of the vehicle identification
label can also be found in your Warranty
&
Maintenance booklet .
Safety compliance sticker
T he safety compliance sticker is your assur­
ance that your new veh icle complies with all
applicable Fede ra l Motor Vehi cle Safety
Standards which were in effect at the time the
vehicle was manufactured . You can find this
sticker on the door jamb on the driver 's side.
It shows the month and year of production
and the vehicle ident ificat ion number of your
vehicle (perforation) as well as the Gross Veh i­
cle Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
High voltage warning label
The high voltage warning label is located in
the engine compartment next to the engine
hood release. The spark ign ition system com­
plies with the Ca nadian standard ICES-002 .
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rat ing (GVWR), and
the Gross Axle Weight Rati ng (GAWR) for
front and rear are listed on a sticker on the
doo r jamb on the driver's side.
The Gross Vehicle Weight Rat ing includes the
weight of the basic vehicle plus full fuel tank,
o il and coolant, plus maximum load, which in ­
cludes passe nger we ight (150 lbs/68 kg per
II>--

29 0 Techni cal Dat a
designated seating position) and luggage
weight ¢.&, .
Gross Axle W eight Rating
The Gross Axle Weight Rating is the maximum
l oad that can be applied at each axle of the
vehicle ¢Lr!, .
Vehicle cap acit y weight
The vehicle capac ity we ight (max. load) is list­
ed on the driver's side 8-p illar.
A WARNING .
- T he actual Gross Axle Weight Rat ing at
the front and rear axles sho uld not ex­
ceed the permissible weights, and their
combination must not exceed the Gross
Vehicle Weight Rating.
Dimensions
Leng th in (mm)
Width in (mm)
Width (across mir rors) in (mm)
He ight (unloaded)a ) in (mm)
T urning circle diameter
ft (m) -
Exceeding permissible weight ratings can
result in veh icle damage, acc idents and
personal injury.
(D Note
- The vehicle capacity weight figures apply
when the load is distributed evenly in the
vehicle (passengers and luggage). When
transport ing a heavy load in the luggage
compartment, carry the load as near to
the rear axle as poss ible so that the vehi­
cle's handling is not impaired.
- Do not exceed the maximum permissible
axle loads or the maximum gross veh icle
we ight. Always remember that the vehi­
cle's handling w il l be affected by the ex­
tra load. Therefo re, adj ust your speed ac­
cordingly.
- Always observe local regulat ions.
QS /QS hybrid SQS
182.6 (4639) 183 .0 (4647)
74 .7 (1898) 75 .2 (1911)
82.2 (2089) 82 .2 (2089)
65 .2 (1655) 65 .3 (1658)
38.1 (1 1.6) 38. 1 (1 1.6)
a) The he ight of the vehicle depen ds on the tires and the suspension.
When driving up steep ramps, on rough roads,
over curbs, etc . it is important to remember
that some parts of your ve hicle, such as spoil-
Capacities
ers or exhaust system components, may be
close to the ground. Be carefu l not to damage
them.
QS /SQS QS hybrid
Fuel tank: tota l capacity gal (liters) approx. 19 .8 (75) approx. 19.0 (72)
Winds hield and headlight* quarts ( liters) approx. 4
.9 (4.6)
approx. 4.9 (4.6)
washer fluid container

Technical Dat a 291
Gasoline engines
•
QS 2.0, 4 cylinder •
Maximum output SAE net hp@rpm 220 @ 4450 - 6000
Maximum torque SAE net lb-ft@ rpm 259@ 1500 - 4300
Displacement CID (cm
3
) 121.1 (1984)
Engine oil with f ilter change q
uarts (liters) 4.9 (4 .6)
Fuel
Prem ium unleaded (91 AKI) <=> page 222, Fuel supply
or Bio-ethanol (E85) <=> page 223, Ethanol fuel (Bio-etha-
no/).
QS 2 .0 hybrid, 4 cylinder
Max imum output SA E net hp@rpm 211 @4300 -6000
Maximum torque SAE net l
b-ft@ rpm 258@ 1500 -4200
Displacement CID (cm
3
) 121. 1 (1984)
Engine oil with filter change quarts (li ters) 4.9 (4.6)
Fuel
Prem ium unlead ed (91 AKI) , c:> page 222, Fuel supply
Electr ic output (short-term)
hp 54
El ectr ic to rque (shor t-te rm) lb-ft 155
Total output (short-term) hp 245
T ota l torque (short-te rm) lb -ft 354
Battery type Lithium-ion
Batte ry energy con ten t kWh 1.3
QS 3.0, 6 cylinder
Max imum ou tpu t SA E ne t hp@ rpm 272 @4780 - 6 500
Max imum torque SAE net lb-ft@ rpm 295@ 2150 - 4780
Displa cemen t CID (cm
3
) 18 2 .8 (2995)
Engine oil with f ilter change quarts (liters) 7.2 (6.8)
F uel
Premium unleaded (91 AKI) , <=> page 222, Fuel supply
SQS 3.0, 6 cylinder
Max imum ou tpu t SA E ne t hp@rpm 354@ 6000 - 6 500
Max imum torque SAE net lb-ft@ rpm 346.65 @4000 - 4500
Displacement CI
D (cm
3
) 18 2.8 (2995)
Engine oil with filter change quarts (liters) 7
.2 (6 .8)
Fuel
Premium unleaded (91 AKI) , c:> page 222, Fuel supply

292 Technical Data
Diesel engine
QS 3.0 TDI, 6 cylinder
Maximum output SAE net hp@rpm 240@ 3750 - 4000
Max imum torque SAE net lb-ft@ rpm 4
28@ 17 50 -22 50
Displacement CID (cm
3
) 181.1 (2967)
E ngine oil with f ilter change qu
arts ( lite rs) 6.8 (6.4)
Fuel
ULSD-Diesel No. 2 , c> page 224, Diesel fuel

Consumer Information
Warranty coverages
Your Audi is covered by the following war­
ranties :
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfo-
ration
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Con trol Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warran ­
ties can be found in your
Warranty & Mainte­
nance booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulations in the United States
and Canada require that automobiles meet
specific emission regulations and safety
standards. Therefore, veh icles built for the
U.S.A. and Canada differ from vehicles sold in
other countries .
If you p lan to take your vehicle outside the
continental limits of the United States or Can­
ada, there is the possibility that:
- unleaded fuels for vehicles with cata lytic
converter may not be available;
- fuel may have a considerably lower octane
rating . Improper fuel may cause engine
damage ;
- service may be inadequate due to lack of
proper service facilities, tools or testing
equipment ;
- replacement parts may not be readily availa­
ble.
- Navigation systems for vehicles built for the
U.S.A. and Canada will not necessari ly work
in Europe, and may not work in other coun­
tries outside of North America.
Consumer Information 293
@ Note
Audi cannot be responsible for mechanical
damage that could result from inadequate
fuel, service or parts availab ility.
Audi Service Repair
Manuals and Literature
Audi Offic ial Factory Service Manuals and Lit ­
erature are published as soon as possible after
model introduction. Service Manuals and liter­
atu re are availabl e to order from the Audi
T echnical Literature Ordering Center at:
www.audi.techliterature.com
Maintenance
' General
Your vehicle has been designed to help keep
maintenance requirements to a minimum.
However, a certain amount of regular mainte­
nance is still necessary to assure your vehicle's
safety, economy and reliability . For detailed
vehicle maintenance consult your Warranty
&
Maintenance booklet.
Under difficult operating conditions , for ex­
ample at extremely low outside temperatures ,
in very dusty regions, when towing a tra iler
very frequently, etc., some serv ice work
shou ld be pe rformed between the intervals
specified. This applies particularly to:
- oil changes, and
- cleaning or replacing the air filter .
® For the sake of the environment
By regularly maintaining your vehicle, you
help make sure that emission standards
are maintained, thus min imizi ng adverse
effects on the environment .
Important considerations for you and
your vehicle
The increasing use of electronics , sophisticat­
ed fuel injection and emission contro l sys-
tems, and the genera lly increasing technica l ..,_
•
•

29 4 Con sum er Inf ormation
comp lexity of today's automobi les, have
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Also, s afety an d e nvir onm ent al con­
cerns place very strict limits on the nature of
repairs and adjustments to engine and trans ­
miss ion pa rts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth­
er equipment avai lab le to specially trained
workshop personnel in order to assure proper
performance, reliab ility and safety of the vehi­
cle and its many systems .
Improper ma intenance, adjustments and re ­
pa irs can impair the operation and reliab ility
of your vehicle and even void your vehicle war­ ranty. Therefo re , proof of servic ing in accord­
ance w it h the ma intenance sched ule may be a
condition for upholding a poss ible warranty
claim made within the warran ty period.
Above all, operational safety can be adve rsely
affected, c reating unnecessary risks for you
and your passengers.
If in doubt about any serv icing, have it done
by your author ized Audi dealer or any other
p roperly equipped and qualified workshop .
We strong ly urge you to give your authorized
Audi dealer the opportunity to perform all
schedu led maintenance and necessary repairs .
Your dea ler has the facilities, or iginal parts
and tra ined spec ialists to keep your vehicle
running properly .
Performing lim it e d m aint en anc e y ourself
The fo llowing pages describe a limited num­
ber of procedures which can be performed on
you r vehicle with ordinary too ls, shou ld the
need arise and trained personnel be unavaila­
ble. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and ca refully follow the instruc­
tions given. Always rigorously obse rve the
WARNINGS p rovided .
Before you ch eck anything in th e engin e
compartme nt, alway s read an d heed all WARNINGS
¢.&. and
¢ .&. in Working in the
engine comportment on page 231 .
A WARNING
--Serious personal in jury may occur as a re-
sult of improperly performed mainte­
nance, adjustments or repa irs.
- Always be extremely careful when work­
ing on the vehicle. Always follow com­
monly accepted safety pract ices and gen­
eral common sense. Never r isk personal
in jur y.
- Do not attempt any of the maintenance,
checks or repairs descr ibed o n the fol­
lowing pages if you are not fu lly fam iliar
with these or other procedures with re­
spect to the ve hicl e, or are uncerta in how
to proceed .
- Do not do any work withou t the proper
too ls and equipment . Have the necessary
work done by your authorized A udi deal ­
er or anothe r properly equipped and
qualified workshop.
- The engine compar tment o f any motor
vehicle is a potentially hazardous area. Never reach into the area around or
touch the rad iator fan. It is temperature
control led and can sw itch on suddenly -
even when the engine is off and the igni­
tion key has been removed. The rad iator
fan switches on automatically when the coo lant reaches a certai n tempera ture
and will cont inue to run until the coo lant
temperature drops .
- Always remove the ign ition key befo re
a nyone gets under the veh icle.
- Always suppor t your veh icle with safety
s tands if it is necessary to work under­
neath the vehicle. The jack* s upplied
with the vehicle is not adequate for this purpose and could co llapse causing seri­
ous personal injury .
- If you must work unde rneath the vehicle
with the wheels on the ground, a lways
make sure the vehicle is on leve l ground,
that the wheels are always securely blocked and that the engine cannot be
started.