2014.5 Citroen C4 PICASSO RHD Owner's Manual

287
Fuse N°Rating Functions
F18 10 ARight
  hand   main   beam
F19 10 ALeft
  hand   main   beam.
Type 2 fuse table
Fuse N°Rating Functions
F9 30 AMotorised
 t

ailgate.
F18 25 AHi-Fi
  amplifier.
F21 3 AHands-free
  starting   reader   unit.
Type 1 fuse table
Fusebox 1
Fusebox 2Fuse N° Rating Functions
F19 30 AFront
  wiper   slow   /   fast   speed.
F20 15 AFront
  and   rear   screenwash   pump.
F21 20 AHeadlamp
  wash   pump.
7
Practical information

288
12 V battery
The battery is located under the bonnet.
F or   access   to   the   (+)   terminal:
F
 
r
elease   the   bonnet   using   the   interior   lever,  
t

hen   the   exterior   safety   catch,
F
 
r
aise   the   bonnet   and   secure   it   with   its   stay,
F

l
ift the plastic cover for access to
the
  (+)   terminal.
Access to the battery
Procedure for starting the engine using another battery or charging a discharged battery.
T he presence of this label, in particular
with
  the   Stop   &   Start   system,   indicates  
t

he   use   of   a   12   V   lead-acid   battery   with  
s

pecial
 t
echnology
 a
nd
 s
pecification;
 t

he   involvement   of   a   CITROËN   dealer  
o

r   a   qualified   workshop   is   essential  
w

hen   replacing   or   disconnecting   the  
b

attery.
After
  refitting   the   battery,   the   Stop   &
 S

tart   system   will   only   be   active   after   a
 c

ontinuous   period   of   immobilisation   of   the
 v

ehicle,   a   period   which   depends   on   the
 c

limatic   conditions   and   the   state   of   charge
 o

f   the   battery   (up   to   about   8   hours). When
  your   vehicle's   battery   is   discharged,   the  
e

ngine   can   be   started   using   a   slave   battery  
(

external   or   on   another   vehicle)   and   jump   lead  
c

ables.
Starting using another
battery
First check that the slave battery has a nominal   voltage   of   12   V   and   a   capacity  
a

t   least   equal   to   that   of   the   discharged  
b

attery.
Do
  not   try   to   start   the   engine   by  
c

onnecting   a   battery   charger.
Do
  not   disconnect   the   (+)   terminal   when  
t

he   engine   is   running.
Practical information

289
Before disconnecting the battery
Wait 2 minutes after switching off the ignition before   disconnecting   the   battery.
Close
  the   windows   and   the   doors   before  
d

isconnecting   the   battery.
Following reconnection
of the battery
Following reconnection of the battery, switch on t
he   ignition   and   wait   1   minute   before   starting   to  
p

ermit   initialisation   of   the   electronic   systems.  
H

owever,   if   problems   remain   following   this  
o

peration,   contact   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Referring
  to   the   corresponding   section,   you  
m

ust
 y
ourself
 r
einitialise
 (
depending
 o
n
 ve

rsion):
-
 
t
he   remote   control   key,
-
 
t
he   electric   blind(s),
-
 ...
F

 
R

emove
 
the
 
plastic
 
cover
 
from
 

the
 
(+)
 
terminal,
 
if
 
your
 
vehicle
 
has
 
one.
F
 
C

onnect
 
the
 
red
 
cable
 
to
 
the
 
positive
 
t

erminal
 
(+)
 
of
 
the
 
flat
 
battery
 
A
, then to the
positive
 
terminal
 
(+)
 
of
 
the
 
slave
 
battery
 
B.
F
 
C

onnect
 
one
 
end
 
of
 
the
 
green
 
or
 
black
 
c

able
 
to
 
the
 
negative
 
terminal
 
(-)
 
of
 
the
 
s

lave battery B (or earth point on the other
vehicle).
F
 
C

onnect
 
t

he
 
o

ther
 
e

nd
 
o

f
 
t

he
 
g

reen
 
o

r
 
b

lack
 c
able to the earth point C
 
on
 
the
 
broken
 d
own
 
vehicle
 
(or
 
on
 
the
 
engine
 
mounting).
F
 
S

tart
 
the
 
engine
 
of
 
the
 
vehicle
 
with
 
the
 
g

ood
 
battery
 
and
 
leave
 
it
 
running
 
for
 
a
 
few
 
m

inutes.
F
 
O

perate
 
the
 
starter
 
on
 
the
 
broken
 
down
 
v

ehicle
 
and
 
let
 
the
 
engine
 
run
 I

f
 
the
 
engine
 
does
 
not
 
start
 
straight
 
away,
 
s

witch
 
off
 
the
 
ignition
 
and
 
wait
 
a
 
few
 
m

oments
 
before
 
trying
 
again.
F
 
W

ait
 
until
 
the
 
engine
 
returns
 
to
 
idle
 
then
 
d

isconnect
 
the
 
jump
 
lead
 
cables
 
in
 
the
 
r

everse
 o

rder.
F
 
R

efit
 
the
 
plastic
 
cover
 
to
 
the
 
(+)
 
terminal,
 
if
 
y

our
 
vehicle
 
has
 
one.
Some
 
functions
 
are
 
not
 
available
 
if
 
the
 
b

attery
 
is
 
not
 
sufficiently
 
charged.
7
Practical information

290
The batteries contain harmful substances such   as   sulphuric   acid   and   lead.   They m

ust   be   disposed   of   in   accordance
 w

ith   regulations   and   must   not,   in   any
 c

ircumstances,   be   discarded   with   household
 w

aste.
Take
  used   remote   control   batteries   and
 v

ehicle   batteries   to   a   special   collection   point.
Protect your eyes and face before handling   the   battery.
All
  operations   on   the   battery   must   be  
c

arried   out   in   a   well   ventilated   area   and  
a

way   from   naked   flames   and   sources  
o

f   sparks,   so   as   to   avoid   the   risk   of  
e

xplosion   or   fire.
Do
  not   try   to   charge   a   frozen   battery;  
t

he   battery   must   first   be   thawed   out   to  
a

void   the   risk   of   explosion.   If   the   battery  
h

as   been   frozen,   before   charging   have  
i

t   checked   by   a   CITROËN   dealer   or   a  
q

ualified   workshop   who   will   check   that  
t

he   internal   components   have   not   been  
d

amaged   and   the   casing   is   not   cracked,  
w

hich   could   cause   a   leak   of   toxic   and  
c

orrosive   acid.
Do
  not   reverse   the   polarity   and   use   only  
a

  12   V   charger.
Do
  not   disconnect   the   terminals   while  
t

he   engine   is   running.
Do
  not   charge   the   batteries   without  
d

isconnecting   the   terminals   first.
Wash
  your   hands   after wards.
It
 
is
 
advisable
 
to
 
disconnect
 
the
 
battery
 
i

f
 
the
 
vehicle
 
is
 
to
 
be
 
left
 
unused
 
for
 
m

ore
 
than
 
one
 
month.
do n
ot push the vehicle to start the
engine
  if   you   have   an   electronic   or  
a

utomatic   gearbox.Charging the battery using
a battery charger
F Disconnect   the   battery   from   the   vehicle.
F  F ollow   the   instructions   for   use   provided   by  
t

he   manufacturer   of   the   charger.
F
 
C
onnect   the   battery   starting   with   the  
n

egative   terminal   (-).
F
 
C
heck   that   the   terminals   and   connectors  
a

re   clean.   If   they   are   covered   with   sulphate  
(

whitish   or   greenish   deposit),   remove   them  
a

nd   clean   them.
With
  Stop   &   Start,   the   battery   does   not  
h

ave   to   be   disconnected   for   charging.
Do
 
not
 
apply
 
excessive
 
force
 
on
 
the
 
t

ab
 
as
 
locking
 
will
 
not
 
be
 
possible
 
if
 
the
 
c

lamp
 
is
 
not
 
positioned
 
correctly;
 
start
 
t

he
 
procedure
 
again.
Disconnecting the (+) cable
F Raise   the   locking   tab   D fully to release the
cable t erminal c lamp E.
Reconnecting the (+) cable
F Position   the   open   clamp   E of the cable on
the   positive   post   (+)   of   the   battery.
F
 
P
ress   vertically   on   the   clamp   E to position
it
  correctly   on   the   battery.
F
 
L
ock   the   clamp   by   spreading   the  
p

ositioning   lug   and   then   lowering   the   tab   D.
Practical information

291
Exiting economy mode
These functions are reactivated automatically next   time   the   vehicle   is   driven.
F

I
n   order   to   restore   the   use   of   these  
f

unctions   immediately,   start   the   engine   and  
l

et   it   run:
-
 
f
or   less   than   ten   minutes,   to   use  
t

he   equipment   for   approximately  
f

ive minutes,
-
 
f
or   more   than   ten   minutes,   to   use   the  
e

quipment   for   up   to   approximately  
t

hirty
 m
inutes.
Let
  the   engine   run   for   the   duration   specified   to  
e

nsure   that   the   battery   charge   is   sufficient.
Do
  not   repeatedly   and   continuously   restart   the  
e

ngine   in   order   to   charge   the   battery.
A
  flat   battery   prevents   the   engine   from   starting  
(

refer   to   the   "Battery"   section).
Load reduction mode
System which manages the use of certain functions   according   to   the   level   of   charge  
r

emaining   in   the   battery.
When
  the   vehicle   is   being   driven,   the   load  
r

eduction   function   temporarily   deactivates  
c

ertain   functions,   such   as   the   air   conditioning,  
t

he   heated   rear   screen...
The
  deactivated   functions   are   reactivated  
a

utomatically   as   soon   as   conditions   permit.
Energy economy mode
Switching to economy mode
A message then appears in the instrument p
anel   screen   indicating   that   the   vehicle   has  
s

witched   to   economy   mode   and   the   active  
f

unctions   are   put   on   standby.
If
  a   telephone   call   is   being   made   at   this   time,  
i

t will   be   maintained   for   around   10   minutes  
w

ith   the   Bluetooth   hands-free   system   of   your  
a

udio system.
System
  which   manages   the   duration   of   use   of  
c

ertain functions to conserve a sufficient level
of   charge   in   the   battery.
After   the   engine   has   stopped,   you   can  
s

till   use   functions   such   as   the   audio   and  
t

elematics   system,   windscreen   wipers,   dipped  
b

eam   headlamps,   courtesy   lamps,   etc.   for  
a

  maximum   combined   duration   of   about  
f

orty
 m
inutes.
7
Practical information

292
Changing a wiper blade
Before removing a front
wiper blade
F Within  one   minute   after   switching   off  t
he   ignition,   operate   the   wiper   stalk   to  
p

osition   the   wiper   blades   vertically   on   the  
w

indscreen,


or
F
 
F
rom   one   minute   after   switching   off   the  
i

gnition,   reposition   the   arms   manually.
Removing
F Raise  the   corresponding   wiper   arm.
F  U nclip   the   wiper   blade   and   remove   it.
Fitting
F Put  the   corresponding   new   wiper   blade   in  p
lace   and   clip   it.
F
 
F
old   down   the   wiper   arm   carefully.
After fitting a front wiper
blade
F Switch  on   the   ignition.
F  O perate   the   wiper   stalk   again   to   park   the  
w

iper   blades.
Replacement
  of   the   arms   must   be   done  
b

y   a   CITROËN   dealer   or   a   qualified  
w

orkshop.
Practical information

293
Towing the vehicle
The towing eye is installed in the boot under the   floor.
To
  gain   access   to   it:
F

o
pen the boot,
F
 
l
ift   the   floor   and   remove   it,
F
 
r
emove   the   towing   eye   from   its   housing.
General recommendations
Observe the legislation in force in your country.
E nsure   that   the   weight   of   the   towing   vehicle   is   higher   than   that   of   the   towed   vehicle.
The
  driver   must   remain   at   the   wheel   of   the   towed   vehicle   and   must   have   a   valid   driving   licence.
When
  towing   a   vehicle   with   all   four   wheels   on   the   ground,   always   use   an   approved   towing  
a

rm;   rope   and   straps   are   prohibited.
The
  towing   vehicle   must   move   off   gently.
When
  towing   a   vehicle   with   the   engine   off,   there   is   no   longer   any   power   assistance   for  
b

raking   or   steering.
In
  the   following   cases,   you   must   always   call   on   a   professional   recovery   service:
-
 
v
ehicle   broken   down   on   a   motor way   or   fast   road,
-
 
f
our-wheel   drive   vehicle,
-
 
w
hen   it   is   not   possible   to   put   the   gearbox   into   neutral,   unlock   the   steering,   or   release  
t

he   parking   brake,
-
 
t
owing   with   only   two   wheels   on   the   ground,
-
 
w
here   there   is   no   approved   towing   arm   available...
Procedure
 
for
 
having
 
your
 
vehicle
 
towed
 
or
 
for
 
towing
 
another   vehicle   using   the   towing   eye.
Access to the tools
7
Practical information

294
Towing another vehicle
F On  the   rear   bumper,   unclip   the   cover   by  p
ressing   at   the   bottom.
F
 
S
crew   the   towing   eye   in   fully.
F
 
I
nstall   the   towing   bar.
F
 
S
witch   on   the   hazard   warning   lamps   on  
b

oth   vehicles.
F
 
M
ove   off   gently,   drive   slowly   and   for   a   short  
di

stance.
F
 O
n
 
the
 
front
 
bumper,
 
unclip
 
the
 
cover
 
by
 p
ressing
 
on
 
the
 
left.
F
 
S

crew
 
the
 
towing
 
eye
 
in
 
fully.
F
 
I

nstall
 
the
 
towing
 
bar.
F
 
P

lace
 
the
 
gear
 
lever
 
in
 
neutral
 
(position
 
N
on
 
an
 
electronic
 
or
 
automatic
 
gearbox).
Towing your vehicle
Failure to observe this instruction could r esult   in   damage   to   certain   components  
(

braking,   transmission...)   and   the  
a

bsence   of   braking   assistance   the   next  
t

ime   the   engine   is   started.
F
 
U

nlock   the   steering   by   turning   the   key  
i

n
  the   ignition   one   notch   and   release   the  
par

king
 b
rake.
F
 
S

witch   on   the   hazard   warning   lamps   on  
b

oth   vehicles.
F
 
M

ove   off   gently,   drive   slowly   and   for   a   short  
di

stance.
Practical information