2013 SSANGYONG NEW ACTYON SPORTS key

02-58
You can register up to 2 transmission codes to the remote control key.
The receiver does not output the received code during registration.
The remote control key should be coded using the diagnostic device.
a.
b.
c.
1) Operating requirements
You should remove the ignition key.
2) Code registration requirement
You can register the code only using the diagnostic device.
3) Transmitter code registration
4. REKES Key Coding

02-598710-01
4) How to Code REKES Key
If you replace the REKES key or immobilizer key to new one, you should c\
ode the REKES key using the
diagnostic device. (maximum 5)Connect the diagnostic device to the vehilce and se lect the vehicle type and system (RK-STICS).
When the following screen is displayed, select 'REMOCON CODING'.
1.
Remove the remote control key from the ignition key box and press 'Next'\
. Press the door UNLOCK
(PANIC) button on the remote control key once (for approx. 2 seconds \
or longer).
2.

02-60
When you code newly purchased remote control key:When you lost the remote control key and purchase a new one, if you code\
only the newly
purchased one, the existing remote control key becomes unavailable. You must code the newly
purchased remote control key together with the existing one.
- The first key coding completion screen is displayed with beep sound as f\
ollows: Press 'Next' and
perform the second remote control key coding in the same way.
3.
When the second key coding is completed, the following screen is display\
ed. Finish the remote
control key coding by pressing 'Previous'.
4.
Exit the diagnostic screen, remove the device from the diagnostic connec\
tor and perform the
function test for the remote control key. If it does not work well, perf\
orm the above procedures again.
5.

02-610000-00
5) How to Register Transponder
Insert the ignition key into the key cylinder and turn it to the "ON" po\
sition.
Select the vehicle type and system (immobilizer) on the diagnosis program.
Select the Transponder registration menu and enter the password. (initi\
al value is "0000") Select "Next".
1.
2.
3.
Press "Next" with the first key in key box.
4.

02-62
Check the progress.
5.
If another key should be registered additionally, insert the second key \
into the key cylinder and press
"Next" within 10 seconds since the first transponder coding is complete.\
6.

02-64
6) Pin Arrangement of Diagnostic Connector
Diagnosis connector is installed at the lower driver side instrument pan\
el and it consists of 16 pins.
REKES key coding should be done using the diagnostic device. ▶Fuction For Each Terminal
Pin No. Function Pin No.Function
1 -9Air bag
2-1 0-
3 STICS "C1" 11TCU(6AT)
4 Ground 12SSPS Unit
5 Signal ground 13TCCU
6 CAN - HIGH 14CAN - LOW
7 GSL ECU 15STICS "B21"
8 -16Battery +
The REKES key coding is not performed by connecting the REKES coding ter\
minal (No. 15) of the
diagnostic connector to the jump wire between the ground terminals.
(possible only diagnostic device)

03-37010-06
ECUREKES keyDiagnostic connector
1. SYSTEM CONFIGURATION
1) Components and Locations
Immobilizer warning lamp in instrument panelImmobilizer unit

03-57010-06
Item Front view Rear view Internal structure
RKSTICS key
2. OVERVIEW
The Immobilizer System provides an additional theft deterrent to the vehicle in which it is installed and
prevents it from being started by unauthorized persons. The transponder integrated in the key and the
engine control unit has the same code. When the ignition key with the integrated transponder is turned to
the ON position, the ECU (Engine Control Unit) checks the crypto code of the key and, if correct, allows
your vehicle to start the engine.
Immobilizer unit
RKSTICS Key ▶