2013 SSANGYONG NEW ACTYON SPORTS key

02-32
▶Ignition Key Hole IlluminationThe ignition key hole illumination comes on when opening the driver's door or passenger's doo
r
while the ignition key is removed.
The ignition key hole illumination stays on for 10 seconds when closing \
the door after step (1).
The output stops when the ignition key is turned to the "ON" position.
The output stops when receiving the lock signal from the remote control key and entering armed
mode.
1.
2.
3.
4.
▶Key cylinder with key hole illumination With diesel and gasoline engine With diesel engine With gasoline engine
Without immobilizer
→With key hole
illumination With immobilizer
→With key hole
illumination With immobilizer
→Without key hole
illumination function

02-338710-01
▶STICS Circuit for Tail Lamp Auto Cut (Battery Saver)
▶Tail Lamp Auto Cut (Battery Saver) The tail lamp is turn on or off according to the operations of the tail \
lamp switch.
The tail lamp relay is turned off (auto cut) when opening and closing the driver's door afte
r
removing the ignition key without turning off the tail lamp.
The tail lamp relay is turned on when inserting the ignition key into th\
e ignition switch.
The tail lamp relay is turned off (auto cut) when opening and closing the driver's door while the
ignition key is removed and the tail lamp is turned on.
1.
2.
3.
4.

02-38
▶Door Lock/Unlock Control by Door Lock Switch
The door lock system outputs "LOCK" signal for 0.5 seconds when positioning the driver's o
r
passenger's door lock knob to the lock from unlock position.
The door lock system outputs "UNLOCK" signal fo r 0.5 seconds when positioning the driver's o
r
passenger's door lock knob to the unlock from lock position.
"LOCK" or "UNLOCK" by the door lock switch is ignored when outputting th\
e "LOCK" o
r
"UNLOCK" signal by other functions.
All door lock signals are "UNLOCK" for 0.5 seconds just for once when receiving the "LOCK"
signal within 0.5 seconds after closing the driver's or passenger's door while the ignition key is
removed.
1.
2.
3.
4.

02-40
▶Door Lock/Unlock Control by Remote Control Key
The door lock relay output is "ON" for 0.5 seconds when receiving the lo\
ck signal from the
remote control key.
The door unlock relay output is "ON" for 0.5 seconds when receiving the unlock signal from the
remote control key.
1.
2.

02-418710-01
The door lock system outputs "LOCK" when the vehicle speed maintains over 30 km/h.
However, it doesn't output "LOCK" when all doors are locked or failed.
If any of doors is unlocked after outputting "LOCK" in step 1, outputs "LOCK" up to 5 times
(except step (1)) at the interval of one second.
If any of doors is unlocked after 5 times of "LOCK" outputs, the door (driver's/passenger's/rear) is
regarded as "FAIL".
If the door that was regarded as fail is changed (UNLOCK to LOCK), it will be recognized as a
normal one.
If any door is regarded as FAIL, the auto door lock function does not work. (if it is occurred when
the vehicle speed is over 30 km/h, the auto door lock output does not occur even if the vehicle
speed falls below 30 km/h and accelerates again to over 30 km/h.) Nonetheless, the central
door lock function works properly.
When the system receives "UNLOCK" signal fr om a door switch, it outputs "LOCK" signals 5
times. If additional "LOCK" signal from another door switch is detected during \
the period, the
system outputs five "LOCK" signals 5 times for the switch.
The door lock system outputs "UNLOCK" automatically if the "LOCK" output conditions are
established by this function or the key is cycled (IGN=OFF) (even when there is no "LOCK"
output while the vehicle speed maintains over 30 km/h under lock conditi\
on).
(If the LOCK condition is established with the ignition switch ON, the system outputs UNLOCK
signal unconditionally when turning the ignition switch to OFF position.\
)
However, when the ignition key is turned to "OFF" position, the lock output conditions will be
cancelled.
The "FAIL" condition of the door will be erased when the ignition key is\
turned to "OFF" position.
1.
2.
3.
4.
5.
6.
7.
8.
▶Auto Door Lock
T2: 0.5 s
(*1) LOCK: Driver's & Passenger's & Rear door & = Lock

02-42
▶Auto Door Unlock (Crash Unlock: Automatic Door Unlock in Collision)
The air bag collision signal input cannot be accepted within 7 seconds after turning the ignition
key to "ON" position.
After this period, the door lock system outputs "UNLOCK" for all doors for 5 seconds from 40 ms
after receiving the air bag collision signal.
Even though the key is turned to "OFF" position during the output of "UNLOCK", the output
continues on for remaining period.
The function is erased when turning "OFF" the ignition switch.
1.
2.
3.
4.
Cautions for door lock/unlock control
The "Unlock" control by air bag signal prevails over any "LOCK" or "UNLOCK" control by othe
r
functions.
The "LOCK/UNLOCK" request by other functions will be ignored after/durin\
g the output o
f
"UNLOCK" by the air bag.
However, the door lock is controlled by other functions when the ignitio\
n switch is "OFF".
"LOCK" (or "UNLOCK") output is ignored if "LOCK" (or "UNLOCK") output is required while
performing the output of "LOCK" (or "UNLOCK").
(However, UNLOCK by air bag signal and operation by the remote control \
key are valid.)
If the door lock system outputs "LOCK" and "UNLOCK" simultaneously, only\
the "LOCK" output
can be activated.
1.
2.
3.
4.

02-438710-01
▶Time Lag Power Window Control
The power window relay output is "ON" when turning on the ignition switc\
h.
The power window relay output is "ON" for 30 seconds when turning off th\
e ignition switch.
The power window relay output is "OFF" when opening the driver's door or the passenger's
door.
The power window relay is turned "OFF" when receiving the remote control\
key lock signal
(armed mode) during its extended operation period of 30 seconds.
1.
2.
3.

02-458710-01
2) Description of Theft Deterrent Function
(1) Armed mode activation requirements
The "LOCK" output is "ON" when the "LOCK" signal is received from transmitter while the ignition
key is removed and all doors are closed.
The armed mode is activated when the door lock switch is locked (hazard warning flasher blink
twice).
The armed mode is still activated and the hazard warning flasher blink t\
wice when the
"LOCK" signal is received from the remote control key again in armed mod\
e.
When the "LOCK" signal is received from the remote control key while any of doors is not closed,
only the "LOCK" output can be done and then activates the armed ready mo\
de
(without theft deterrent horn and hazard warning flasher). At this moment, if the ignition key is
inserted or the door lock switch is unlocked, it cancels the armed mode and activates the normal
mode.
When the door is opened or the ignition key is not inserted into ignition switch within 30 seconds
after receiving "UNLOCK" signal from the remote control key, it outputs "LOCK" and then activates
armed mode (RELOCK operation). Also, at this moment, the system blinks hazard warning flashe
r
twice.
The armed mode will not be activated except above conditions.
Ex) The armed mode will not be activated when the door is locked by the\
ignition key.
a.
b.
c.
d.
e.