Page 378 of 751

03-6
3. FUNCTIONS OF IMMOBILIZER
The functions of the immobilizer are similar to that of the normal REKES key. But, there are the
immobilizer function that permits the engine to start only after confirming the encrypted coding.
The followings are common functions of the normal REKES key and the immobilizer.
Door Unlock and Panic Function
Breifly press (below 0.5 sec): Door unlock and
theft deterrent
mode deactivated
Press and hold (over 2 sec): Panic function
1. Door unlock (Briefly press)
If you send the door unlock signal using the
remote control key, with all the doors locked, the
door will be opened and the theft deterrent mode
will be deactivated. If the door coupled switch o
f
front room lamp is pressed, the lamp will come
on for 30 seconds. It will turn off immediately
after the lock button of the remote control is
pressed.
2. Panic function: activated in the theft deterrent mode
When pressing the door UNLOCK and PANIC button for approx.
2 seconds or longer, the warning alarm sounds and the hazard
warning lamp blinks for approx. 27 seconds.
The function is inactivated if any button of remote control is
pressed. ·
·
Breifly press (below 0.5 sec): Door lock and theft deterrent mode is activated
1. Door unlock (Briefly press)
If you press this button briefly, all doors and the tailgate are locked and the theft deterrent mode is
activated.When the theft deterrent mode is activated, the hazard warning flashers blink twice.LED flasher
Briefly press: blink once
Press and hold: blink twice
Door Lock
Page 380 of 751

03-8
4. START FUNCTION
1) Immobilizer Function
The immobilizer system prevents the vehicle theft by allowing only the authorized key to start the engine.
The transponder inside the key communicates with the immobilizer installed in the key box, and the
system permits the engine to start after confirming the encrypted coding from the engine ECU.
For the vehicle with the immobilizer, there can be a problem in starting the vehicle or the system
error:Immobilizer unit sends
encrypted code to
transponder (2)
Sends an encrypted signal to
unit as a response (3) Randomly transmitted code is changed to
an encrypted signal in immobilizer unit (4)
System compares signal from transponder and
encrypted signal in immobilizer unit (5)
When two or more immobilizer keys come into contact with (each) other(s).
When the key is close to any device sending or receiving electromagnetic fields or waves other
than Ssangyong products.
When the key is close to any electronic or electric devices such as lighting equipment, security
keys or security cards.
When the key is close to a magnetic or metal object or a battery. a.
b.
c.
d.
Immobilizer unitTransponder
Page 381 of 751

03-97010-06
Immobilizer and Warning Lamp ▶
This indicator comes on when the ignition key is
communicating with the engine control unit
(during engine starting) and goes out after
starting the engine.
When turning the ignition key to the "ON"
position, the ECU (engine control unit) transmits
the challenge message to the immobilizer unit.
(This is to verify whether the key is valid. If the
verification fails, it transmits re-verification signals
3 times for 2 seconds. If three re-verifications fail,
it stops verification and starts re-verification after
10 seconds.) (1)
ECUOnly when the two signals are identical, it recognizes the
key as the authorized one and transmits the positive
message to the ECU. (6)
The ECU enable the engine to be started. (7)
Do not drop or shock to the transponder in the key as it may be damaged.
With a damaged transponder, the engine cannot be started.
When you erase the code or register an extra key, please attend on the site.
In any cases, the immobilizer system can not be removed from the vehicle. If you attempt to
remove it and damage the system, starting will be impossible, so never attempt to remove,
damage or modify it.
The remote engine starter cannot be installed to the vehicle equipped with the immobilizer system. ·
·
·
·
·ON: In communication
Blinks twice at one second intervals: Immobilizer
system fault
Blinks once at 2 second intervals: Immobilizer unit
not coded
The immobilizer indicator does not come on if
the communication time between immobilizer
key and ECU is too short.
Instrument
panel
Page 383 of 751
03-117010-06
5. REKES OPERATION LOGIC
1) Remote Door Lock
When briefly pressing the door lock switch on the remote control key for less than 0.5 seconds, all
doors are locked.
The system outputs the "LOCK" signal immediately after receiving the door lock message from the
remote control key. If the vehicle is locked while all doors including engine hood are closed, the theft
deterrent mode is activated (hazard warning lamps are blinking twice). 1.
2.
Page 384 of 751
03-12
2) Door Unlock
When briefly pressing the door unlock switch on the remote control key for less than 0.5 seconds, all
doors are unlocked.
When receiving the DOOR UNLOCK message from the remote control key, the door unlock relay is
turned on for 0.5 seconds.
The hazard warning lamps blink once only when all the doors unlocked successfuly. 1.
2.
3.
Page 385 of 751
03-137010-06
3) Remote Panic
When pressing and holding the PANIC button on the remote control key for more than 2 seconds,
the panic function is activated.
The vehicle activates the panic alarm by using the horn for 27 seconds when receiving the panic
message from the remote control key. 1.
2.
Page 403 of 751

04-20
3. WARNING LIGHTS AND INDICATORS
ESP OFF Indicator
This lamp comes on when
pressing the "ESP OFF" switch or
the ESP system is defective.
When the ESP system is
activated, this lamp blinks and a
chime sounds.
Immobilizer Indicator
This indicator comes on
when the ignition key is
communicating with the
engine control unit for
approx. 0.5 seconds.Glow Indicator
When the ignition key is turned
ON, this indicator lamp comes on
and the combustion chamber is
warmed up. In the vehicle
equipped with direct injection type
engine, this indicator may come
on very shortly or may not come
on.
Fog Lamp / Headlamp
High Beam Indicator
This lamp comes on when
the fog lamp or high beam
headlamp operates to
indicate the operating
status.Engine Oil Pressure Warning
Light
This lamp comes on if there is any
fault in the engine oil system and
goes off when a certain amount of
time has elapsed after turning ON
the ignition switch.
Door ajar warning
light
This light comes on
when a door or
tailgate is either
opened or not closed
completely.Brake warning light
This warning light comes on
and warning buzzer sounds
when the parking brake is
applied and/or the brake fluid
level is lower than specified
level.Seat belt warning lamp
The seat belt warning light comes on and
the seat belt warning chime sounds for 6
seconds when the ignition switch is
turned to "ON" position unless the
driver's seat belt is securely fastened.
This reminding operation stops when the
driver fastens the seat belt.
Engine Coolant Overheat
Warning Light
When the coolant temperature is
abnormally hot (over 120℃), this
warning light blinks and a warning
buzzer sounds at 1 Hz. (check
cooling system)
SSPS warning light
This warning light comes on when
the SSPS system is defective.
When this warning light comes
on, the steerability becomes
heavier.
Page 405 of 751
04-22
How to enter self-diagnosis mode ▶
Turn the ignition ON with the TRIP switch pressed.
Press and hold the TRIP switch for 5 to 10 sec. with the ignition ON.
Press and hold the TRIP switch for less than 10 sec. and then cycle the switch between ON and
OFF 5 times within 3 sec.
Confirm that the self-diagnosis mode is activated through the instrument cluster. 1.
2.
3.
4.
4. SELF-DIAGNOSIS CHECK
Self-diagnosis OFF ▶
If the engine speed increases to 396 rpm or more while the engine is cranking or the ignition key is
turned OFF in self-diagnosis mode, the self-diagnosis mode is turned OFF automatically.
Operating process ▶
Speed gauge: changes from 0 to 220 km
RPM gauge: changes from 0 to 6,000 rpm
Fuel gauge: changes from E to F
Temperature gauge: changes from C to H
Warning/Indicator lamps: All indicator/warning lamps controlled by MICOM are turned ON.
Dimming: Illuminates at the highest lighting level.
LCD display: All elements are activated. 1.
2.
3.
4.
5.
6.
7.