2013 SSANGYONG NEW ACTYON SPORTS battery

07-51452-01
1. DESCRIPTION AND OPERATION
1) Battey
The sealed battery is standard on all cars. There are no vent plugs in the cover.
The battery is completely sealed, except for two small vent holes in the sides.
These vent holes allow the small amount of gas produced in the battery to escape.
The battery has the following advantages over conventional batteries:
No water addition for the life of the battery.
Overcharge protection. If too much voltage is applied to the battery, it will not accept as much current
as a conventional battery.
In a conventional battery, the excess voltage will still try to charge the battery, leading
to gassing, which causes liquid loss.
Not as liable to self-discharge as a conventional battery. This is particularly important when a battery
is left standing for long periods of time.
More power available in a lighter, smaller case. ·
·
·
·
The battery has three major functions in the electrical system.
First, the battery provides a source of energy for cranking the engine.
Second, the battery acts as a voltage stabilizer for the electrical system. Finally, the battery
can, for a limited time, provide energy when the electrical demand exceeds the output of the generator.
2) Ratings
<0068004700890088009b009b008c009900a00047008f0088009a0047009b009e0096004700990088009b00900095008e009a00610047004f005800500047008800470099008c009a008c0099009d008c0047008a008800970088008a0090009b00a0004700
990088009b00900095008e0047008b008c009a0090008e0095>ated at 27°C(80°F), which is the
time a fully charged battery will provide 25 amperes of current flow at or above 10.5 volts (2) a cold
cranking am
p rating determined under testing at -18°C(0°F), which indicates the cranking load
capacity. ▶
(1)Reserve Capacity
The reserve capacity (RC) is the maximum length of time it is possible to travel at night with the minimum
electrical load and no generator output. Expressed in minutes, the RC rating is the time required for a
fully charged battery, at a temperature of 27°C(80°F) and being discharged at a current of 25
amperes, to reach a terminal voltage of 10.5 volts.

07-6
(2) Cold Cranking Amperage
The cold cranking amperage test is expressed at a battery temperature of -18°C(0°F).
The current rating is the minimum amperage, which must be maintained by the battery for 30 seconds at
the specified temperature, while meeting a minimum voltage requirement of 7.2 volts.
This rating is a measure of cold cranking capacity.
The battery is not designed to last indefinitely. However, with proper care, the battery will provide many
years of service. If the battery tests well, but fails to perform satisfactorily in service for no apparent
reason, the following factors may point to the cause of the trouble:
Vehicle accessories are left on overnight.
Slow average driving speeds are used for short periods.
The vehicle's electrical load is more than the generator output, particularly with the addition o
f
aftermarket equipment.
Defects in the charging system, such as electrical shorts, a slipping generator belt, a faulty generator,
or a faulty voltage regulator.
Battery abuse, including failure to keep the battery cable terminals clean and tight or a loose battery
hold-down clamp.
Mechanical problems in the electrical system, such as shorted or pinched wires. ·
·
·
·
·
·
3) Charging Time Required
The time required to charge a battery will vary depending upon the following factors:
Size of Battery - A Completely discharged large heavy-duty battery required more than twice the
recharging time as a completely discharged small passenger car battery. ▶
<007b008c00940097008c00990088009b009c0099008c00470054004700680047009300960095008e008c00990047009b00900094008c0047009e00900093009300470089008c00470095008c008c008b008c008b0047009b00960047008a008f0088009900
8e008c00470088009500a0004700890088009b009b008c0099>y at -18°C(0°F) than at
27°C(80°F).
When a fast charger is connected to a cold battery, the current accepted by the battery will be very
low at first.
The battery will accept a higher current rate as the battery warms. ▶
Charger Capacity - A charger which can supply only 5 amperes will require a much longer charging
period than a charger that can supply 30 amperes or more. ▶
State-of-Charge - A completely discharged battery requires more than twice as much charge as a
onehalf charged battery.
Because the electrolyte is nearly pure water and a poor conductor in a completely discharged
battery, the current accepted by the battery is very low at first. Later, as the charging current causes
the electrolyte acid content to increase, the charging current will likewise increase. ▶

07-71452-01
4) Charging a Completely Discharged Battery (Off the Vehicle)
Unless this procedure is properly followed, a perfectly good battery may be needlessly replaced.
The following procedure should be used to recharge a completely discharged battery:
Measure the voltage at the battery terminals with an accurate voltmeter.
If the reading is below 10 volts, the charge current will be very low, and it could take some
time before the battery accepts the current in excess of a few milliamperes.
Refer to "Charging Time Required" in this section, which focuses on the factors affecting both the
charging time required. Such low current may not be detectable on ammeters available in the field.
Set the battery charger on the high setting. 1.
2.
Continue to charge the battery until the charge current is measurable. Battery chargers vary in the
amount of voltage and current provided. The time required for the battery to accept a measurable
charger current at various voltages may be as follows: 3.
If the charge current is not measurable at the end of the above charging times, the battery
should be replaced.
If the charge current is measurable during the charging time, the battery is good, and charging
should be completed in the normal manner. ·
·
If the charge current is still not measurable after using the charging time calculated by the above
method, the battery should be replaced. ·
It is important to remember that a completely discharged battery must be recharged for a sufficient
number of ampere hours (AH) to restore the battery to a usable state.

07-8
5) Jump Starting Procedure
Position the vehicle with the charged battery so that the jumper cables will reach from the charged
battery to the battery that requires charging.
Turn off the ignition, all the lights, and all the electrical loads in both vehicles.
Leave the hazard flasher on if jump starting where there may be other traffic and any other lights
needed for the work area.
Apply the parking brake firmly in both vehicles. 1.
2.
3.
4.
Shift an automatic transmission to PARK. 5.
Clamp one end of the first jumper cable to the positive terminal on the booster battery. Make sure it
does not touch any other metal parts.
Clamp the other end of the same cable to the positive terminal on the discharged battery. Never
connect the other end to the negative terminal of the discharged battery. 6.
7.
Clamp one end of the second cable to the negative terminal of the booster battery.
Make the final connection to a solid engine ground, such as the engine lift bracket at least 450
millimeters (18 inches) from the discharged battery.
Start the engine of the vehicle with the good battery.
Run the engine at a moderate speed for several minutes.
Then start the engine of the vehicle with the discharged battery.
Remove the jumper cables by reversing the above sequence exactly, removing the negative cable
from the vehicle with the discharged battery first.
While removing each clamp, take care that it does not touch any other metal while the other end
remains attached. 8.
9.
10.
11.
12.In order to avoid damaging the vehicle make sure the cables are not on or near pulleys, fans, or
other parts that will move when the engine starts.
In order to avoid injury, do not use cables that have loose or missing insulation.

07-91452-01
6) Alternator
Alternators are equipped with internal regulators.
Unlike three-wire generators, the alternator may be used with only two connections: battery positive and
an "D+" terminal to the charge indicator lamp.
As with other charging systems, the charge indicator lamp lights when the ignition switch is turned to
RUN, and goes out when the engine is running.
If the charge idicator is on with the engine running, a charging system defect is indicated. This indicato
r
light will glow at full brilliance for several kinds of defects as well as when the system voltage is too high
or too low.
The regulator voltage setting varies with temperature and limits the system voltage by controlling roto
r
field current.
Achieve correct average field current for proper system voltage control by varying the on-off time. At high
speeds, the on-time may be 10 percent and the off-time 90 percent.
At low speeds, with high electrical loads, the on-time may be 90 percent and the off-time 10 percent.
7) Charging System
Generators use a new type of regulator that incorporates a diode trio.
A Delta stator, a rectifier bridge, and a rotor with slip rings and brushes are electrically similar
to earlier generators.
A conventional pulley and fan are used.
There is no test hole.
8) Starter
Wound field starter motors have pole pieces, arranged around the armature, which are energized by
wound field coils.
Enclosed shift lever cranking motors have the shift lever mechanism and the solenoid plunger enclosed
in the drive housing, protecting them from exposure to dirt, icy conditions, and splashes.
In the basic circuit, solenoid windings are energized when the switch is closed.
The resulting plunger and shift lever movement causes the pinion to engage the engine flywheel ring
gear.
The solenoid main contacts close. Cranking then takes place.
When the engine starts, pinion overrun protects the armature from excessive speed until the switch is
opened, at which time the return spring causes the pinion to disengage.
To prevent excessive overrun, the switch should be released immediately after the engine starts.

07-10
9) Starting System
The engine electrical system includes the battery, the ignition, the starter, the generator, and all the
related wiring.
Diagnostic tables will aid in troubleshooting system faults. When a fault is traced to a particula
r
component, refer to that component section of the service manual.
The starting system circuit consists of the battery, the starter motor, the ignition switch, and all the related
electrical wiring.
All of these components are connected electrically.

02-338710-01
▶STICS Circuit for Tail Lamp Auto Cut (Battery Saver)
▶Tail Lamp Auto Cut (Battery Saver) The tail lamp is turn on or off according to the operations of the tail \
lamp switch.
The tail lamp relay is turned off (auto cut) when opening and closing the driver's door afte
r
removing the ignition key without turning off the tail lamp.
The tail lamp relay is turned on when inserting the ignition key into th\
e ignition switch.
The tail lamp relay is turned off (auto cut) when opening and closing the driver's door while the
ignition key is removed and the tail lamp is turned on.
1.
2.
3.
4.

02-478710-01
(7) Operation when warning is cancelled
The theft deterrent horn and hazard warning flasher is activated when fi\
tting the battery in armed mode. (The
same operation as when alarm condition is met in armed mode is performed\
.)PANIC Warning
▶
The PANIC warning output is "ON" for 27 seconds using the horn and hazar\
d warning flasher,
when receiving the PANIC signal from the remote control key.
The PANIC warning output is "OFF" when pressing any button on the remote\
control key during
PANIC warning.
The followings are about the theft deterrent warnings.
1.
2.
3.
The theft deterrent warning is deactivated when receiving PANIC signal f\
rom the remote
control key during theft deterrent warning.
The theft deterrent warning output is "ON" when the theft deterrent cond\
itions are
established during PANIC warning (PANIC output is "OFF").
The PANIC warning output is "ON" when receiving the PANIC signal from th\
e remote control
key in Armed Ready / Armed / Warning Comp letion / Relock Ready mode (maintaining the
theft deterrent mode).
a.
b.
c.
This function operates only in armed mode.
4.
Removed Normal Armed Warning Remark
Normal O
RELOCK operation:
When the door is not opened
or the ignition key is not
inserted into ignition switch
for 30 seconds after
receiving "UNLOCK" signal,
outputs "LOCK" and then
activates armed mode
Armed Ready
O
Armed O
Warning O
Warning Completion O OO
RELOCK Ready O
Installed