2013 Lancia Ypsilon Owner handbook (in English)

When using or parking the car for a long time in
the mountains or cold areas, it is advisable to
refuel using locally available diesel. In this case, it
is also advisable to keep the tank over 50% full.
For diesel engines, use only diesel fuel
for motor vehicles in accordance with
EN590 European specifications. The
use of other products or mixtures may damage
the engine beyond repair and consequently
invalidate the warranty, depending on the
damage caused. If you accidentally refuel with
another type of fuel, do not start the engine,
and drain the fuel tank. If the engine has been
run, even for only a very short time, you will
need to have the entire fuel system emptied in
addition to the tank.
REFUELLING CAPACITY
To fill the tank completely, top up twice after the
pump switches off. Further top-ups could cause
faults in the fuel feeding system.
REFUELLING PROCEDURE FOR VERSIONS
EQUIPPED WITH FUEL TANK PLUG
(for versions/markets, where provided)
Refuel as follows:
❒open the flap A fig. 87 pulling it outwards;
❒keep the plug B still, insert the ignition key in
the lock and turn it anticlockwise;
❒Turn the plug anticlockwise and remove it.The plug has a device C fig. 87 that attaches it to
the flap so that it cannot be lost. When refilling,
attach the plug to the flap, as shown.
After refuelling, fit the plug B fig. 87 (complete
with key) and turn it clockwise until it clicks once
or more. Turn the key clockwise and remove it.
Close the flap A.
The sealing may cause a slight pressure increase in
the tank. A little breathing off, while unscrewing
the plug or introducing the gun in the versions
equipped with "Smart Fuel", is therefore
absolutely normal.
fig. 87
L0F0240
125GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

REFUELLING PROCEDURE FOR VERSIONS
EQUIPPED WITH "SMART FUEL" SYSTEM
"Smart Fuel" is a device integrated with the end
of the fuel filler pipe which opens and recloses
automatically when the fuel delivery gun is
introduced/removed. "Smart Fuel" is provided
with an inhibiter which prevents refuelling with
incorrect fuel.
The refuelling procedure described here is
illustrated on label B fig. 88, which is applied
inside the fuel flap. The label also indicates the
fuel type (UNLEADED FUEL=petrol,
DIESEL=diesel fuel).
To refuel proceed as follows:
❒open the flap A fig. 88 pulling it outwards;
❒introduce the dispenser in the filler and refuel;
❒at the end of refuelling, before removing the
dispenser, wait for at least 10 in order for the
fuel to flow inside the tank;
❒then remove the dispenser from the filler and
close the flap A.
Flap A fig. 88 is provided with a dust cowl C
which prevents deposits of impurities and dust at
the end of the filler when the flap is closed.
fig. 88
L0F0085
126GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Emergency refuelling (only for versions
equipped with "Smart Fuel")
If there is no fuel in the car or the supply circuit is
completely empty, proceed as follows to
reintroduce fuel in the tank:❒open the luggage compartment and take the
adapter B located in the tool box (versions
equipped with space-saver wheel - for
versions/markets, where provided) fig. 89 or in
the Fix&Go Automatic container (versions
equipped with Fix&Go Automatic) fig. 90;
❒open the flap A pulling it outwards;
❒insert adapter B in the filler as shown in fig. 91
and refuel;
❒after refuelling, remove the adapter and close
the flap;
❒reintroduce the adapter in the box and put this
back in the luggage compartment.
fig. 89
L0F0242
fig. 90
L0F0241
fig. 91
L0F0086
127GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

IMPORTANT INFORMATION FOR VERSIONS
EQUIPPED WITH "Smart Fuel"
WARNING
At the end of the filler do not apply
any object/plug which is not provided
for for the car. The use of non compliant
objects/plugs could cause a pressure
increase inside the tank, generating
dangerous situations.
WARNING
Do not bring naked flames or lit
cigarettes near to the fuel filler: fire
risk. Keep your face away from the fuel filler
to prevent breathing in harmful vapours.
IMPORTANT If the filler compartment is washed
with a high pressure jet, keep it at a distance of
at least 20 cm.
PROTECTING THE ENVIRONMENTThe following devices are used for reducing petrol
fuel engine emissions: catalytic converter, oxygen
sensors and evaporation control system
Do not let the engine run, even for a test, with one
or more spark plugs disconnected.
The following devices are used for reducing diesel
fuel engine emissions: oxidising catalytic
converter, exhaust gas recirculation system (EGR)
and particulate filter (DPF).
DIESEL PARTICULATE FILTER (DPF)
(for versions/markets, where provided)
The Diesel Particulate Filter is a mechanical filter,
integral with the exhaust system, that physically
traps particulates present in the exhaust gases
of Diesel engines.
The diesel particulate filter is needed to eliminate
almost all particulates in compliance with current
/ future legislation.
During normal use of the vehicle, the engine
control unit records a set of data (e.g. travel time,
type of route, temperatures, etc.) and it will then
calculate how much particulate has been trapped
by the filter.
Since this filter physically traps particulate, it
should be regenerated (cleaned) at regular
intervals by burning the carbon particles.
128GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

The regeneration procedure is controlled
automatically by the engine management control
unit according to the filter conditions and car
use conditions.
There may be a limited increase in the engine idle
speed during the regeneration, a limited increase
in fumes and high temperatures at the exhaust.
These are not faults; they do not impair normal
vehicle performance or damage the environment.
If the dedicated message is displayed, refer to
paragraph "Warning lights and messages".
WARNING
During normal service, the catalytic
converter and the diesel particulate
filter (DPF) reach high temperatures. Do not
therefore park the car over inflammable
materials (grass, dry leaves, pine needles,
etc.): fire hazard.
129GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

SAFETY
SEAT BELTSUSING THE SEAT BELTS
The belt should be worn keeping the torso straight
and rested against the backrest.
To fasten the seat belts, hold the tongue A fig. 92
and insert it into the buckle B, until the locking
click is heard. On removal, if it jams, let it rewind
for a short stretch, then pull it out again without
jerking.To unfasten the seat belts, press button C. Guide
the seat belt with your hand while it is rewinding,
to prevent it from twisting. Through the reel,
the belt automatically adapts to the body of the
passenger wearing it, allowing freedom of
movement.
WARNING
Never press button C fig. 92 when
travelling.
The reel may lock when the car is parked on a
steep slope: this is perfectly normal. Furthermore,
the reel mechanism locks the belt if it is pulled
sharply or in the event of sudden braking,
collisions and high-speed bends.
The rear seat is fitted with inertia seat belts with
three anchor points and a reel. Fasten the rear seat
belts as shown in fig. 93 (4-seater versions) or
(5-seater versions) fig. 94.
fig. 92
L0F0059
130
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

WARNING
Remember that in the event of a
violent collision, back seat
passengers not wearing seat belts also
represent a serious danger for the front seat
passengers.IMPORTANT When putting the back seats back to
their normal position, make sure the seat belts
are positioned so they are ready to use.
WARNING
The rear central seat belt is provided
with a service buckle fig. 95. Do not
use the seat belt with the service buckle not
fastened. In the case there is a high risk of
injuries or death in the event of an accident.
Before using the belt, always make sure
that the service buckle is correctly fastened.
fig. 93
L0F0060
fig. 94
L0F0261
fig. 95
L0F0260
131GETTING TO KNOW
YOUR CARSAFETYSTARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

S.B.R. SYSTEM (Seat Belt Reminder)This system consists of a device which, in
conjunction with the
warning light flashing on
the instrument panel and an intermittent acoustic
signal, warns the driver and front passenger if
their seat belts have not been fastened.
There is also a reminder above the internal rear
view mirror fig. 96 (4-seater versions), or fig. 97
(5-seater versions) which advises front and rear
seat passengers, by means of a visual and acoustic
indication, that their seat belts are not fastened.
For versions/markets where provided, contact
a Lancia Dealership should you wish to
permanently deactivate the SBR system. The
system can only be reactivated through the display
Setup Menu (see “Knowing your car” section).
The warning lights may be red or green and
operate as follows:
4-seater versions
❒1 = front left seat (driver status for left-hand
drive versions);
❒2 = rear left seat (passenger);
❒3 = rear right seat (passenger);
❒4 = front right seat (passenger status for
left-hand drive versions).
fig. 96 - 4-seater versions
L0F0225
132
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX