2013 AUDI Q5 engine

102 Hybrid
Tips for Driving Efficiently with your Hybrid
Applies to vehicles: with hybrid drive
Driving situa- Conditions Vehicle behavior
tions
- Shift into the D position.
In the D position, the hybrid system adapts
Starting from a -
Release the brake pedal. to the driving situation by automatically
stop -
Only press moderately on the ac- switching between the combustion engine
and electric drive types or by combining
celerator pedal.
them.
- Ca utious dr iv ing and reserved ac-
The kinetic energy of the vehicle is used to
ce leration . move the vehicle.
Constant driv-
ing and coasting -
Release the acce lerator pedal When you release the acce lerator pedal en -
early and entirely. ti rely, the combustion engine turns off au-
(gliding)
tomatically and is disengaged. The vehicle
glides without being propelled.
- Brake early and even ly with short The electric motor brakes the vehicle . By
Energy recovery pedal
movements. doing this, a large amount of the
kinetic
energy is recovered and may be stored in
( recuperation)
the high voltage battery in the form of
electric energy.
- Reserved acceleration and early The kinet ic energy of the vehicle is used to
and even braking w ith short pedal move the vehicle.
movements .
Driving in city -
Use the
la• I button sparing ly. The battery drains quickly when the laVI
button is turned on, which can increase
traffic
fuel consumption because electric driving
is given priority, even if driving with the
combustion engine on would be more effi-
cient .
- Intentionally take your foot off When you release the acce lerator pedal en-
of the gas pedal to allow for ti rely, the combustion engine turns off au-
lengthy coasting . tomatically and is disengaged. The vehicle
glides without being propelled.
Driv ing on high- -
Reduce the vehicle speed by re-Fuel consumption can be reduced by coast-
ways and ex-l
eas ing the accelerator peda l and mg.
pressways not by
braking.
- Avoid vehicle speeds above ajp-
It is possible to coast up to a veh icle speed
proximately 99 mph (160 km/h) . of approximately 99 mph (160 km/h).
- Use the S selector lever position A sporty driving sty le increases fuel con -
and tiptron ic mode sparingly. sumption.

Hybrid 103
Driving situa -Condition s Vehicle behavior
ti ons
- Do not r un the combustion en- The temperature of the comb ustion eng ine
gine wh ile the vehicle is parked to rises very slowly and the fuel consumption
warm the engine . increases considerably.
- Use the rear w indow/exter ior This conserves the energy in the h igh vo lt-
Driv ing in cold mirro
r defroster and the seat heat- age battery so that it is ava ilab le to r un the
weather i
ng s par ingly. vehicl e in ele ct ric mode .
- Park the vehicle in a garage over-
This reduces ex pos ure of the hig h voltage
night.
Energy flow display
Applies to vehicles: with hybrid dr ive
F ig. 110 Instrument cluster: e nergy flow disp lay
The energy flow o f the hybrid system is shown
i n the instrument cluster display and in the
M MI disp lay. The image is animated in the
MMI disp lay.
Image in the instrument cluster display
.. Pres s the !RESET I but ton in the w indshield
wipe r lever repeate dly until the e ne rgy flow
di splay
c::> fig . 110 appears .
Component
@Propshaft
Color
orange
gray
green
ora nge
g ra y battery to co
ld temperat ures . The required
temperature range for the high voltage
battery will then be reached more quick ly
after you start driving.
Fig. 1 11 M MI d isp lay: energy flow display
Image in the MMI display
.,. Select: I ME NU I fu ncti on bu tton > Hybrid
cont ro l button c::> fig . 111.
Meaning
The combustion engine Is running
The combust io n engin e is off
E lectric driving/recuperating
D riving w ith th e combus tion en gin e
Driving with the combustion engine and electric
motor (boost)
Vehi cle s ta tio nary/ rolling in the N sele ctor lever
p osition

104 Hybrid
@ High voltage battery green High voltage battery charge level
green (animated High voltage battery is charging
@ Movement arrow in MMI)
gray
green
orange
---.. ,
green-orange
@ Movement arrow g
reen
@ Tips
The Energy flow display will not shown in
the MMI display when the reverse gear is engaged, due to safety reasons .
Consumption display
Applies to vehicles: with hybrid drive
Fig. 1 12 MM! display: consumpt ion disp lay
The consumption display shows the average
energy consumption and the recuperat ion
quantity in S minute interva ls.
Call ing up th e co nsumption displa y
.. Se lect: I MENU I function button > H ybrid
control button .
.. Turn the control knob counter-clockwise.
Res etting the con sumption display
.. Se lect: I MENU I function button> H ybrid
control button.
.. Turn the contro l knob to
Reset consump-
tion stat istics.
The o range bars show the average cons ump­
tion and the green bars show the recuperation
quantity . Each bar represents a measured S Vehicle is not in drive ready mode
Electric driving
Driving with the combustion engine
Driving w ith the combust ion engine and electric
motor (boost)
Recuperating
minute interval. The d isplay
covers a 60 mi ­
nute time period.
The bar with the white border on the outer right shows the current ave rage consumption
or the cur ren t recupera tion quan tity. After 5
minutes, th is bar travels a step to the left and
a new bar appears in the outer right.
T he filled bars show the values fo r the current
drive cycle. Once the ignition is switc hed off
and on again, all o f the p revio us ba rs a re d is ­
played as not filled and new filled bars appear
on the right . This is so that the values from
the previous tr ips and the current trip can be
compared visually.
Vehicle tool kit and tire repair set
Applies to vehicles: with hybrid drive
Fig. 11 3 Luggage compartment: vehicle tool bag and
tire repair se t
The vehicle tool k it is found under a cove r in
the cargo floo r<=>
fig . 113 @. The tire repair
set (Tire Mobility System) is found in the stor­
age compartment in the r ight s ide tr im panel
® · ~

Additional information about the vehicle tool kit may be found under
c::> page 269 and
about the tire repa ir set under
c::> page 2 72 .
(D Tips
The right storage compartment in the lug­
gage compartment and its contents must
always be kept in the vehicle. The veh icle
m ust not be operated w ithout the tire re­
pa ir set.
Charging the batteries
Applies to vehicles: with hybrid drive
The vehicle is equipped with two 12 volt bat ­
ter ies and a h igh voltage battery.
If the
12 volt batter ies are dead, they may be
charged with a charger or the vehicle may be
jump started with assistance from another ve­
hicle in the same way as a conventional vehi­
cle .
The same applies to the high voltage battery
if it is d ischarged . However, in this case, the
charg ing process is accompanied w ith mes­
sages in the inst rument cluste r display. The
i gnit ion m ust be switched on and all unneces­
sary electric components m ust be turned off.
The connections in the engine compartment
are used for both charging and jump starting
c::> page 245 or c::> page 284.
Vehicle not ready to start. See owner's
manual
This message appears if the high voltage bat­
tery charge level is too low. The vehicle can no
l onge r be started with its own power. The
high voltage battery must be charged with a
charger or the vehicle must be jump started
with the aid of another vehicle.
Afte r the connecting the cha rger or jumper ca­
b les, the ignition must be turned off for ap­
proximately two minutes and then turned on
again. After no more than one m inute, one of
the following indicator lights turns on in the instrument cluster d isp lay. Hybrid 105
II Charging battery. Please wait ...
If
the indicator light turns on and this mes­
sage appears, the high voltage battery is
charging or the vehicle is being jump started
with assistance from another vehicle.
If the 12 vo lt batteries are dead, the -
indicator light turns on. The charging proce­
dure takes longer in this case because the
12
volt batteries are charged first. The procedure
goes faster with the ignition switched off.
Vehicle ready to start.
This message appears if the charging proce­
dure was successfu l. The vehicle may be start­
ed again.
Battery could not be charged enough to
start vehicle.
T his message appears if the charging proce­
dure was not successful or it was interrupted.
This may happen if the charger or the battery
in the veh icle that is assist ing is too weak.
If
the vehicle cannot be started, see an author­
ized repa ir facility for assistance .
(D Tips
- The charger should deliver a current of at
least
30 A. Otherwise charging the high
voltage battery will take considerably longer. A current between
50 A and 70 A
is ideal.
- The ve hicle that is assist ing should be
somewhat within the same vehicle class
when jump starting a vehicle. A smaller
vehicle's battery may be drained.
- After approximately
30 minutes, the
c harging procedure ends because the ig­
nition is automatically turned off.
If you
would like to continue to charge the bat­
tery, turn the ignition on again.

120 Audi drive select
Audi drive select
Driving settings
Introduction
App lies to vehicles: with Audi drive select
Drive select provides the possib ility to exper i­
e nce diffe ren t types of vehi cle sett ings in o ne
ve hicl e. For ins tance, us ing t he three
Com­
fort , Auto and Dynamic modes, the driver can
switch from a sporty to a comfortab le drivi ng
mode with the press of a b utton.
A ddit ionally, in veh icles wi th MM I*, the vehi ­
cle setup for
Individual* mode can be c us­
tom ized by you. This makes it possib le to
comb ine settings such as a sporty engine tun ­
ing with comfortable steering.
A WARNING
Improper use of the drive select can cause
co llisions, other accide nts and ser ious per­
sonal injury.
Description
App lies to vehicles: with Audi drive select
The vehicle setup in each mode depends on
the veh icle's features . However, the engin e,
automa tic t ransmissio n and steeri ng a re a l­
ways involved.
Engine and automatic transmission
Depending on the mode , the e ng ine and the
automatic t ransm ission respond quicke r or i n
a more ba la nced manne r to a cce le rator pedal
move ments. In t he sporty dynam ic mode, the
a ut om at ic t ra nsmissio n shifts at h igher R PMs.
Steering
The steering adapts in terms of stee ring effort
and steering ra tios . Ind irect steer ing that
moves easi ly, l ike the stee rin g in comfort
mode, is best su ite d t o long dr ive s on a high­
way. In co ntr ast, dynam ic mo de p rov ides
sporty, direct steering .
T he fo llow ing applies to vehicles with dynam ic
steer ing*: the stee ring ratio changes based on
ve hicl e spee d in order to maint ain op timum steering effort
for the drive r at all times . This
sets the stee ring to be less sens itive at higher
speeds in order to provide improved vehicle
control. At reduced speeds, however, steer ing
is more d irect in order to keep the steering ef­
fort as minima l as poss ible when the driver is
mane uveri ng the veh icle. At low and ave rage
speeds, dynamic steering addit iona lly pro­
vides more respon sive stee rin g pe rforma nce.
Adaptive dampers*
The adaptive dampers* use se nsors to record
informa tion regard ing steer ing movemen ts,
braking and acceleration o perations by the
drive r, road surfac e, d riv in g speed, and load.
T his makes it poss ible to adapt damp ing to
the driving si tua tion v irtu ally in real t ime.
Dr ive sele ct also makes i t possib le to sa tisfy
t h e desire fo r spo rty suspension ( Dynamic)
and comfortab le suspension (Comfort) with ­
o ut giving up ba lanced tuning (Auto) .
Adaptive cruise control*
The be havior when accelera ting can be adju st­
ed from comforta ble to sporty, depending on
the d rive select mode . Adaptive cr uise contro l
also responds to the driv ing behavior of the
vehicle ahead in a more conservative or spo rty
manner.
(D Tips
- In some mo dels, t he maximum vehicle
speed can only be reached in the
Auto
and Dynamic mo des.
- Selecting the
Dynamic mode resu lts in
sporty shifting cha racte ristics. The S
gear position engages aut omatically.
- In vehicles that have dynamic stee ring *,
operating noise is heard when start ing or
stopping the e ngine. This does not indi­
cate a problem .

Selecting the driving mode
Applies to vehicles: with Audi drive select
You con choose between Comf ort , Aut o, Dy ­
namic
and Indi vidu al* modes .
drive I I a,. selact ~
Fig. 130 Ce nter co nsole: Con tro l for dr ive selec t
Fig. 131 MM I* : A udi drive se lect
,.. To set the mode, press the 1til.t button
9fig. 130 multiple times until the desired
mode is displayed in the instrument cluster.
Or
Adjusting the Individual mode
Appl ies to vehicles: with Audi drive select and MMI
Audi drive sele ct 121
,.. In the MMI*, select: ICARI function button >
Co mfo rt , Au to , D ynamic or Indi vidual *.
In vehicles without MMI*, the r.'i:.1 button is
fo und underneath the se lector lever .
You can change the driving mode when the ve­ hicle is stationary or whi le driving. If traffic
permits, after changing modes, briefly take
you r foot off the acce le rator pedal so that the
recently selected mode is a lso activated for
the engine and transm ission.
C omf ort -prov ides a comfort-oriented veh icle
setup and is suited for long drives on high­
ways .
Auto -provides an overall comfortable ye t dy­
nam ic dr iving feel and is suited for every day
u se.
Dynamic -gives the vehicle a sporty driving
feel and is suited to a spo rty dr iv ing style.
I n d iv idual * -c:> page 1 21 .
A WARNING
Pay attention to traffic when operating
drive select to prevent potential risk of an
accide nt.
-
You con personally specify the vehicle setup in the MMI ".
,.. Select: ICARlfunct ion button> Se t indiv id­
ual
control button . Once you select the
menu, you will automatically drive in the
i n ­
di vidual
mode .
System s Comfort
En gine /tran smi ssion
balanced
Steering comfortable
Dynamic ste ering * comfortable/ind ire ct
Adapt ive dampe rs* comfortable
A daptiv e cruise control * comfortable The equipment in your vehicle will determine
which sett
ings you can adjust. The following
table prov ides an overview of the characteris­
t ics of each driving mode.
Auto Dynamic
balanced sporty
balanced sporty
balanced/direct sporty/direct balanced sporty
balanced sporty

Automatic
transmission
tiptronic
Introduction
The automatic transmission is controlled elec­
tronically. The transmission upshifts or down­
shifts automatically depending on which drive
program is selected. The power is transferred
by a torque converter .
When a
mode rate d riv in g s ty le is used, the
transmission selects the most econom ica l
driving mode. It w ill then change up early and
delay the downshifts to g ive better fuel econ­
omy.
T he transmission switches to a sporty mode
after a k ick-down or when the driver uses a
spo rty driving sty le characterized by quick ac­
celerator pedal movements, heavy accelera­
tion, frequent changes in speed and traveling
at the maximum speed.
If desired, the driver can a lso select the gears
manually ( tiptronic mode ) c:> page 12 7.
Selector lever positions
Fig . 132 D isp lay in t he i nst ru m en t cluster: selecto r
l ever in pos it ion P
The selector lever position engaged appears
next to the selecto r lever as well as in the in­
strument clus ter disp lay.
P- P ark
In th is selector lever pos ition the transmis­
sion is mechan ically locked . Engage P only
when the vehicle is
completely stopped c:> 11::..
Automa tic tran sm iss ion 123
in Driving the automatic transmission on
page 126.
T o shift in or out of posit io n P , yo u m ust first
press and ho ld the brake pedal and then press
the re lease button in the selector leve r handle
whi le moving the selector lever to or from P.
You can shift out of th is position only with the
ignition on.
R -Reverse
Se lect R on ly when the vehicle is at a full stop
and the engine is running at idle speed c:> 11::.. in
Driving the automatic transmission on
page 126.
Before you move the se lector lever to R, press
both the button in the hand le o f the selector
lever
and the brake pedal at the same t ime.
When the ignition is on, the backup lights illu­
minate when the selecto r lever is moved into
R .
N -Neutral
The t ransm iss ion is in neut ral in this pos ition.
S hi ft to t his position fo r standing with the
brakes appl ied
c:> 11::.. in Driving the automatic
transmission on page 126 .
The vehicle can
also roll when the engine is stopped .
When the vehicle is stat iona ry or at speeds
below 1 mph (2 km/h), yo u m ust always apply
the footbrake before and whi le mov ing the
lever o ut of
N .
D/S - Normal position for driving forward
In the D/S pos ition, the transmission can be
operated either in the no rma l mode D or in
the sport mode S. To select the sport mode S,
pull the selector lever back briefly. Pulling the
lever back again will se lect the normal mode
D. The instrument cluster disp lay shows the
selected driving mode.
In the
normal mode D, the transmission auto­
matically selects the s uitable gear ratio. It de­
pends on engine load, vehicle speed and driv ­
ing style.
Se lect the
sport mode S for sporty dr iving .
The vehicle makes fu ll use of the engine's

124 Autom atic tr an smi ssion
power. Shifting may become noticeable when
accelerating . Hybrid drive*: electric driving is
not possible .
When the veh icle is stationary o r at speeds
below 1 mph (2 km/h), you must always apply
the foot brake before and while moving the
lever to D/S out of N.
A WARNING
Read and follow a ll WARNINGS c:> & in
Driving the automatic transmission on
page 126 .
@ Note
-
Coasting downhi ll with the transmission in
N and the engine not r unning w ill result in
damage to the automatic transmission
and possibly the catalytic converter .
(D Tips
-On vehicles with Aud i drive select*, you
can adjust the sporty sh ift characteristics
i n the
Dynamic driving mode.Swill ap­
pear in the instrument cluster display in­
stead of D .
- If you accidenta lly select N while driv ing,
take your foot off the acce lerator pedal
i mmediately and wait fo r the engine to
s low down to idle before se le cting D/S.
- Hybrid drive*: if the
lasvl button
c:> page 100 is pressed w hile in sport
mode S, the transm issio n sw itches auto­
matically to the normal mode D.
- If there is a power failure, the se lector
l ever will not move out of the P posi tio n.
The eme rgency release can be used if
this happens
q page 1 28.
Automatic Shift Lock {ASL)
The Automatic Shift Lock safeguards you
against accidentally shifting into a forward or
the reverse gear and causing the vehicle to
move unintentionally.
Fi g. 1 33 Shift gate: selecto r lever lock pos itions and
r elease button highl igh ted
The selector lever lock is released as follows :
.... Turn the ignition on.
.,.. Step on the brake pedal.
At the same time
press and hold the release button on the
side of the gear selector knob
c:> fig. 133
w ith your thumb until yo u have moved the
selecto r leve r to the desi red posit ion.
Automatic selector leve r lock
The selector lever is locked in the P and N po­
s itions when the ign ition is turned on . You
must p ress the brake pedal and t he release
button to select another position . As a re­
minde r to the drive r, the following wa rni ng
appea rs in the instrumen t clus ter display
when the sele ctor is in P and N:
When stationar y apply brak e pedal while se­
lec ting gear
The Automatic Shift Lock only funct ions when
t h e veh icle is stationary or at speeds be low
1 mph (2 km/h) .
At speeds above about 1 mph (2 km/h) the
Automat ic Shift Lock is automatically deact i­
vated in the N position .
A time delay element prevents the selector lever from locking when it is moved through
the N pos it ion (go ing from R to D/S) . The lock­
i ng element w ill lock the selecto r lever if t he
Ill>