2012 YAMAHA RHINO 700 brake

7-61
Downhill
Check the terrain carefully before going downhill.
When possible, choose a path that lets you drive
your vehicle straight downhill. Choose your path
carefully and drive slowly enough to be able to re-
act to obstacles that you encounter.
For more traction and control, before going down
steeper and/or rougher slopes, shift into low gear
and select “4WD” or “LOCK”. Engine braking will
help you go downhill slowly. Go as slowly as pos-
sible. If you begin to go too fast, apply the brakes
gently. Avoid hard application of the brakes, which
could cause the vehicle to slide.
1RB60-EE.book Page 61 Thursday, April 7, 2011 10:43 AM

7-67
Water
If you must cross shallow, slow-moving water up to
the depth of the vehicle’s floorboards, choose your
path carefully to avoid sharp drop-offs, large rocks,
or slippery surfaces that could cause the vehicle to
overturn. Never operate through water deeper
than 33 cm (13 in) or fast-flowing water. Choose a
path where both your entrance into and exit point
from the water is a gradual incline. Determine the
water depth and currents before crossing.
Operating this vehicle through deep or fast-flowing
water can lead to loss of control or overturn. To re-
duce your risk of drowning or other injuries, use
care when crossing through water.
Wet brakes may have reduced effectiveness. After
leaving the water, test your brakes. If necessary,
apply the brakes several times to let friction dry out
the linings.
1RB60-EE.book Page 67 Thursday, April 7, 2011 10:43 AM

7-75
Encountering obstacles
If you cannot go around an obstacle, such as a fall-
en tree or a ditch, stop the vehicle where it is safe
to do so. Set the parking brake and get out to in-
spect the area thoroughly. Look from both your ap-
proach side and exit side. If you believe you can
continue safely, choose the path that will allow you
to get over the obstacle and at as close to a right
angle as possible to minimize vehicle tipping. Go
only fast enough to maintain your momentum but
still give yourself plenty of time to react to changes
in conditions.
If there is any question about your ability to ma-
neuver safely over the obstacle, you should turn
around if the ground is flat and you have the room
or back up until you find a less difficult path.
1RB60-EE.book Page 75 Thursday, April 7, 2011 10:43 AM

8-3
WARNING
Turn off the engine when performing mainte-
nance unless otherwise specified.

A running engine has moving parts that
can catch on body parts or clothing and
electrical parts that can cause shocks or
fires.


Running the engine while servicing can
lead to eye injury, burns, fire, or carbon
monoxide poisoning – possibly leading to
death. See pages 2-17–2-19 for more infor-
mation about carbon monoxide.WARNING
Brake discs, calipers, drums, and linings can
become very hot during use. To avoid possible
burns, let brake components cool before
touching them.
1RB60-EE.book Page 3 Thursday, April 7, 2011 10:43 AM

8-8
EVU01650
General maintenance and lubrication chart
ITEM ROUTINEWhichever
comes firstINITIAL EVERY
month136612
km
(mi)320
(200)1200
(750)2400
(1500)2400
(1500)4800
(3000)
hours 20 75 150 150 300
Cooling system*Check coolant leakage.
Repair if necessary.
Replace coolant every 24 months.
Air filter elementClean.
Replace if necessary.Every 20–40 hours
(More often in wet or dusty areas.)
Engine oilReplace (warm engine before draining).Engine oil filter cartridgeReplace.Final gear oil
Check oil level/oil leakage.
Replace.Differential gear oil
Front brake*Check operation/brake pad wear/fluid leakage/see page 8-9.
Correct if necessary. Replace pads if worn to the limit.Rear brake*Check operation/brake pad wear/fluid leakage/see page 8-9.
Correct if necessary. Replace pads if worn to the limit.Parking brake*Check operation and free play/brake pad wear.
Correct if necessary. Replace pads if worn to the limit.Accelerator pedal*Check operation and free play.V-belt*Check operation.
Check for wear, cracks, or damage.Wheels*Check balance/damage/runout.
Repair if necessary.Wheel bearings*Check bearing assemblies for looseness/damage.
Replace if damaged.Front and rear
suspension*Check operation and for leakage.
Correct if necessary.Steering system*Check operation and for looseness/Replace if damaged.
Check toe-in/Adjust if necessary.Rear upper and lower
knuckle pivots*Lubricate with lithium-soap-based grease.
1RB60-EE.book Page 8 Thursday, April 7, 2011 10:43 AM

8-9
TIP

Some maintenance items need more frequent service if you are riding in unusually wet, dusty, sandy or
muddy areas, or at full throttle.


Hydraulic brake service
Regularly check and, if necessary, correct the brake fluid level.
Every two years replace the internal components of the brake master cylinder and calipers, and
change the brake fluid.
Replace the brake hoses every four years and if cracked or damaged.
Drive shaft universal joint*Lubricate with lithium-soap-based grease.Engine mount*Check for cracks or damage.
Check bolt tightness.Front and rear axle boots*Check operation.
Replace if damaged.Stabilizer bushings*Check for cracks or damage.Fittings and fasteners*Check all chassis fittings and fasteners.
Correct if necessary.
ITEM ROUTINEWhichever
comes firstINITIAL EVERY
month136612
km
(mi)320
(200)1200
(750)2400
(1500)2400
(1500)4800
(3000)
hours 20 75 150 150 300
1RB60-EE.book Page 9 Thursday, April 7, 2011 10:43 AM

8-21 1. Console
1. Console
1. Consola
1
5B410011
Console
To remove
1. Remove the seats. (See page 4-37 for seat
removal and installation procedures.)
2. Remove the parking brake lever boot.
3. Pull the console forward and upward (the
drive select lever boot will come loose). To
ease removal of the console, shift the drive
select lever into the low gear “L” position.
1RB60-EE.book Page 21 Thursday, April 7, 2011 10:43 AM

8-23
To install
1. Place the console in its original position.
2. Install the parking brake lever boot.
3. Install the seats.NOTICE

Be sure to position the seat belt buckles to
the outside of the console.


When installing the console, be sure not to
pinch the cables or wires.


Make sure that the groove at the bottom of
the parking brake lever boot and the drive
select lever boot fits securely around the
edge of the hole in the console.
1RB60-EE.book Page 23 Thursday, April 7, 2011 10:43 AM