2012 YAMAHA RHINO 700 brake

8-105 1. Brake light switch 2. Adjusting nut
1. Contacteur de feu stop 2.Écrou de réglage
1. Interruptor de la luz de freno 2. Tuerca de ajuste
1a
b
2
EVU00880
Brake light switch adjustment
The brake light switch, which is activated by the
brake pedal, is properly adjusted when the brake
light comes on just before braking takes effect. If
necessary, adjust the brake light switch as follows.
1. Open the hood. (See pages 8-17–8-19 for
hood opening and closing procedures.)
2. Turn the adjusting nut while holding the brake
light switch in place. To make the brake light
come on earlier, turn the adjusting nut in
directiona. To make the brake light come on
later, turn the adjusting nut in directionb.
3. Close the hood.
1RB60-EE.book Page 105 Thursday, April 7, 2011 10:43 AM

8-109
EVU00900
Brake pedal and accelerator pedal lubrication
Lubricate the pivoting parts.
Recommended lubricant:
Lithium-soap-based grease
1RB60-EE.book Page 109 Thursday, April 7, 2011 10:43 AM

8-151 1. Panel A
1. Cache A
1. Panel A
1
1. Panel B
1. Cache B
1. Panel B
1
EVU01000
Tail/brake light bulb replacement
If a tail/brake light bulb burns out, replace it as fol-
lows:
1. Remove the quick fastener screws, nuts and
bolts from panel A (if replacing the left tail/
brake light bulb) or panel B (if replacing the
right tail/brake light bulb).
1RB60-EE.book Page 151 Thursday, April 7, 2011 10:43 AM

8-153 1. Quick fastener screw (× 8)
2. Bolt and nut (× 2) 3. Panel A
1. Vis à serrage rapide (× 8)
2. Vis et écrou (× 2) 3. Cache A
1. Tornillo de fijación rápida (× 8)
2. Perno y tuerca (× 2) 3. Panel A
1
3
1 2 1
1. Tail/brake light bulb holder
1. Porte-ampoule de feu arrière/stop
1. Bombilla de la luz de freno/piloto trasero
2. Lift the cargo bed up. (See page 4-47 for car-
go bed lifting and lowering procedures.)
3. Remove the panel (panel A or B).
4. Remove the tail/brake light bulb holder (to-
gether with the bulb) by turning it counter-
clockwise.
5. Push the burnt-out bulb in and turn it counter-
clockwise to remove it from the bulb holder.
6. Push a new bulb in and turn it clockwise to in-
stall in the bulb holder.
1RB60-EE.book Page 153 Thursday, April 7, 2011 10:43 AM

9-3
3. Rinse the dirt and degreaser off with a garden
hose. Use only enough pressure to do the
job. WARNING! Test the brakes after
washing. Apply the brakes several times
at slow speeds to let friction dry out the
linings. Wet brakes may have reduced
stopping ability, increasing the chance of
an accident. NOTICE: Excessive water
pressure may cause water seepage and
deterioration of wheel bearings, brakes,
transmission seals and electrical devices.
Many expensive repair bills have resulted
from improper high-pressure detergent
applications, such as those available in
coin-operated car washers.
1RB60-EE.book Page 3 Thursday, April 7, 2011 10:43 AM

10-4
Rear wheel:Wheel type:
YXR700FAB Panel wheel
YXR7FSPB Cast wheel
YXR7FB Panel wheel
Rim size:
12 × 7.5ATFront brake:Type:
Disc brake
Operation:
Unified brake
Specified brake fluid:
DOT 4Rear brake:Type:
Disc brake
Operation:
Unified brake
Specified brake fluid:
DOT 4Front suspension:Type:
Double wishbone
Spring/shock absorber type:
YXR700FAB Coil spring/oil damper
YXR7FSPB Coil spring/gas-oil damper
YXR7FB Coil spring/oil damper
Wheel travel:
185 mm (7.3 in)
Rear suspension:Type:
Double wishbone
Spring/shock absorber type:
YXR700FAB Coil spring/oil damper
YXR7FSPB Coil spring/gas-oil damper
YXR7FB Coil spring/oil damper
Wheel travel:
185 mm (7.3 in)Electrical system:Ignition system:
TCI
Charging system:
AC magnetoBattery:Model:
U1L-11
Voltage, capacity:
12 V, 28.0 AhHeadlight:Bulb type:
Krypton bulbBulb voltage, wattage × quantity:Headlight:
12 V, 30.0/30.0 W × 2
Tail/brake light:
12 V, 5.0/21.0 W × 2
Neutral indicator light:
LED
Reverse indicator light:
LED
1RB60-EE.book Page 4 Thursday, April 7, 2011 10:43 AM

10-5 Coolant temperature warning light:
LED
Engine trouble warning light:
LED
Parking brake indicator light:
LED
On-Command four-wheel-drive/differential gear lock indica-
tor:
LCD
High-range indicator light:
LED
Low-range indicator light:
LED
Differential gear lock indicator light:
LED
Helmet/seat belt indicator light:
12 V, 0.7 W × 2
Fuses:Main fuse:
40.0 A
Fuel injection system fuse:
10.0 A
Headlight fuse:
15.0 A
Signaling system fuse:
10.0 A
Ignition fuse:
10.0 A
Auxiliary DC jack fuse:
10.0 A
Backup fuse:
10.0 AFour-wheel-drive motor fuse:
10.0 A
Radiator fan fuse:
25.0 A
For EUR only
The figures quoted are emission levels and are not
necessarily safe working levels. Whilst there is a
correlation between the emission and exposure
levels, this cannot be used reliably to determine
whether or not further precautions are required.
Factors that influence the actual level of exposure
of work-force include the characteristics of the
work room, the other sources of noise, etc. i.e. the
number of machines and other adjacent process-
es, and the length of time for which an operator is
exposed to the noise. Also the permissible expo-
sure level can vary from country. This information,
however, will enable the user of the machine to
make a better evaluation of the hazard and risk.
1RB60-EE.book Page 5 Thursday, April 7, 2011 10:43 AM