2012 SSANGYONG NEW ACTYON SPORTS transmission

(2) CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION (1) CONNECTOR INFORMATION TRANSMISSION, DIAGNOSIS, CAN LINE 2)

02-110000-00
3160-01 Manual transmission
Added 5 and 6-speed transmission
3680-01 Automatic transmission
Changed the torque conver & torque converter housing due to new engine
OldNew
OldNew
2412-02 CDPF
Introduced CDPF to meet EURO-5
regulation
2411-01 DOC
Introduced DOC to meet EURO III or
EURO IV regulation.
G23D
D20DTR

01-110000-00
6. CODING AND INITIALIZATION
1) Engine Variant Coding
Unit Selection Description Remarks
PTC auxilary heater NO For PTC auxilary heater
equipped vehicle, select
"YES".-
YES YES
Glow plug Relay (K-line) Select "AQGS". -
AQGS (CAN) AQGS (CAN)
Transmission 6-speed M/T "DSI 6 AT" is selected
automatically.Select
5-speed A/T (DC 5 AT) -
6-speed A/T (DSI 6 AT) Select
Pressure sensor for
A/C refrigerantNO Select the appropriate
system.-
Type Pressure
sensor for A/C
refrigerant
Immobilizer NO Select "YES" if the vehicle
has immobilizer.-
YES YES
Vehicle speed input
typeCAN Select "CAN" if the vehicle
has ABS or ESPCAN
WIRE -
Fan 2 relays Select "PWM". -
PWM fan PWM fan
Auto cruise NO Select "YES" if the vehicle
has cruise contro.-
YES YES
G-sensor NO 2WD ABS & Non-ABS: NO
4WD ABS & ESP: YESSelect
YES Select

01-170000-00
Name: Oil pan gasket
remover
Use to separate oil pan and
minimize damage when
removing oil pan.
Name: Torque angle gauge
Use to angle-tighten correctly
after torque-tightening
Name & Part number Tool How to use
Name: Engine stand (1 tone
or more)
Use to fix the removed engine
or engine with transmission.
Name: Engine crane (1 tone
or more)
Use to move the engine
module (including
transmission) to working
space or engine stand.
2. NORMAL EQUIPMENTS

02-190000-00
Front mounting insulator (Left side)
Location InsulatorFront mounting insulator (Right side)
Location Insulator
3. ENGINE MOUNTING
D20DTR engine uses 3-point mounting type that supports the engine and transmission
simultaneously.
Components ▶
Rear mounting insulator
2WD 4WD
A/T M/T A/T M/T

15-370000-00
HFM (intake air
temperature)Cooling fan module
DSI 6 A/T (ATF
temperature)Coolant
temperature senso
r
Refrigerant
pressure sensor
Relay box
(12) Cooling fan control
A. Overview of cooling fan and A/C compressor
The cooling system maintains the engine temperature at an efficient level during all engine
operating conditions. The water pump draws the coolant from the radiator. The coolant then
circulates through water jackets in the engine block, the intake manifold, and the cylinder head.
When the coolant reaches the operating temperature of the thermostat, the thermostat opens.
The coolant then goes back to the radiator where it cools. The heat from automatic transmission
is also cooled down through the radiator by circulating the oil through the oil pump. ECU controls
the electric cooling fans with three cooling fan relays to improve the engine torque and air
conditioning performance.
For detailed information, refer to Chapter "Air Conditioning System".
B. Components
A/C compressor
D20DTR ECU

01-91113-01
4. DIAGNOSTIC INFORMATION AND PROCEDURE
1) Oil Leak Diagnosis
Most fluid oil leaks are easily located and repaired by visually finding the leak and replacing or
repairing the necessary parts. On some occasions a fluid leak may be difficult to locate or repair.
The following procedures may help you in locating and repairing most leaks.
Finding the Leak ▶
Identify the fluid. Determine whether it is engine oil, automatic transmission fluid, power
steering fluid, etc.
Identify where the fluid is leaking from. -
-
After running the vehicle at normal operating temperature, park the vehicle over a large
sheet of paper.
Wait a few minutes.
You should be able to find the approximate location of the leak by the drippings on the
paper. ·
·
·
Visually check around the suspected component.
Check around all the gasket mating surfaces for leaks. A mirror is useful for finding leaks
in areas that are hard to reach.
If the leak still cannot be found, it may be necessary to clean the suspected area with a
degreaser, steam or spray solvent. -
-
Clean the area well.
Dry the area.
Operate the vehicle for several miles at normal operating temperature and varying
speeds.
After operating the vehicle, visually check the suspected component.
If you still cannot locate the leak, try using the powder or black light and dye method. ·
·
·
·
·
Clean the suspected area.
Apply an aerosol-type powder (such as foot powder) to the suspected area.
Operate the vehicle under normal operating conditoins.
Visually inspect the suspected component. You should be able to trace the leak path over
the white powder surface to the source. -
-
-
- Powder Method ▶

05-8
5) Jump Starting Procedure
Position the vehicle with the charged battery so that the jumper cables will reach from the
charged battery to the battery that requires charging.
Turn off the ignition, all the lights, and all the electrical loads in both vehicles.
Leave the hazard flasher on if jump starting where there may be other traffic and any other
lights needed for the work area.
Apply the parking brake firmly in both vehicles. 1.
2.
3.
4.
Shift an automatic transmission to PARK. 5.
Clamp one end of the first jumper cable to the positive terminal on the booster battery. Make
sure it does not touch any other metal parts.
Clamp the other end of the same cable to the positive terminal on the discharged battery.
Never connect the other end to the negative terminal of the discharged battery. 6.
7.
Clamp one end of the second cable to the negative terminal of the booster battery.
Make the final connection to a solid engine ground, such as the engine lift bracket at least 450
millimeters (18 inches) from the discharged battery.
Start the engine of the vehicle with the good battery.
Run the engine at a moderate speed for several minutes.
Then start the engine of the vehicle with the discharged battery.
Remove the jumper cables by reversing the above sequence exactly, removing the negative
cable from the vehicle with the discharged battery first.
While removing each clamp, take care that it does not touch any other metal while the other
end remains attached. 8.
9.
10.
11.
12.In order to avoid damaging the vehicle make sure the cables are not on or near pulleys, fans,
or other parts that will move when the engine starts.
In order to avoid injury, do not use cables that have loose or missing insulation.