2012 SSANGYONG KORANDO lock

06-40
Door coupled room lamp operation and dimming control ▶
When opening any of doors while the room lamp switch in overhead console is pressed in ("Door"
coupled position), the front and center room lamps come on. If the key is removed and door stays open,
the room lamps automatically goes off after 10 minutes. The sleep mode will be deactivated when the
door is locked or closed with the lamp OFF automatically.
When closing the door with IGN ON, the room lamps go off immediately.
When closing the door with IGN OFF, the room lamps stay on for 2 seconds more and are dimmed
out the side fascia panel.
When turning the ignition switch to ON position during dimming out operation, the room lamps go off
immediately.
When receiving the door unlock signal with IGN OFF, key removed and door closed, the overhead
console room lamp/center room lamp come on for 30 seconds.
For specification with the SKM, the lamps come on by the REKES unlock or passive unlock signal.
When receiving the door unlock signal again while the lamps stay on by the REKES or passive unloc
k
signal, the overhead console/center room lamps stays on for 30 seconds more. (the lamps stay on
when receiving door unlock signal)
When opening a door during the coupled operation and dimming operation, the room lamps stays
ON. When closing it again, the lamps stay on for 2 seconds more and are dimmed out for 3 seconds.
While the room lamps dim out when the driver/passenger/rear doors are open and closed, they go off
immediately when entering into the theft deterrent mode.
The room lamps come on when AUTO approach signal is received. 1.
2.
3.
4.
5.
6.
7.
8.

06-438510-00
Tailgate open ▶
When pressing the tailgate switch for more than 0.1 second with driver door unlocked and vehicle
<009a0097008c008c008b00470089008c00930096009e0047005a0047004f00b700570055005800500047009200940056008f00530047009b008f008c0047009b008800900093008e0088009b008c004700960097008c009500470099008c0093008800a000
470090009a0047009b009c00990095008c008b004700760075> for about 1 second, with
power OFF, ACC ON or IGN ON. However, it is turned ON when the vehicle speed is below 3
(±0.1) km/h, with IGN ON.
The tailgate open relay is turned OFF immediately after the driver door is locked or the vehicle speed
goes over 3 km/h with IGN ON during its operation. However, the BCM does not operate if the tailgate
open switch is pressed when the vehicle speed is above 3 km/h. 1.
2.
<007b008800900093008e0088009b008c004700960097008c0095006100470079006c0072006c007a0047009c009500930096008a00920047004f008b0090009a008800990094008c008b0047008b008c009b008c00990099008c0095009b00470094009600
8b008c0050004702e70047007b008800900093008e0088009b>e open signal → Tailgate
open - Without SKM
When pressing the tailgate switch for more than 0.1 second with driver door unlocked and vehicle
<009a0097008c008c008b00470089008c00930096009e0047005a0047004f00b700570055005800500047009200940056008f00530047009b008f008c0047009b008800900093008e0088009b008c004700960097008c009500470099008c0093008800a000
470090009a0047009b009c00990095008c008b004700760075> for about 1 second.
The tailgate open relay is turned OFF immediately after the driver door is locked or the vehicle speed
goes over 3 km/h during its operation.
When the tailgate switch on smart key is pressed in theft deterrent mode or with the smart key
detected by the exterior antenna, the SKM verifies the smart key and disarms the tailgate only. When
the tailgate is open and closed, the system enters into the theft deterrent mode again. If the tailgate
switch is not operated for 30 seconds, the system also does so.
The BCM checks that the verified smart key is in the luggage room 1 second after when the closed
tailgate is detected by the tailgate open switch with power OFF.
If there is a verified smart key in the luggage room when the tailgate is open and closed in theft
deterrent mode, the external buzzer sounds for 5 seconds.
When the driver press the tailgate open switch in order to look for the smart key, the BCM deactivates
lock so that the tailgate can be opened even though the driver door is locked. (maintains standby for
opening without verification) 1.
2.
3.
4. With SKM

07-118310-00
Approach (puddle) lamp
(7) Puddle (approach) lamp
Approach lamp ON 1.Lamp control for models with SKM ▶
When turning the ignition switch to OFF from ON position and opening the driver door, the
approach lamps come ON.
When receiving the UNLOCK signal from the smart key remote control or outside door handle
switch signal in the theft deterrent mode, the approach lamps come ON for 30 seconds.
When receiving the AUTO approach signal in the theft deterrent mode, the approach lamps come
ON for 30 seconds. -
-
-
Approach lamp OFF 2.
When receiving the door lock signal from the smart key remote control or outside door handle
switch signal with the approach lamps ON, the lamps go OFF (reactivation of theft deterrent
mode).
When turning the ignition switch to ON position with the approach lamps ON, the lamps go OFF.
The approach lamps go OFF after 30 seconds. -
-
- Approach lamp ON 1.Lamp control for models without SKM ▶
When receiving the UNLOCK signal in the theft deterrent mode, the approach lamps come ON for
30 seconds.
When turning the ignition switch to OFF from ON position and opening the driver door, the
approach lamps come ON. -
-
Approach lamp OFF 2.
When receiving the door lock signal with the approach lamps ON, the lamps go OFF (reactivation
of theft deterrent mode).
When turning the ignition switch to ON position with the approach lamps ON, the lamps go OFF.
The approach lamps go OFF after 30 seconds. -
-
-

07-14
2) Operation
(1) Front room lamp/Center room lamp
Front room lamp Center room lamp
Operating the front room lamp and center room lamp switches illuminates the driver/passenger side
lamps and center room lamp.
Room lamp control by door coupled room lamp operation ▶
If a door except the tailgate is opened after the ignition is turned off, provided that door coupled front
room lamp switch is pressed, the front room lamp and center room lamp are illuminated for 2 sec.
and then fade out for 3 sec.
If a door except the tailgate is opened and then closed while the room lamp is fading out, the room
lamp is illuminated for 2 sec. and then fades out for 3 sec. If the ignition is turned on, the room lamp
goes off immediately.
The front room lamp and center room lamp are illuminated for 30 sec. when the door is unlocked by
the REKES or passive door UNLOCK function with IGN OFF and the ignition key removed. If the
REKES or passive door UNLOCK signal is received again, the room lamps are illuminated for
another 30 sec.
The room lamp goes off immediately when the REKES or passive door LOCK signal is received or
the ignition switch is turned to ON position.
If the room lamp is turned on after the ignition key is removed (door open or room lamp switch is
pressed), it is turned off after 10 minutes by the BCM.
When the door open state is changed or the ignition is turned on after the room lamp has been turned
off automatically, the battery saver feature is reset. 1.
2.
3.
4.
5.

09-8
3. OPERATING PROCESS
1) Block Diagram
When PAS receives "R" signal, it starts to detect the obstacles behind vehicle after self diagnosis.
If the system detects the obstacle, the buzzer sounds according to the distance. If there is no obstacle, starts
to detect the obstacles after self diagnosis again.

01-10
A/T assembly
Automatic transmission is available as 4WD- and 2WD-type,
and provides 6 speeds for forward travel and 1 reverse
travel. It is also equipped with the torque converter with inner
lock-up clutch and electronically controlled solenoid which
controls all hydraulic functions.
3. CHASSIS COMPONENT LAYOUT
PTU (Power Transfer Unit)
The PTU is a device that transfers the power
generated from the engine to the rear axle through
propeller shaft and E-coupling by changing the power
<008d00930096009e0047008b00900099008c008a009b0090009600950047008900a000470060005700b60047009000950047009b008f008c0047008d009900960095009b0047009e008f008c008c00930047008b00990090009d008c0047009b00a0009700
8c0047>
4WD vehicle.
Rear axle assembly
The rear axle installed in this car is a removable
axle, called IRDA (Independent Rear Differential
Axle). The rear differential carrier is installed
directly on the sub frame, and there is an
independent suspension that allows each wheel
on the same axle to move vertically independentl
y
of each other with the universal joint and the slip
joint.
E-coupling control unit (E-Coupling ECU)
The E-coupling unit is a control unit which determines
the magnetic force by considering CAN signals (wheel
speed, engine torque, pedal opening, ABS/ESP CAN
signals, etc.) from other ECUs.
Inhibitor switch
Torque converter Oil pan
E-coupling sideRear axle side
Propeller shaft
1) 4WD Vehicle With Automatic Transmission
GSLDSLInhibitor switch
Torque converter Oil pan

01-230000-00
3) General Instructions
Before lifting up the vehicle with a lift, correctly support the lifting points.
When using a jack, park the vehicle on a level ground and place the wheel chocks under the tires.
Position the jack under the frame and lift up the vehicle and then support with chassis stand before
service work.
Make sure to disconnect the negative (-) cable from the battery to prevent any damage to electric
systems.
If you have to work on vehicle, cover the seats and floor with protection covers to avoid any
damage and contamination.
Brake fluid and anti-freeze can damage the painted surface of body. So carefully handle them
during service work.
To improve the efficiency of service work, use only recommended and specified tools.
Use only Ssangyong genuine spare parts.
Never reuse the cotter pin, gasket, O-ring, oil seal, lock washer and self-locking nut. Replace them
with new ones. If reused, normal functions cannot be maintained.
Store the disassembled parts as a set based on disassembly order and unit.
Pay particular attention not to miss or mix the fasteners.
If necessary, especially for inspection, clean the removed parts completely.
Apply the oil or grease on the running and sliding surfeces before installation. Use the specified
sealant and gasket to prevent leakage if necessary.
Tighten the fasteners to the specified tightening torque.
As a final stage of service work, check if the serviced system is working properly and the problem
has been eliminated clearly. (1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14) Remove the engine and transaxle as a set.
Manual transaxle: Transaxle can be separated after removing the front module (sub frame, engine
and transaxle).
Automatic transaxle: Transaxle can be separated after removing the sub frame. -
-
2) Equipment
Korando is FF (Front Engine Front Drive) type vehicle, and engine and powertrain system are
integrated into a module. Therefore, 2-post lift and general equipment are necessary when working
on the engine and transmission.
Major equipment: Engine and transmission jack, Engine stand, Engine crane, Transmission jack,
Engine hanger -
-
Engine stand
Engine crane

02-33680-01
1. GENERAL INFORMATION
Automatic transaxle (M11) ▶
The Model 11 six speed automatic transaxle is
available in two variants: four wheel drive and two
wheel drive.
Six forward speeds
One reverse gear
A toruqe converter with an integral converter
lock-up clutch with slip control capabilities
Electronic shift and pressure controls
A single planetary gear-set
A double planetary gear-set
One hydraulically controlled brake bands
Three multi-plate clutches
One multi plate brake
All hydraulic functions are directed by electronic
solenoids to control: -
-
-
-
-
-
-
-
-
-
Engagement feel
Shift feel
Shift scheduling
Modulated torque converter clutch
applications 1)
2)
3)
4) Inhibitor switch
Oil pan
Torque converter
TCU (located under driver's seat) ▶
TCU is located under the driver's seat and controls
the transaxle operations.
TCU is activated and deactivated by the ignition
voltage, and connected to the transaxle through
pin 26 in connector.
TCU receives and uses the signals from sensors
and switches through CAN bus with analog and
digital types. Driver seat
E-coupling unit
TCU
Passenger
seat