2012 SSANGYONG KORANDO lock

04-98712-03
Passive function actuation area: Within 1 m from the door handle
Passive tailgate open actuation area: Within 1 m from the bumper -
-Response signal
(RF transmission) Verification request signal
(LF transmission)Smart key
Passive function
operating range
Passive
trunk open
operating range
Passive function
operating range
2) Smart Key Function
(1) Passive entry actuation area
Passive entry actuation area ▶Searching for a smart key signal from the outside the vehicle is prioritized in theft deterrent mode.
Searching for a smart key signal from the inside is prioritized when the theft deterrent mode is
deactivated.
The smart key verification is performed only for the driver's or passenger's door which has received
the input from the corresponding door handle switch. If a verified smart key is found, the passive entry
function is performed.
A maximum of 3 keys can be registered. -
-
- The passive LOCK/UNLOCK is performed by the input from the outside door handle switch.
(For driver's door LOCK/UNLOCK)

04-118712-03
(2) Passive LOCK
When the system searches for a smart key by the input from the outside door handle switch, the SKM
sends the passive LOCK signal to the BCM if all the doors are closed and a normal smart key is found
outside the vehicle.
Passive LOCK hardware control ▶
The SKM sends the door LOCK/UNLOCK signal to the BCM through the BCAN network when a
smart key is verified after the signal from the driver/passenger outside door handle switch is received
through the hardware.
The SKM sends the signal to the BCM and instrument cluster when the warning and indicator
display conditions are met. 1.
2.
Passive LOCK by outside door handle switch ▶
When the ignition status is OFF, ACC ON or IGN ON, the SKM performs the verification procedure if the
LOCK signal is received from the driver/passenger door handle switch.
When the outside door handle switch is operated, the SKM verifies if a smart key is outside the
vehicle using the corresponding exterior antenna.
The SKM sends the signal for [Passive LOCK command] to the BCM through the BCAN if a smart
key is identified as being outside the vehicle.
If no smart key is verified as being outside the vehicle, this process is stopped and restarted when the
next signal is received from the outside door handle switch.
When the driver's door is unlocked with the ignition status ACC ON, the SKM changes the ignition
status to OFF and sends the signal for [Passive LOCK command] to the BCM through the BCAN to
lock the door. The BCM ignores the signal if the ignition status is IGN ON.
The SKM recovers the deactivated smart key function inside the vehicle when it receives the theft
deterrent deactivation signal from the BCM through the BCAN communication. 1.
2.
3.
4.
-

04-12
The system first identifies the last smart key used, and then identifies all the other registered smart
keys until a normal smart key is verified.
The system identifies the smart keys by using the outside door handle antenna on the door handle
switch which has sent the signal.
Smart key search input: The last door is opened and then closed. Outside door handle switch, Brake
switch, START switch (Tailgate open request) 1.
2.
3.Smart key search mode ▶Searching for other keys ▶
When the ignition status is IGN ON or ACC ON, the SKM starts to verify the smart key if any door is
opened and then closed. If one or more smart keys are verified as being in the vehicle, the smart key
verification procedure is stopped. If no verified smart key is identified as being in the vehicle, the SKM
sends the signal which identifies that there is no verified key inside the vehicle to the BCM and instrument
cluster through the BCAN (Smart key not identified warning).Interruption of door LOCK & Smart key function by outside door handle switch ▶
When the door LOCK signal is received from the driver/passenger door handle switch with the ignition
status OFF or ACC ON, the SKM identifies the verified smart key and sends the passive LOCK signal
to the BCM through the BCAN if the ignition is turned to OFF.
The SKM receives the theft deterrent mode information signal from the BCM through the BCAN.
If there is any verified smart key in the vehicle, the function of the verified smart key is interrupted. 1.
2.
3.

04-138712-03
(3) Passive UNLOCK
When the system searches for a smart key by the input from the outside door handle switch, the SKM
sends the passive UNLOCK signal to the BCM if all the doors are closed and a normal smart key is
found outside the vehicle.
Passive UNLOCK hardware control ▶
The SKM sends the door LOCK/UNLOCK signal to the BCM through the BCAN network when a
smart key is verified after the signal from the driver/passenger outside door handle switch is received
through the hardware. 1.
Passive UNLOCK by outside door handle switch ▶
When the ignition status is OFF, ACC ON or IGN ON, the SKM starts to verify the smart key if below
conditions are met.
When the driver or passenger door handle switch is operated, the SKM verifies if a smart key is outside
the vehicle using the corresponding antenna.
When the outside door handle switch is operated, the SKM verifies if a smart key is outside the
vehicle using the corresponding exterior antenna.
The SKM sends the signal for [Passive UNLOCK command] to the BCM through the BCAN if a
smart key is identified as being outside the vehicle.
If no smart key is identified as being outside the vehicle, this process is stopped and restarted when
the next signal is received from the outside door handle switch.
When the driver's door is locked with the ignition status ACC ON or IGN ON, the SKM sends the
signal for [Passive UNLOCK command] to the BCM through the BCAN to unlock the door without
changing the ignition status to OFF. 1.
2.
3.
4.
Smart key search mode ▶
The system first identifies the last smart key used, and then identifies all the other registered smart
keys until a normal smart key is verified.
The system identifies the smart keys by using the outside door handle antenna on the door handle
switch which has sent the signal.
Smart key search input: The last door is opened and then closed. Outside door handle switch, Brake
switch, START switch (Tailgate open request)
Exceptional mode
When operating the door handle switch, the system changes the smart key searching conditions in
vehicle inside and outside according to the theft deterrent mode.
- Searching sequence when disarmed by BCM: Inside > Outside
- which function is restricted when the BCM is in theft deterrent mode. 1.
2.
3.
4.

04-158712-03
(5) Puddle (approach) lamp control
Operating condition ▶
When the driver approaches the vehicle in theft deterrent mode (within 1 m), the SKM sends the
puddle lamp operation signal through the BCAN if a smart key is identified.
The SKM starts to search for a smart key 30 sec. after the vehicle has entered the theft deterrent
mode. -
-
Continuous operation ▶
Reset conditions ▶
Standby mode operation ▶When a smart key is identified within 1 m from the vehicle in theft deterrent mode, the SKM sends the
puddle lamp operation signal (10 min. timer activated) through the BCAN. If a smart key is
continuously found within 10 min. the SKM sends the puddle lamp signal again for continuous
operation (up to 2 times within 10 min.)
The SKM starts to search for a smart key 30 sec. after sending the 1st puddle lamp operation signal.
If a smart key is found, the SKM sends the 2nd operation signal. -
-
10 min. timer terminated
Re-entering theft deterrent mode after deactivation -
-
Duration Function Time (s)
1st within 5 days Normal monitoring time 1.25
2nd within 5 to 14 days Increasing monitoring time 1.5
3rd 14 days or more Vehicle is stationary.
The SKM sends the signals for [AUTO approach], [REKES UNLOCK] and [Passive UNLOCK] through
the BCAN to control the puddle (approach) lamp by AUTO puddle (approach) lamp ON, REKES
UNLOCK and Passive entry UNLOCK.
Default setting is AUTO approach.
The AUTO approach function can be turned ON or OFF using a diagnostic device.AUTO puddle (approach) lamp ON ▶
REKES or Passive door LOCK/UNLOCKStop/Standby operation reset condition: ▶
The SKM sends the signals for [REKES UNLOCK] and [Passive UNLOCK] to control the puddle
(approach) lamp ON function by REKES UNLOCK and Passive entry UNLOCK in theft deterrent mode. Puddle (approach) lamp ON by REKES UNLOCK & Puddle (approach) lamp ON by Passive
entry UNLOCK ▶

04-16
(6) Limitations/Interruption of smart key function
The SKM searches for a smart key inside the vehicle when it receives the information on entering the
theft deterrent mode from the BCM. If a normal smart key is identified, the SKM memorizes this as a
function-limited key (Silent Smart Key) or a function interrupted key (Deactivation Smart Key) according
to the conditions.
If a smart key, which outputs the door LOCK signal, is found inside the vehicle, the SKM memorizes
all the smart keys inside the vehicle as function limited keys (Silent Smart Key).
The function limited smart key provides the passive START, ignition status change and REKES
functions except the passive UNLOCK function. -
-Function limitation ▶
Function interruption ▶
How to deactivate function limited/interrupted smart key ▶
Deactivate the theft deterrent mode. -If no smart key, which outputs the door LOCK signal, is found inside the vehicle, the SKM memorizes
all the smart keys inside the vehicle as function interrupted keys (Deactivation Smart Key).
The function interrupted smart key is not available for the passive LOCK/UNLOCK, passive START,
ignition status change and REKES functions. -
-

04-178712-03
3) REKES Control Function
(2) REKES UNLOCK
The SKM receives the signal for [REKES UNLOCK] 0.1 sec. after the UNLOCK button on the smart
key is turned ON, and sends this signal through the BCAN. - When the SKM receives the REKES signals by the buttons on the smart key, it transmits the
corresponding signals through the BCAN.
Switch Stage Remark
LOCK 1 step
100 ms: 1 step CMD
1500 ms: 2 step CMD
1000 ms: 3 step CMD unlocked 1 step
Tailgate open 3 step
PANIC 3 step
(3) Remote keyless tailgate open
When the SKM receives the signal for [REKES UNLOCK] by the UNLOCK button on the smart key, it
transmits this signal through the BCAN.
(1) REKES LOCK
The SKM receives the signal for [REKES LOCK] 0.1 sec. after the LOCK button on the smart key is
turned ON, and it transmits this signal through the BCAN.
When the REKES LOCK signal is received with the ACC ON, the ACC is turned OFF and the signal
for [REKES LOCK] is sent. -
- When the SKM receives the signal for [REKES LOCK] by the LOCK button on the smart key, it transmits
this signal through the BCAN.
The SKM receives the tailgate open signal 1 sec. after the tailgate open button on the smart key is
turned ON with the ignition status OFF, ACC or IGN ON, and it transmits the signal for [REKES
tailgate open] through the BCAN. - When the SKM receives the signal for [REKES tailgate open] by the tailgate open button on the smart
key, it transmits this signal through the BCAN.
Remote keyless tailgate open ▶

04-238712-03
(4) Engine stop
When the START button is pressed at the vehicle speed of 3 km/h or less, the SKM turns off the IGN
relay to stop the engine.
When the vehicle speed is 3 km/h or more or no speed signal is input, the SKM performs the
following functions: 1.
2.
When the START switch is pressed for 3 sec. or more at more than 3 km/h, the ignition status is
changed from IGN to ACC.
If the switch is pressed again, the ignition status is changed from ACC to IGN.
When the START switch is pressed for 3 sec. or more with no vehicle speed signal (CAN signal
timeout, abnormal signal), the ignition status is changed from IGN to ACC. If the switch is pressed
again, the ignition status is changed from ACC to OFF. -
-
When the START button is pressed and held with IGN ON, the ignition status is changed to OFF.
When the START button is pressed briefly, the ignition status is changed to ACC ON. 3.
(5) ACC ON/Power OFF
The SKM changes the ignition status to OFF from ACC ON when:
the engine START/STOP button is pressed with the brake pedal released after the ignition status is
changed from IGN ON to ACC ON.
the REKES LOCK or passive LOCK is operated with ACC ON.
the BCM sends the driver's door open signal.
12 minutes have passed with ACC ON. 1.
2.
3.
4.Except brake switch signal input
For the vehicles with A/T, when the START switch is pressed for 10 sec. or more, the ignition
status is changed to IGN ON and the engine start request signal is sent regardless of the brake
signal, provided that the initial ignition status is ACC ON and the gear selector lever is in P or N
position. *-