2011 SKODA FABIA Owner's Manual

Note
The seat heating should only be switched on when the engine is running. This has
a significant effect of saving on the battery capacity. 
Rear seats Folding the rear seats forwards Fig. 41 Fold the seat cushion forwards/unlock the seat backrest
To enlarge the luggage compartment, the rear seats can be folded forwards, if
necessary remove the seat cushions ⇒ page 56. The rear seats can be folded for-
ward individually on vehicles with divided rear seats.
Folding seats forwards
– Before folding the rear seats forwards, you must adapt the position of the
front seats in such a way that they are not damaged when the rear seats are
folded forwards.
– Pull up the seat cushion in direction of arrow 1 ⇒ fig. 41
and fold forwards in
direction of arrow 2 .
– Unlock the seat backrest by pressing the securing knob A and fold it forwards
⇒ fig. 41 on the right.
– Pull the head restraint out of the seat backrest.
– The head restraints can be inserted into the relevant holes of the folded for-
ward seat cushions ⇒ fig. 42.
– Fold the seat backrests fully fowards. Move seats into the initial position
–
Install the head restraint in the slightly lifted seat backrest.
– Then push the seat backrest back into the upright position until the securing
knob clicks into place - check by pulling on the seat backrest.
– Make sure that the red pin B is covered ⇒ fig. 41
on the right.
– Move the seat cushion into its original position. WARNING
● Ensure that the seat belts are not damaged when operating the seat
backrests. Under no circumstances must the rear seat belts be jammed by the
folded back seat backrests.
● The belts and the belt locks must be in their original position after folding
back the seat cushions and the seat backrests - they must be ready to use.
● Pay attention that the seat backrest is correctly interlocked. It is only then
that the three-point seat belt can reliably fulfil its function.
● The seat backrests must be securely interlocked in position so that no ob-
jects in the luggage compartment can slide into the passenger compartment if
there is sudden braking - risk of injury! Note
If the housing of the net partition is installed, first of all fold the left seat backrest
forward and then the right double seat backrest. 
Inserting head restraints in the seat cushions Fig. 42 Rear seats: Inserting head re-
straints in the seat cushions
£ 55
Seats and Stowage Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

–
The rear head restraints can be inserted into the relevant holes of the folded
forward seat cushions. 
Removing the seats Fig. 43 Removing the seats
The luggage compartment can be increased in size by removing the rear seat.
Removing
– Fold the seat cushion forwards completely.
– Press the wire clamps in the direction of the arrow ⇒ fig. 43 and remove the
seat cushion from its holder.
Install
– Press the wire clamps in the direction of the arrow and place it in its holder.
– Fold the seat cushion back into its original position. 
Pedals Concerning a secure depressing of the pedal, you should use only footmats from
the
ŠKODA Original Accessories.
Operation of the pedals must not be hindered! WARNING
● Greater pedal distances may be needed when there is a fault in the brake
system.
● Do not place any footmats or other additional floor coverings in the area of
the pedals in order to ensure that all the pedals can be fully depressed and are
able to return unobstructed to their initial position - risk of accident!
● There must be no objects on the floor which could roll under the pedals.
You would then no longer be able to apply the brakes, operate the clutch or
accelerator - risk of accident! 
luggage compartment
Loading the luggage compartment Please observe the following in the interest of maintaining good handling charac-
teristics of your vehicle:
–
Distribute the items of luggage as evenly as possible.
– Place heavy objects as far forward as possible.
– Attach the items of luggage to the lashing eyes or the fixing net
⇒ page 57.
In the event of an accident, there is such a high kinetic energy which is produced
by small and light objects that they can cause severe injuries. The magnitude of
the kinetic energy depends on the speed at which the vehicle is travelling and on
the weight of the object. The speed at which the vehicle is travelling is in this case
the more significant factor.
Example: In the event of a frontal collision at a speed of 50 km/h, an unsecured
object with a weight of 4.5 kg produces an energy, which corresponds to 20 times
its own weight. This means that it results in a weight of approx. 90 kg. You can
imagine the injuries that can occur, if this
“bullet” is flying through the interior
compartment and hits an occupant. £56
Seats and Stowage

WARNING
● Store the objects in the luggage compartment and attach them to the
lashing eyes.
● Loose objects in the passenger compartment can be thrown forward dur-
ing a sudden manoeuvre or in case of an accident and can injure the occupants
or other oncoming traffic. This risk is still increased, if the objects which are
flying around are hit by a deployed airbag. In this case, the objects which are
thrown back can injure the occupants - hazard.
● Please note that the handling properties of your vehicle may be affected
when transporting heavy objects as a result of the displacement of the centre
of gravity. The speed and style of driving must be adjusted accordingly.
● The items carried in the luggage compartment should be stored in such a
way that no objects are able to slip forward if there are any sudden driving or
braking manoeuvres undertaken - risk of injury!
● When transporting fastened objects which are sharp and dangerous in the
luggage compartment enlarged by folding the rear seats forward or removing
the rear seats, ensure the safety of the passengers transported on the other
rear seats ⇒  page 107, Correct seated position for the occupants on the rear
seats.
● If the rear seats next to the folded forward seat are occupied, ensure max-
imum safety, e.g. by placing the goods to be transported in such a way that a
folding back of the seat is prevented in case of a rear collision.
● Never drive with the boot lid fully opened or slightly ajar otherwise ex-
haust gases may get into the interior of the vehicle - risk of poisoning!
● On no account exceed the permissible axle loads and the permissible gross
weight of the vehicle - risk of accident!
● Never transport occupants in the luggage compartment. CAUTION
Please ensure that the heating elements of the rear window heater are not dam-
aged as a result of objects sliding in this area. Note
Tyre pressure must be adjusted to the load ⇒  fig. 135. Vehicles of category N1 On vehicles of the category N1, which are not fitted with a protective grille, a lash-
ing set which complies with the standard EN
12195 (1 - 4) must be used for fasten-
ing the load. 
Fastening elements Fig. 44 Luggage compartment: Lashing eyes and fastening elements (Fabia)/(Combi)
Fastening eyelets and fastening elements are located on the sides of the luggage
compartment for securing the items of luggage
⇒ fig. 44

.
You can also attach fixing nets to these fastening eyelets and fastening elements
for holding small objects. WARNING
● The load to be transported must be fixed in place in such a way that it can-
not move during the journey and when braking.
● If the items of luggage or objects are attached to the lashing eyes with un-
suitable or damaged lashing straps, injuries can occur in the event of braking
manoeuvres or accidents. In order to prevent the items of luggage being
thrown forward, always use suitable lashing straps which are firmly attached
to the lashing eyes. 57
Seats and Stowage Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

Fixing nets - Net programme
Fig. 45 Fixing net: double horizontal pocket, floor fixing net/double vertical pockets
Fixing examples of the fixing net as double horizontal pocket, floor fixing net
⇒ fig. 45 - left, and double vertical pockets ⇒ fig. 45 - right.
The fixing nets and the installation instruction are located in the luggage com-
partment. WARNING
● The strength of the net makes it possible to load the pocket with objects
of up to 1.5 kg in weight. Heavy objects are not secured sufficiently - risk of
injury and net damage!
● The load to be transported must be fixed in place in such a way that it can-
not move during the journey and when braking. CAUTION
Do not place any objects with sharp edges in the nets - risk of net damage. Folding hooks Fig. 46 Luggage compartment: folding
hook (Fabia)
Folding hooks for attaching small items of luggage, such as bags etc., are provided
on both sides of the luggage compartment ⇒ fig. 46. WARNING
Please refer to the following guidelines ⇒ page 56. CAUTION
An item of luggage weighing up to 7.5 kg can be attached to the hook. 
Luggage compartment cover You can use the luggage compartment cover behind the head re-
straints for storing light and soft items.
Fig. 47 Remove/install the luggage compartment cover
£58
Seats and Stowage

The luggage compartment cover can be removed as required if one must trans-
port bulky goods.
–
Unhook the support straps 1 ⇒ fig. 47.
– Remove the luggage compartment cover from the holders 2 by knocking
lightly on the bottom side of the cover in the area between the holders.
– To re-install, place the cover on the contact surfaces of the side trim panel and
position the mounts on the cover 3 above the holders
2 at the side trim
panel.
– Interlock the cover by lightly knocking on the top side of the cover in the area
between the holders.
– Attach the support straps 1 on the boot lid.
WARNING
No objects should be placed on the luggage compartment cover, the vehicle
occupants could be endangered if there is sudden braking or the vehicle col-
lides with something. CAUTION
When closing the boot lid, jamming and damage to the luggage compartment cov-
er or the side trim panel can occur if handled in an unprofessional way. Therefore,
check the following before closing:
● The mounts of the cover 3 must be interlocked on the holders of the side
trim panel 2 .
● The items which are transported must not exceed the level of the luggage
compartment cover.
● The cover must not be jammed in the seal of the boot lid when it is in the
opened position.
● There must be no object in the gap between the opened cover and the rear
seat backrest.
● Please ensure that the heating wire of the rear window heater is not damaged
as a result of objects placed in this area. Note
● When opening the boot lid, lift the luggage compartment cover - risk that ob-
jects placed in this area can slip forward! Further positions of the luggage compartment cover You can use the luggage compartment cover behind the head re-
straints for storing light and soft items.
Fig. 48 Luggage compartment cover in the lower position/stowed behind the rear seats
The luggage compartment cover can also be put into the lower position on the
supporting elements
⇒ fig. 48 - left.
The luggage compartment cover can also be stowed behind the rear seats
⇒ fig. 48 - right. CAUTION
In this position, the luggage compartment cover is designed for storing small ob-
jects of up to 2.5 kg. in weight. 
Foldable luggage compartment cover (Combi) Fig. 49 Luggage compartment: foldable luggage compartment cover/removing foldable lug-
gage compartment cover
£ 59
Seats and Stowage Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

Pulling out
–
Pull the foldable luggage compartment cover in direction of arrow 1 as far as
the stop into the secured position ⇒ fig. 49.
Folding
– Press the cover in the handle area in direction of arrow 2 , the cover rolls up
automatically.
Removing
– Have the foldable luggage compartment cover removed to transport bulky
goods by pressing on the side of the cross rod in direction of arrow 3 and tak-
ing it out by moving it in direction of arrow 4 ⇒ fig. 49
. WARNING
No objects should be placed on the luggage compartment cover, the vehicle
occupants could be endangered if there is sudden braking or the vehicle col-
lides with something. CAUTION
Please ensure that the heating elements of the rear window heater and the folda-
ble luggage compartment cover are not damaged as a result of objects transpor-
ted in this area. Variable loading floor in the luggage compartment
(Combi)
Remove variable loading floor Fig. 50 Luggage compartment: Fold up variable loading floor/remove
The variable loading floor makes it easier to handle bulky luggage and creates an
even luggage compartment floor when the rear seats are folded forward. The
maximum permissable surface load of the variable loading floor is 75 kg.
Removing the variable loading floor
– Unlock the variable loading floor by turning the locking bolts A by approx.
180° to the left ⇒ fig. 50.
– You can fold together the variable loading floor by moving it in the direction of
the arrow.
– Lift up the variable loading floor in direction of arrow 1 ⇒ fig. 50
and remove
it by pulling in direction of arrow 2 ⇒
 fig. 50 .
Installing the variable loading floor
– Place the variable loading floor once folded together onto the carrier rails.
– Fold open the variable loading floor.
– Lock the variabble loading floor by turning the locking bolts A by approx. 180°
to the right. WARNING
Pay attention when installing that the carrier rails and the variable loading
floor are correctly fixed, otherwise the occupants are at risk. £60
Seats and Stowage

Note
If the variable loading floor is installed in the luggage compartment, no flexible
storage compartment or fixing net can be installed ⇒ 
page 58.
Remove carrier rails Fig. 51 Luggage compartment: Slacken check points/remove carrier rails
Remove carrier rails
–
Slacken the check points B on the carrier rails using the vehicle key or a flat
screwdriver ⇒ fig. 51

.
– Grasp the carrier rail A at the position
1 ⇒
 fig. 51
and slacken it by pulling in
the direction of the arrow. You can take out the removable storage compart-
ments in order to facilitate the removal ⇒ page 71, Removeable storage com-
partments in the luggage compartment.
– Grasp the carrier rail A at the position
2 , slacken it by pulling in the direction
of the arrow and take it out.
– The carrier rail on the other side of the luggage compartment can be removed
in the same way.
Install carrier rails
– Position the carrier rails on the sides of the luggage compartment.
– Press both check points on each carrier rail up to the stop.
– Check the attachment of the carrier rails by pulling it. WARNING
Pay attention when installing that the carrier rails and the variable loading
floor are correctly fixed, otherwise the occupants are at risk. 
Dividing the luggage compartment with variable loading floor Fig. 52 Divide the luggage compartment
The luggage compartment can be divided with the variable loading floor.
– Lift up the part with the holder and secure it by sliding it into the grooves
⇒ fig. 52 . 
Luggage net partition (Combi) Use the luggage net partition behind the rear seats Fig. 53 Pull out the rear bulkhead/roll up
£ 61
Seats and Stowage Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

Pulling out
–
Open the right rear door.
– Fold down the rear seat backrests slightly forwards, which makes it possible to
clear the access for unrolling the rear bulkhead.
– Pull the rear bulkhead at the bracket A out of the housing
B in direction of
the holders C .
⇒  fig. 53
– Insert the cross rod into one of the mounts C .
– Insert the other end of the cross rod by pressing into the second mount.
– Press both ends of the cross rod forward into the function position.
– Then push the seat backrest back into the upright position until the locking
button clicks into place - check by pulling on the seat backrest ⇒  .
Folding
– Pull the cross rod back slightly, first on the one side then on the other side and
take the cross rod out of the mount C ⇒ fig. 53.
– Hold the cross rod in such a way that the luggage net partition can roll up
slowly and without damage into the housing B .
If you wish to use the entire luggage compartment, you can remove the foldable
luggage compartment cover ⇒ page 59. WARNING
● Ensure that the seat backrest on the rear seats is securely interlocked in
position when the vehicle is fitted with three-point safety belts for the middle
rear seat. It is only then that the three-point seat belt can reliably fulfil its
function.
● First check for yourself that the cross road is inserted into the mounts Cin the front position!
●
If the rear bulkhead is located behind the rear seats, then always make
sure that the rear seat backrest is correctly interlocked
. Use the luggage net partition behind the front seats
Fig. 54 Pull out the rear bulkhead/roll up
Pulling out
–
Open the right rear door.
– Fold the surfaces of the seats and seat backrests of the rear seats forward.
– Pull the luggage net partition at the bracket A out of the housing
B ⇒
 fig. 54 .
– First of all insert the cross rod into the mount C on one side.
– Insert into the mount on the other side the second end of the cross rod.
– Press both ends of the cross rod forward into the function position.
Folding
– Pull the cross rod back slightly, first on the one side then on the other side and
take the cross rod out of the mount C ⇒ fig. 54
.
– Hold the cross rod in such a way that the luggage net partition can roll up
slowly and without damage into the housing B .
– Fold the rear seats back into its original position. WARNING
First check for yourself that the cross road is inserted into the mounts C in
the front position! 62
Seats and Stowage