2011 RENAULT SCENIC Engine And Peripherals Siemens Injection Workshop Manual

13B-265
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
SC041
CHANGING COMMERCIAL VEHICLE IDLE SPEED
NOTESThis command is used to modify the commercial vehicle idle speed.
Kangoo II only.
To run this command, select scenario SC041 Modification of the commercial vehicle idle speed in the CLIP
diagnostic tool.
This command allows you to:
– read the commercial vehicle idle speed,
– activate the commercial vehicle idle speed at a predefined speed,
– deactivate or change the current commercial vehicle idle speed for the vehicle.
Predefined commercial vehicle idle speeds are:
– 1000 rpm,
– 1100 rpm.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
.
SID304_V4D_SC041 / SID304_V48_SC041 / SID301_V4C_SC041

13B-266
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
RZ005
PROGRAMMING
NOTESThis command enables you to reinitialise all the computer parameters.
Except for Kangoo II.
Command RZ005 reconfigures the computer.
When command RZ005 is run, all of the parameter information is cleared in the computer.
SID301_V44_RZ005 / SID304_V45_RZ005 / SID301_V48_RZ005 / SID304_V49_RZ005 / SID301_V4C_RZ005

13B-267
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
RZ019
REINITIALISE PROGRAMMING
NOTESThis command is used to reset the computer parameters according to the type of
operation or component repaired or replaced from the following list:
– the EGR valve,
– the damper valve,
– particle filter.
Ignition on and engine stopped.
To run this command, select command RZ019 Reinitialise programming on the CLIP diagnostic tool.
Procedure to be followed:
– on the main screen, select the component to reinitialise after an operation (removal/refitting or replacement of
component),
–select YES then OK to begin reinitialisation,
–select Finish on the Configuration completed screen to return to the main screen,
– end of operation.
SID301_V44_RZ019 / SID304_V45_RZ019 / SID301_V48_RZ019 / SID304_V49_RZ019 / SID304_V4D_RZ019 / SID301_V4C_RZ019

13B-268
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
RZ030
PARTICLE FILTER ADAPTIVES
NOTESRun the command only after replacing the particle filter.
Vdiag 45, 49 and 4D only.
Run command RZ030 Particle filter adaptives after replacing the particle filter.
SID304_V4D_RZ030 / SID301_V4C_RZ030

13B-269
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
AC236
COOLANT PUMP RELAY
NOTESThis command is used to check the operation of the electric coolant pump relay.
Use the CLIO III, MODUS, MEGANE II ph2 and SCENIC II ph2 Wiring Diagrams
Technical Note.
Vdiag 45, 49 and 4D only. (except Kangoo II).
Check the connection and condition of the coolant pump relay connector, component code 573 and injection
computer connector B, component code 120.
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3VG between components 573 and 120,
–3V between components 573 and 369,
–3FB between components 573 and 983,
–3FB1 between components 573 and 983.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
SID304_V45_AC236 / SID304_V49_AC236 / SID304_V4D_AC236 / SID301_V4C_AC236

13B-270
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
*temp.: temperatureAC239
PARTICLE FILTER TEMPERATURE SENSOR FAULT FINDING
NOTESCarry out this command only under the following conditions:
– DF999 Particle filter downstream temperature sensor circuit,
– DF1000 Particle filter upstream temperature sensor circuit,
With the ignition on and engine switched off and the engine coolant temperature
below 40°C.
This command is used to check the operation of the particle filter temperature sensors.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
diagrams Technical Note.
If one of the faults such as DF999 Particle filter downstream temperature sensor circuit or DF1000 Particle
filter upstream temperature sensor circuit is stored, check if it is in short circuit to the + 12 V or in open circuit
using this command.
Procedure:
– Run command AC239 Particle filter temperature sensor fault finding in the presence of the one of these
two faults DF999 Particle filter downstream temperature sensor circuit and/or DF1000 Particle filter
upstream temperature sensor circuit.
– If one or both of these faults becomes present, then the sensor(s) is in short circuit to + 12 V or in open
circuit.
Refer to the interpretation of faults DF999 Particle filter downstream temperature sensor circuit and DF1000
Particle filter upstream temperature sensor circuit.
– If they do not become present, clear the faults on the CLIP diagnostic tool.
SID304_V4D_AC239 / SID304_V45_AC239 / SID304_V49_AC239 / SID301_V4C_AC239

13B-271
MR-372-J84-13B050$858.mif
V17
13B
DIESEL INJECTION
Fault finding – Customer complaints
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
COMPUTER FAULT
NO DIALOGUE WITH THE COMPUTER ALP 1
STARTING FAULT
THE ENGINE DOES NOT START OR
STARTS WITH DIFFICULTYALP 2
STARTING DIFFICULT WITH COLD ENGINE ALP 3
IMPOSSIBLE TO SHUT OFF ENGINE
ALP 4
IDLING FAULTS
ENGINE IDLE SPEED TOO HIGH ALP 5
ENGINE IDLE SPEED TOO LOW OR
UNSTABLEALP 6
MR-372-J84-13B050$858.mif
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2

13B-272
MR-372-J84-13B050$858.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Customer complaints13B
DRIVING BEHAVIOUR
ENGINE CUT-OUT (STALLING) ALP 7
NO OR VERY LITTLE ACCELERATION,
INCREASE IN ENGINE SPEEDALP 8
ENGINE BUCKING ALP 9
ERRATIC ACCELERATION ALP 10
NO ENGINE BRAKING ALP 11
LOSS OF POWER ALP 12
TOO MUCH POWER ALP 13
OVERSPEED AT IDLE SPEED OR ON
RELEASING BRAKEALP 14
EXCESSIVE CONSUMPTION ALP 15
ENGINE OVERHEATING ALP 16
NOISE, ODOURS OR SMOKE
EMISSION CONTROL NOT SATISFACTORY ALP 17
ENGINE NOISE ALP 18
OIL LEAK FROM THE TURBOCHARGER ALP 19
SMOKE FROM THE EXHAUST ALP 20
REGENERATION
PARTICLE FILTER WARNING LIGHT ON ALP 21