2011 RENAULT SCENIC Engine And Peripherals EDC16 Injection Workshop Manual

13B-33
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF007
CONTINUED
CO.1
NOTESNone.
Check the rail pressure sensor connectors.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation against + 12 V of the following connections:
Injection computer brown 48-track connector B, track G3 Track 2 rail pressure sensor
Injection computer brown 48-track connector B, track C4 Track 1 rail pressure sensor
Repair if necessary.
if the fault is still present, replace the rail pressure sensor and tighten it to 35±5N.m.
Observe the safety advice in the Introduction.
1.DEF
2.DEF
NOTESNone.
Check the rail pressure sensor connectors.
Check the injection computer connections.
Repair if necessary.
Check the continuity and the absence of the interference resistance of the following connections:
Injection computer brown 48-track connector B, track G3 Track 2 rail pressure sensor
Injection computer brown 48-track connector B, track A4 Track 3 rail pressure sensor
Injection computer brown 48-track connector B, track C4 Track 1 rail pressure sensor
Repair if necessary.
With the ignition on and the engine stopped for more than one minute:
Display parameter PR038 Rail pressure in the Fuel circuit, Engine management function tab.
– If the value is below 50 bar, the sensor is in order.
In this case, contact the Techline.
– If the pressure is above 50 bar, replace the rail pressure sensor and tighten it to 35 ± 5 N.m.
Observe the safety advice in the Introduction.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-34
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF008
PRESENT
OR
STOREDPEDAL POTENTIOMETER CIRCUIT GANG 1
CO.0 : open circuit or short circuit to earth
CC.1 : short circuit to + 12 V
1.DEF : signal incoherence
2.DEF : accelerator pedal sensor locked
NOTESPriorities when dealing with a number of faults:
Deal with fault DF011 Sensor feed voltage no. 1 first if it is present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after a series of full-load/no-load actions on the
accelerator pedal.
Special notes:
Turbocharging and cruise control are not authorised.
The level 1 warning light comes on.
The engine speed is stuck at 1400 rpm if there is fault on gangs 1 and 2 of the pedal
potentiometer.
Use bornier Elé. 1681 for any work on the computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in Wiring check in the Introduction.
This check enables the condition and the conformity of the engine wiring harness to be checked.
CO.0
NOTESPriorities when dealing with a number of faults:
If fault DF009 Pedal potentiometer circuit gang 2 is
present at the same time, check that the pedal sensor
connector is connected correctly.
Check the pedal potentiometer connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation against earth of the following connections:
Injection computer, black 32-track connector A, track H2 Track 4 pedal potentiometer
connector
Injection computer, black 32-track connector A, track G2 Track 3 pedal potentiometer
connector
Repair if necessary.
Measure the resistance on the pedal potentiometer on track 1 between tracks 5 and 3.
Replace the pedal potentiometer if the resistance is not approximately 1.7 kΩ±0.9.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF008/EDC16_V48_DF008/EDC16_V4C_DF008

13B-35
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF008
CONTINUED 1
CC.1
NOTESNone.
Check the pedal potentiometer connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation against + 12 volts of the following connections:
Injection computer, black 32-track connector A, track H2 Track 4 pedal potentiometer
connector
Injection computer, black 32-track connector A, track H3 Track 5 pedal potentiometer
connector
Repair if necessary.
Measure the resistance on the pedal potentiometer on track 1 between tracks 5 and 3.
Replace the pedal potentiometer if the resistance is not approximately 1.7 kΩ±0.9.
1.DEF
NOTESNone.
Check the pedal potentiometer connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity, insulation and absence of interference resistance on the following connections:
Injection computer, black 32-track connector A, track H2 Track 4 pedal potentiometer
connector
Injection computer, black 32-track connector A, track G2 Track 3 pedal potentiometer
connector
Injection computer, black 32-track connector A, track H3 Track 5 pedal potentiometer
connector
Injection computer, black 32-track connector A, track F3 Track 1 pedal potentiometer
connector
Injection computer, black 32-track connector A, track F2 Track 2 pedal potentiometer
connector
Injection computer, black 32-track connector A, track F4 Track 6 pedal potentiometer
connector
Repair if necessary.
If the fault is still present, replace the pedal potentiometer.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-36
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 4C
DF008
CONTINUED 2
2.DEF
NOTESOnly in Vdiag 4C.
Check the mechanical condition of the accelerator pedal:
– locked in full load position,
– with the pedal blocked by an external component.
Check the brake light switch.
Repair if necessary.
Vary the position of the pedal and refer to the conformity check in order to check the operating values of the
accelerator pedal potentiometer.
If the values displayed are inconsistent, replace the accelerator pedal potentiometer.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.

13B-37
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF009
PRESENT
OR
STOREDPEDAL POTENTIOMETER CIRCUIT GANG 2
CO.0 : open circuit or short circuit to earth
CC.1 : short circuit to + 12 V
1.DEF : signal incoherence
NOTESPriorities when dealing with a number of faults:
Deal with fault DF011 Sensor feed voltage no. 1 first if it is present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after a series of full-load/no-load actions on the
accelerator pedal.
Special notes:
Turbocharging and cruise control are not authorised,
The level 1 warning light comes on.
The engine speed is stuck at 1400 rpm if there is fault on gangs 1 and 2 of the pedal
potentiometer.
Use bornier Elé. 1681 for any work on the computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This test enables the condition and the conformity of the engine wiring harness to be checked.
CO.0
NOTESPriorities when dealing with a number of faults:
if fault DF008 Pedal potentiometer circuit gang 1 is
present at the same time, check that the pedal is
connected correctly.
Check the pedal potentiometer connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity, insulation and absence of interference resistance on the following connections:
Injection computer, black 32-track connector A, track F3 Track 1 pedal potentiometer
connector
Injection computer, black 32-track connector A track F2 Track 2 pedal potentiometer
connector
Repair if necessary.
Measure the pedal sensor resistance on track 2 across tracks 2 and 6.
Replace the pedal potentiometer sensor if the resistance is not approximately 2.85 kΩ±2.05.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF009/EDC16_V48_DF009/EDC16_V4C_DF009

13B-38
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF009
CONTINUED
CC.1
NOTESPriorities when dealing with a number of faults:
Deal with fault DF012 Sensor feed voltage no. 2 first if it is
present or stored.
Check the pedal potentiometer connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation from + 12 V of the following connections:
Injection computer, black 32-track connector A, track F3 Track 1 pedal potentiometer connector
Injection computer, black 32-track connector A, track F4 Track 6 pedal potentiometer connector
Repair if necessary.
Measure the resistance of the pedal potentiometer on gang 2 between tracks 2 and 6.
Replace the pedal potentiometer sensor if the resistance measured is not approximately: 2.85 kΩ±2.05.
1.DEF
NOTESNone.
Check the pedal potentiometer connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity, insulation and absence of interference resistance on the following connections:
Injection computer black 32-track connector A, track F3 Track 1 pedal potentiometer connector
Injection computer black 32-track connector A, track F2 Track 2 pedal potentiometer connector
Injection computer black 32-track connector A, track F4 Track 6 pedal potentiometer connector
Injection computer black 32-track connector A, track H2 Track 4 pedal potentiometer connector
Injection computer black 32-track connector A, track G2 Track 3 pedal potentiometer connector
Injection computer black 32-track connector A, track H3 Track 5 pedal potentiometer connector
Repair if necessary.
If the fault is still present, replace the pedal potentiometer.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-39
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF011
PRESENT
OR
STOREDSENSOR SUPPLY VOLTAGE NO. 1
1.DEF : sensor reference voltage too weak
2.DEF : sensor reference voltage too high
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present following a road test or after attempting to start the
engine several times.
Special notes:
If the fault is present:
– cruise control is deactivated,
– the engine speed is limited,
–the level 1 warning light is lit.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This check enables the condition and the conformity of the engine wiring harness to be checked.
The sensors connected to supply no. 1 are:
–Turbocharging pressure sensor,
–Accelerator pedal potentiometer sensor, gang 1.
To locate a faulty sensor and/or connection, disconnect one of these sensors then check whether the fault
becomes stored.
If the fault is still present, start the operation again with the other sensor.
(wait a few seconds between each disconnection to allow the computer to perform the measurement).
If the fault is stored after a disconnection, replace the faulty sensor or repair its connection.
Clear the faults created by the multiple disconnections.
If the fault is still present when both these sensors have been disconnected:
1. Check the insulation from earth of the following connections:
Injection computer brown 48-track connector B, track K2 Track 3 of the turbocharger pressure
sensor
Injection computer brown 48-track connector B, track G4 Track 1 of the turbocharger pressure
sensor
Injection computer black 32-track connector A, track G2 Track 3 of the accelerator pedal
potentiometer gang 1
Injection computer black 32-track connector A, track H2 Track 4 of the accelerator pedal
potentiometer gang 1
Repair if necessary.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF011/EDC16_V48_DF011/EDC16_V4C_DF011

13B-40
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF011
CONTINUED
2. Check the insulation from + 12 V of the following connections:
Injection computer brown 48-track connector B, track K2 Track 3 of the turbocharger pressure
sensor
Injection computer brown 48-track connector B, track D4 Track 2 of the turbocharger pressure
sensor
Injection computer black 32-track connector A, track H3 Track 5 of the accelerator pedal
potentiometer gang 1
Injection computer black 32-track connector B, track H2 Track 4 of the accelerator pedal
potentiometer gang 1
Repair if necessary.
3. Check the insulation between the following connections after disconnecting the sensors:
–tracks3 and 5 of the pedal gang 1 sensor connector.
–tracks1 and 2 of the turbocharging pressure sensor connector.
If these checks do not produce the correct results, replace the faulty sensor(s).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.